u-boot/arch/arm/mach-omap2/am33xx/clk_synthesizer.c
Tom Rini b20e79f0bb Convert CONFIG_CLOCK_SYNTHESIZER to Kconfig
This converts the following to Kconfig:
   CONFIG_CLOCK_SYNTHESIZER

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 10:28:47 -04:00

137 lines
3.4 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* clk-synthesizer.c
*
* Clock synthesizer apis
*
* Copyright (C) 2016, Texas Instruments, Incorporated - http://www.ti.com/
*/
#include <common.h>
#include <asm/arch/clk_synthesizer.h>
#include <i2c.h>
/**
* clk_synthesizer_reg_read - Read register from synthesizer.
* dev: i2c bus device (not used if CONFIG_DM_I2C is not set)
* @addr: addr within the i2c device
* buf: Buffer to which value is to be read.
*
* For reading the register from this clock synthesizer, a command needs to
* be send along with enabling byte read more, and then read can happen.
* Returns 0 on success
*/
static int clk_synthesizer_reg_read(struct udevice *dev, int addr, u8 *buf)
{
int rc;
/* Enable Bye read */
addr = addr | CLK_SYNTHESIZER_BYTE_MODE;
#if !CONFIG_IS_ENABLED(DM_I2C)
/* Send the command byte */
rc = i2c_write(CONFIG_CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1);
if (rc)
printf("Failed to send command to clock synthesizer\n");
/* Read the Data */
return i2c_read(CONFIG_CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1);
#else
/* Send the command byte */
rc = dm_i2c_reg_write(dev, addr, *buf);
if (rc)
printf("Failed to send command to clock synthesizer\n");
/* Read the Data */
rc = dm_i2c_reg_read(dev, addr);
if (rc < 0)
return rc;
*buf = (u8)rc;
return 0;
#endif
}
/**
* clk_synthesizer_reg_write - Write a value to register in synthesizer.
* dev: i2c bus device (not used if CONFIG_DM_I2C is not set)
* @addr: addr within the i2c device
* val: Value to be written in the addr.
*
* Enable the byte read mode in the address and start the i2c transfer.
* Returns 0 on success
*/
static int clk_synthesizer_reg_write(struct udevice *dev, int addr, u8 val)
{
u8 cmd[2];
int rc = 0;
/* Enable byte write */
cmd[0] = addr | CLK_SYNTHESIZER_BYTE_MODE;
cmd[1] = val;
#if !CONFIG_IS_ENABLED(DM_I2C)
rc = i2c_write(CONFIG_CLK_SYNTHESIZER_I2C_ADDR, addr, 1, cmd, 2);
#else
rc = dm_i2c_write(dev, addr, cmd, 2);
#endif
if (rc)
printf("Clock synthesizer reg write failed at addr = 0x%x\n",
addr);
return rc;
}
/**
* setup_clock_syntherizer - Program the clock synthesizer to get the desired
* frequency.
* @data: Data containing the desired output
*
* This is a PLL-based high performance synthesizer which gives 3 outputs
* as per the PLL_DIV and load capacitor programmed.
*/
int setup_clock_synthesizer(struct clk_synth *data)
{
int rc;
u8 val = 0;
struct udevice *dev = NULL;
#if !CONFIG_IS_ENABLED(DM_I2C)
rc = i2c_probe(CONFIG_CLK_SYNTHESIZER_I2C_ADDR);
if (rc) {
printf("i2c probe failed at address 0x%x\n",
CONFIG_CLK_SYNTHESIZER_I2C_ADDR);
return rc;
}
#else
rc = i2c_get_chip_for_busnum(0, CONFIG_CLK_SYNTHESIZER_I2C_ADDR, 1, &dev);
if (rc) {
printf("failed to get device for synthesizer at address 0x%x\n",
CONFIG_CLK_SYNTHESIZER_I2C_ADDR);
return rc;
}
#endif
rc = clk_synthesizer_reg_read(dev, CLK_SYNTHESIZER_ID_REG, &val);
if (val != data->id)
return rc;
/* Crystal Load capacitor selection */
rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_XCSEL,
data->capacitor);
if (rc)
return rc;
rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_MUX_REG,
data->mux);
if (rc)
return rc;
rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_PDIV2_REG,
data->pdiv2);
if (rc)
return rc;
rc = clk_synthesizer_reg_write(dev, CLK_SYNTHESIZER_PDIV3_REG,
data->pdiv3);
if (rc)
return rc;
return 0;
}