mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-27 07:01:24 +00:00
537223afa6
As suggested by Eugene O'Brien <Eugene.O'Brien@advantechamt.com>, here an updated Bamboo README. Signed-off-by: Stefan Roese <sr@denx.de>
77 lines
3.3 KiB
Text
77 lines
3.3 KiB
Text
The 2 important dipswitches are configured as shown below:
|
|
|
|
SW1 (for 33MHz SysClk)
|
|
----------------------
|
|
S1 S2 S3 S4 S5 S6 S7 S8
|
|
OFF OFF OFF OFF OFF OFF OFF ON
|
|
|
|
SW7 (for Op-Code Flash and Boot Option H)
|
|
-----------------------------------------
|
|
S1 S2 S3 S4 S5 S6 S7 S8
|
|
OFF OFF OFF ON OFF OFF OFF OFF
|
|
|
|
The EEPROM at location 0x52 is loaded with these 16 bytes:
|
|
C47042A6 05D7A190 40082350 0d050000
|
|
|
|
SDR0_SDSTP0[ENG]: 1 : PLL's VCO is the source for PLL forward divisors
|
|
SDR0_SDSTP0[SRC]: 1 : Feedback originates from PLLOUTB
|
|
SDR0_SDSTP0[SEL]: 0 : Feedback selection is PLL output
|
|
SDR0_SDSTP0[TUNE]: 1000111000 : 10 <= M <= 22, 600MHz < VCO <= 900MHz
|
|
SDR0_SDSTP0[FBDV]: 4 : PLL feedback divisor
|
|
SDR0_SDSTP0[FBDVA]: 2 : PLL forward divisor A
|
|
SDR0_SDSTP0[FBDVB]: 5 : PLL forward divisor B
|
|
SDR0_SDSTP0[PRBDV0]: 1 : PLL primary divisor B
|
|
SDR0_SDSTP0[OPBDV0]: 2 : OPB clock divisor
|
|
SDR0_SDSTP0[LFBDV]: 1 : PLL local feedback divisor
|
|
SDR0_SDSTP0[PERDV0]: 3 : Peripheral clock divisor 0
|
|
SDR0_SDSTP0[MALDV0]: 2 : MAL clock divisor 0
|
|
SDR0_SDSTP0[PCIDV0]: 2 : Sync PCI clock divisor 0
|
|
SDR0_SDSTP0[PLLTIMER]: 7 : PLL locking timer
|
|
SDR0_SDSTP0[RW]: 1 : EBC ROM width: 16-bit
|
|
SDR0_SDSTP0[RL]: 0 : EBC ROM location: EBC
|
|
SDR0_SDSTP0[PAE]: 0 : PCI internal arbiter: disabled
|
|
SDR0_SDSTP0[PHCE]: 0 : PCI host configuration: disabled
|
|
SDR0_SDSTP0[ZM]: 3 : ZMII mode: RMII mode 100
|
|
SDR0_SDSTP0[CTE]: 0 : CPU trace: disabled
|
|
SDR0_SDSTP0[Nto1]: 0 : CPU/PLB ratio N/P: not N to 1
|
|
SDR0_SDSTP0[PAME]: 1 : PCI asynchronous mode: enabled
|
|
SDR0_SDSTP0[MEM]: 1 : Multiplex: EMAC
|
|
SDR0_SDSTP0[NE]: 0 : NDFC: disabled
|
|
SDR0_SDSTP0[NBW]: 0 : NDFC boot width: 8-bit
|
|
SDR0_SDSTP0[NBW]: 0 : NDFC boot page selection
|
|
SDR0_SDSTP0[NBAC]: 0 : NDFC boot address selection cycle: 3 Addr. Cycles, 1 Col. + 2 Row (512 page size)
|
|
SDR0_SDSTP0[NARE]: 0 : NDFC auto read : disabled
|
|
SDR0_SDSTP0[NRB]: 0 : NDFC Ready/Busy : Ready
|
|
SDR0_SDSTP0[NDRSC]: 33333 : NDFC device reset counter
|
|
SDR0_SDSTP0[NCG0]: 0 : NDFC/EBC chip select gating CS0 : EBC
|
|
SDR0_SDSTP0[NCG1]: 0 : NDFC/EBC chip select gating CS1 : EBC
|
|
SDR0_SDSTP0[NCG2]: 0 : NDFC/EBC chip select gating CS2 : EBC
|
|
SDR0_SDSTP0[NCG3]: 0 : NDFC/EBC chip select gating CS3 : EBC
|
|
SDR0_SDSTP0[NCRDC]: 3333 : NDFC device read count
|
|
|
|
PPC440EP Clocking Configuration
|
|
|
|
SysClk is 33.0MHz, M is 20, VCO is 660.0MHz, CPU is 330.0MHz, PLB is 132.0MHz
|
|
OPB is 66.0MHz, EBC is 44.0MHz, MAL is 66.0MHz, Sync PCI is 66.0MHz
|
|
|
|
The above information is reported by Eugene O'Brien
|
|
<Eugene.O'Brien@advantechamt.com>. Thanks a lot.
|
|
|
|
2007-08-06, Stefan Roese <sr@denx.de>
|
|
---------------------------------------------------------------------
|
|
|
|
The configuration for the AMCC 440EP eval board "Bamboo" was changed
|
|
to only use 384 kbytes of FLASH for the U-Boot image. This way the
|
|
redundant environment can be saved in the remaining 2 sectors of the
|
|
same flash chip.
|
|
|
|
Caution: With an upgrade from an earlier U-Boot version the current
|
|
environment will be erased since the environment is now saved in
|
|
different sectors. By using the following command the environment can
|
|
be saved after upgrading the U-Boot image and *before* resetting the
|
|
board:
|
|
|
|
setenv recover_env 'prot off FFF80000 FFF9FFFF;era FFF80000 FFF9FFFF;' \
|
|
'cp.b FFF60000 FFF80000 20000'
|
|
|
|
2006-07-27, Stefan Roese <sr@denx.de>
|