u-boot/include/configs/kmeter1.h
Mike Frysinger bdab39d358 rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment.  So, let's make sure the define is named accordingly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18 00:47:43 +01:00

457 lines
15 KiB
C

/*
* Copyright (C) 2006 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
*
* Copyright (C) 2007 Logic Product Development, Inc.
* Peter Barada <peterb@logicpd.com>
*
* Copyright (C) 2007 MontaVista Software, Inc.
* Anton Vorontsov <avorontsov@ru.mvista.com>
*
* (C) Copyright 2008
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_QE 1 /* Has QE */
#define CONFIG_MPC83XX 1 /* MPC83XX family */
#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
#define CONFIG_KMETER1 1 /* KMETER1 board specific */
/* include common defines/options for all Keymile boards */
#include "keymile-common.h"
/*
* System Clock Setup
*/
#define CONFIG_83XX_CLKIN 66000000
#define CONFIG_SYS_CLK_FREQ 66000000
#define CONFIG_83XX_PCICLK 66000000
/*
* Hardware Reset Configuration Word
*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_CSB_TO_CLKIN_4X1 | \
HRCWL_CORE_TO_CSB_2X1 | \
HRCWL_CE_PLL_VCO_DIV_2 | \
HRCWL_CE_TO_PLL_1X6 )
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_CORE_ENABLE | \
HRCWH_FROM_0X00000100 | \
HRCWH_BOOTSEQ_NORMAL | \
HRCWH_SW_WATCHDOG_DISABLE | \
HRCWH_ROM_LOC_LOCAL_16BIT | \
HRCWH_BIG_ENDIAN | \
HRCWH_LDP_CLEAR )
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH 0x00000006
#define CONFIG_SYS_SICRL 0x00000000
/*
* IMMR new address
*/
#define CONFIG_SYS_IMMR 0xE0000000
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CFG_83XX_DDR_USES_CS0
#undef CONFIG_DDR_ECC
/*
* DDRCDR - DDR Control Driver Register
*/
#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */
/*
* Manually set up DDR parameters
*/
#define CONFIG_DDR_II
#define CONFIG_SYS_DDR_SIZE 256 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
CSCONFIG_ROW_BIT_13 | \
CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS)
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
SDRAM_CFG_SREN)
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CONFIG_SYS_DDR_INTERVAL ((0x100 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
(0x406 << SDRAM_INTERVAL_REFINT_SHIFT))
#define CONFIG_SYS_DDR_MODE 0x04440242
#define CONFIG_SYS_DDR_MODE2 0x00800000
#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
(0 << TIMING_CFG0_WWT_SHIFT) | \
(0 << TIMING_CFG0_RRT_SHIFT) | \
(0 << TIMING_CFG0_WRT_SHIFT) | \
(0 << TIMING_CFG0_RWT_SHIFT))
#define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_40) | \
( 2 << TIMING_CFG1_WRTORD_SHIFT) | \
( 1 << TIMING_CFG1_ACTTOACT_SHIFT) | \
( 2 << TIMING_CFG1_WRREC_SHIFT) | \
( 2 << TIMING_CFG1_REFREC_SHIFT) | \
( 2 << TIMING_CFG1_ACTTORW_SHIFT) | \
( 6 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
( 2 << TIMING_CFG1_PRETOACT_SHIFT))
#define CONFIG_SYS_DDR_TIMING_2 ((5 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
(1 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
(3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
(0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
(4 << TIMING_CFG2_CPO_SHIFT))
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CONFIG_SYS_FLASH_BASE 0xF0000000
#define CONFIG_SYS_FLASH_BASE_1 0xF2000000
#define CONFIG_SYS_PIGGY_BASE 0x80000000
#define CONFIG_SYS_PAXE_BASE 0xA0000000
#define CONFIG_SYS_PAXE_SIZE 256
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4)
/*
* Init Local Bus Memory Controller:
*
* Bank Bus Machine PortSz Size Device
* ---- --- ------- ------ ----- ------
* 0 Local GPCM 16 bit 256MB FLASH
* 1 Local GPCM 8 bit 256KB GPIO/PIGGY
* 3 Local GPCM 8 bit 256MB PAXE
*
*/
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
#define CONFIG_SYS_FLASH_PROTECTION 1
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V)
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
OR_GPCM_SCY_5 | \
OR_GPCM_TRLX | OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 }
#undef CONFIG_SYS_FLASH_CHECKSUM
/*
* PRIO1/PIGGY on the local bus CS1
*/
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */
#define CONFIG_SYS_LBLAWAR1_PRELIM 0x80000011 /* 256KB window size */
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \
(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
BR_V)
#define CONFIG_SYS_OR1_PRELIM (0xfffc0000 | /* 256KB */ \
OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
OR_GPCM_SCY_2 | \
OR_GPCM_TRLX | OR_GPCM_EAD)
/*
* PAXE on the local bus CS3
*/
#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */
#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001b /* 256MB window size */
#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE | \
(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
BR_V)
#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \
OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
OR_GPCM_SCY_2 | \
OR_GPCM_TRLX | OR_GPCM_EAD)
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS
/*
* General PCI
* Addresses are mapped 1-1.
*/
#undef CONFIG_PCI /* No PCI */
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif
/*
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_UEC_ETH1 /* GETH1 */
#define UEC_VERBOSE_DEBUG 1
#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 0
#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII
#endif
/*
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#else /* CFG_RAMBOOT */
#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif /* CFG_RAMBOOT */
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_256K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* PAXE: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_DBAT6L CFG_IBAT6L
#define CFG_DBAT6U CFG_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_DBAT7L CFG_IBAT7L
#define CFG_DBAT7U CFG_IBAT7U
#else /* CONFIG_PCI */
#define CONFIG_SYS_IBAT6L (0)
#define CONFIG_SYS_IBAT6U (0)
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_SYS_IBAT7U (0)
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#endif /* CONFIG_PCI */
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs}" \
" console=ttyS0,${baudrate}\0" \
"fdt_addr=f0080000\0" \
"kernel_addr=f00a0000\0" \
"ramdisk_addr=f03a0000\0" \
"kernel_addr_r=400000\0" \
"fdt_addr_r=800000\0" \
"ramdisk_addr_r=810000\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr} - ${fdt_addr}\0" \
"net_nfs=tftp ${kernel_addr_r} ${boot_file}; " \
"tftp ${fdt_addr_r} ${fdt_file}; " \
"run nfsargs addip addtty;" \
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
"fdt_file=/tftpboot/kmeter1/kmeter1.dtb\0" \
"boot_file=/tftpboot/kmeter1/uImage\0" \
"ramdisk_file=/tftpboot/kmeter1/uRamdisk\0" \
"u-boot=/tftpboot/kmeter1/u-boot.bin\0" \
"loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0" \
"load=tftp $loadaddr ${u-boot}\0" \
"update=protect off " MK_STR(TEXT_BASE) " +$filesize;" \
"erase " MK_STR(TEXT_BASE) " +$filesize;" \
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \
"protect on " MK_STR(TEXT_BASE) " +$filesize;" \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \
"setenv filesize;saveenv\0" \
"upd=run load update\0" \
"loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0" \
"loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \
"loadkernel=tftp ${kernel_addr_r} ${boot_file}\0" \
"unlock=yes\0" \
""
#endif /* __CONFIG_H */