u-boot/board/kosagi/novena/novena_spl.c
Eric Nelson 7f17fb7400 mx6: ddr: pass mx6_ddr_sysinfo to calibration routines
The DDR calibration routines have scattered support for bus
widths other than 64-bits:

-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.

Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.

This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-11-29 16:40:12 +01:00

616 lines
17 KiB
C

/*
* Novena SPL
*
* Copyright (C) 2014 Marek Vasut <marex@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/arch/crm_regs.h>
#include <i2c.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <spl.h>
#include <asm/arch/mx6-ddr.h>
#include "novena.h"
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define ENET_PHY_CFG_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_22K_UP | PAD_CTL_HYS)
#define RGMII_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define SPI_PAD_CTRL \
(PAD_CTL_HYS | \
PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
#define I2C_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_240ohm | PAD_CTL_HYS | \
PAD_CTL_ODE)
#define BUTTON_PAD_CTRL \
(PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/*
* Audio
*/
static iomux_v3_cfg_t audio_pads[] = {
/* AUD_PWRON */
MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void novena_spl_setup_iomux_audio(void)
{
imx_iomux_v3_setup_multiple_pads(audio_pads, ARRAY_SIZE(audio_pads));
gpio_direction_output(NOVENA_AUDIO_PWRON, 1);
}
/*
* ENET
*/
static iomux_v3_cfg_t enet_pads1[] = {
MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
/* pin 35, PHY_AD2 */
MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
/* pin 32, MODE0 */
MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
/* pin 31, MODE1 */
MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
/* pin 28, MODE2 */
MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
/* pin 27, MODE3 */
MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
/* pin 33, CLK125_EN */
MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
/* pin 42 PHY nRST */
MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t enet_pads2[] = {
MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(RGMII_PAD_CTRL),
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(RGMII_PAD_CTRL),
};
static void novena_spl_setup_iomux_enet(void)
{
imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
/* Assert Ethernet PHY nRST */
gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
/*
* Use imx6 internal pull-ups to drive PHY mode pins during PHY reset
* de-assertion. The intention is to use weak signal drivers (pull-ups)
* to prevent the conflict between PHY pins becoming outputs after
* reset and imx6 still driving the pins. The issue is described in PHY
* datasheet, p.14
*/
gpio_direction_input(IMX_GPIO_NR(6, 30)); /* PHY_AD2 = 1 */
gpio_direction_input(IMX_GPIO_NR(6, 25)); /* MODE0 = 1 */
gpio_direction_input(IMX_GPIO_NR(6, 27)); /* MODE1 = 1 */
gpio_direction_input(IMX_GPIO_NR(6, 28)); /* MODE2 = 1 */
gpio_direction_input(IMX_GPIO_NR(6, 29)); /* MODE3 = 1 */
gpio_direction_input(IMX_GPIO_NR(6, 24)); /* CLK125_EN = 1 */
/* Following reset timing (p.53, fig.8 from the PHY datasheet) */
mdelay(10);
/* De-assert Ethernet PHY nRST */
gpio_set_value(IMX_GPIO_NR(3, 23), 1);
/* PHY is now configured, connect FEC to the pads */
imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
/*
* PHY datasheet recommends on p.53 to wait at least 100us after reset
* before using MII, so we enforce the delay here
*/
udelay(100);
}
/*
* FPGA
*/
static iomux_v3_cfg_t fpga_pads[] = {
/* FPGA_RESET_N */
MX6_PAD_DISP0_DAT13__GPIO5_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void novena_spl_setup_iomux_fpga(void)
{
imx_iomux_v3_setup_multiple_pads(fpga_pads, ARRAY_SIZE(fpga_pads));
gpio_direction_output(NOVENA_FPGA_RESET_N_GPIO, 0);
}
/*
* GPIO Button
*/
static iomux_v3_cfg_t button_pads[] = {
/* Debug */
MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
};
static void novena_spl_setup_iomux_buttons(void)
{
imx_iomux_v3_setup_multiple_pads(button_pads, ARRAY_SIZE(button_pads));
}
/*
* I2C
*/
/*
* I2C1:
* 0x1d ... MMA7455L
* 0x30 ... SO-DIMM temp sensor
* 0x44 ... STMPE610
* 0x50 ... SO-DIMM ID
*/
struct i2c_pads_info i2c_pad_info0 = {
.scl = {
.i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC,
.gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC,
.gp = IMX_GPIO_NR(3, 21)
},
.sda = {
.i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC,
.gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC,
.gp = IMX_GPIO_NR(3, 28)
}
};
/*
* I2C2:
* 0x08 ... PMIC
* 0x3a ... HDMI DCC
* 0x50 ... HDMI DCC
*/
static struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
.gp = IMX_GPIO_NR(2, 30)
},
.sda = {
.i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
.gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
.gp = IMX_GPIO_NR(3, 16)
}
};
/*
* I2C3:
* 0x11 ... ES8283
* 0x50 ... LCD EDID
* 0x56 ... EEPROM
*/
static struct i2c_pads_info i2c_pad_info2 = {
.scl = {
.i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
.gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
.gp = IMX_GPIO_NR(3, 17)
},
.sda = {
.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
.gp = IMX_GPIO_NR(3, 18)
}
};
static void novena_spl_setup_iomux_i2c(void)
{
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
}
/*
* PCI express
*/
#ifdef CONFIG_CMD_PCI
static iomux_v3_cfg_t pcie_pads[] = {
/* "Reset" pin */
MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* "Power on" pin */
MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* "Wake up" pin (input) */
MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* "Disable endpoint" (rfkill) pin */
MX6_PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void novena_spl_setup_iomux_pcie(void)
{
imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
/* Ensure PCIe is powered down */
gpio_direction_output(NOVENA_PCIE_POWER_ON_GPIO, 0);
/* Put the card into reset */
gpio_direction_output(NOVENA_PCIE_RESET_GPIO, 0);
/* Input signal to wake system from mPCIe card */
gpio_direction_input(NOVENA_PCIE_WAKE_UP_GPIO);
/* Drive RFKILL high, to ensure the radio is turned on */
gpio_direction_output(NOVENA_PCIE_DISABLE_GPIO, 1);
}
#else
static inline void novena_spl_setup_iomux_pcie(void) {}
#endif
/*
* SDHC
*/
static iomux_v3_cfg_t usdhc2_pads[] = {
MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* WP */
MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
};
static iomux_v3_cfg_t usdhc3_pads[] = {
MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
static void novena_spl_setup_iomux_sdhc(void)
{
imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
/* Big SD write-protect and card-detect */
gpio_direction_input(IMX_GPIO_NR(1, 2));
gpio_direction_input(IMX_GPIO_NR(1, 4));
}
/*
* SPI
*/
#ifdef CONFIG_MXC_SPI
static iomux_v3_cfg_t ecspi3_pads[] = {
/* SS1 */
MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT3__GPIO4_IO24 | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT4__GPIO4_IO25 | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT5__GPIO4_IO26 | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT7__ECSPI3_RDY | MUX_PAD_CTRL(SPI_PAD_CTRL),
};
static void novena_spl_setup_iomux_spi(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi3_pads, ARRAY_SIZE(ecspi3_pads));
/* De-assert the nCS */
gpio_direction_output(MX6_PAD_DISP0_DAT3__GPIO4_IO24, 1);
gpio_direction_output(MX6_PAD_DISP0_DAT4__GPIO4_IO25, 1);
gpio_direction_output(MX6_PAD_DISP0_DAT5__GPIO4_IO26, 1);
}
#else
static void novena_spl_setup_iomux_spi(void) {}
#endif
/*
* UART
*/
static iomux_v3_cfg_t const uart2_pads[] = {
MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const uart3_pads[] = {
MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const uart4_pads[] = {
MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT16__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT17__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static void novena_spl_setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}
/*
* Video
*/
#ifdef CONFIG_VIDEO
static iomux_v3_cfg_t hdmi_pads[] = {
/* "Ghost HPD" pin */
MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* LCD_PWR_CTL */
MX6_PAD_CSI0_DAT10__GPIO5_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* LCD_BL_ON */
MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* GPIO_PWM1 */
MX6_PAD_DISP0_DAT8__GPIO4_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void novena_spl_setup_iomux_video(void)
{
imx_iomux_v3_setup_multiple_pads(hdmi_pads, ARRAY_SIZE(hdmi_pads));
gpio_direction_input(NOVENA_HDMI_GHOST_HPD);
}
#else
static inline void novena_spl_setup_iomux_video(void) {}
#endif
/*
* SPL boots from uSDHC card
*/
#ifdef CONFIG_FSL_ESDHC
static struct fsl_esdhc_cfg usdhc_cfg = {
USDHC3_BASE_ADDR, 0, 4
};
int board_mmc_getcd(struct mmc *mmc)
{
/* There is no CD for a microSD card, assume always present. */
return 1;
}
int board_mmc_init(bd_t *bis)
{
usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
return fsl_esdhc_initialize(bis, &usdhc_cfg);
}
#endif
/* Configure MX6Q/DUAL mmdc DDR io registers */
static struct mx6dq_iomux_ddr_regs novena_ddr_ioregs = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
.dram_sdclk_0 = 0x00020038,
.dram_sdclk_1 = 0x00020038,
.dram_cas = 0x00000038,
.dram_ras = 0x00000038,
.dram_reset = 0x00000038,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00000038,
.dram_sdcke1 = 0x00000038,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 40 ohm */
.dram_sdodt0 = 0x00000038,
.dram_sdodt1 = 0x00000038,
/* SDQS[0:7]: Differential input, 40 ohm */
.dram_sdqs0 = 0x00000038,
.dram_sdqs1 = 0x00000038,
.dram_sdqs2 = 0x00000038,
.dram_sdqs3 = 0x00000038,
.dram_sdqs4 = 0x00000038,
.dram_sdqs5 = 0x00000038,
.dram_sdqs6 = 0x00000038,
.dram_sdqs7 = 0x00000038,
/* DQM[0:7]: Differential input, 40 ohm */
.dram_dqm0 = 0x00000038,
.dram_dqm1 = 0x00000038,
.dram_dqm2 = 0x00000038,
.dram_dqm3 = 0x00000038,
.dram_dqm4 = 0x00000038,
.dram_dqm5 = 0x00000038,
.dram_dqm6 = 0x00000038,
.dram_dqm7 = 0x00000038,
};
/* Configure MX6Q/DUAL mmdc GRP io registers */
static struct mx6dq_iomux_grp_regs novena_grp_ioregs = {
/* DDR3 */
.grp_ddr_type = 0x000c0000,
.grp_ddrmode_ctl = 0x00020000,
/* Disable DDR pullups */
.grp_ddrpke = 0x00000000,
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
.grp_addds = 0x00000038,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
.grp_ctlds = 0x00000038,
/* DATA[00:63]: Differential input, 40 ohm */
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000038,
.grp_b1ds = 0x00000038,
.grp_b2ds = 0x00000038,
.grp_b3ds = 0x00000038,
.grp_b4ds = 0x00000038,
.grp_b5ds = 0x00000038,
.grp_b6ds = 0x00000038,
.grp_b7ds = 0x00000038,
};
static struct mx6_mmdc_calibration novena_mmdc_calib = {
/* write leveling calibration determine */
.p0_mpwldectrl0 = 0x00420048,
.p0_mpwldectrl1 = 0x006f0059,
.p1_mpwldectrl0 = 0x005a0104,
.p1_mpwldectrl1 = 0x01070113,
/* Read DQS Gating calibration */
.p0_mpdgctrl0 = 0x437c040b,
.p0_mpdgctrl1 = 0x0413040e,
.p1_mpdgctrl0 = 0x444f0446,
.p1_mpdgctrl1 = 0x044d0422,
/* Read Calibration: DQS delay relative to DQ read access */
.p0_mprddlctl = 0x4c424249,
.p1_mprddlctl = 0x4e48414f,
/* Write Calibration: DQ/DM delay relative to DQS write access */
.p0_mpwrdlctl = 0x42414641,
.p1_mpwrdlctl = 0x46374b43,
};
static struct mx6_ddr_sysinfo novena_ddr_info = {
/* Width of data bus: 0=16, 1=32, 2=64 */
.dsize = 2,
/* Config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
/* Single chip select */
.ncs = 1,
.cs1_mirror = 0,
.rtt_wr = 0, /* RTT_Wr = RZQ/4 */
.rtt_nom = 1, /* RTT_Nom = RZQ/2 */
.walat = 0, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.refsel = 1, /* Refresh cycles at 32KHz */
.refr = 7, /* 8 refresh commands per refresh cycle */
};
static struct mx6_ddr3_cfg elpida_4gib_1600 = {
.mem_speed = 1600,
.density = 4,
.width = 64,
.banks = 8,
.rowaddr = 16,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0xFFFFF300, &ccm->CCGR4);
writel(0x0F0000C3, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void gpr_init(void)
{
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
/* enable AXI cache for VDOA/VPU/IPU */
writel(0xF00000CF, &iomux->gpr[4]);
/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
writel(0x007F007F, &iomux->gpr[6]);
writel(0x007F007F, &iomux->gpr[7]);
}
/*
* called from C runtime startup code (arch/arm/lib/crt0.S:_main)
* - we have a stack and a place to store GD, both in SRAM
* - no variable global data is available
*/
void board_init_f(ulong dummy)
{
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
gpr_init();
/* setup GP timer */
timer_init();
#ifdef CONFIG_BOARD_POSTCLK_INIT
board_postclk_init();
#endif
#ifdef CONFIG_FSL_ESDHC
get_clocks();
#endif
/* Setup IOMUX and configure basics. */
novena_spl_setup_iomux_audio();
novena_spl_setup_iomux_buttons();
novena_spl_setup_iomux_enet();
novena_spl_setup_iomux_fpga();
novena_spl_setup_iomux_i2c();
novena_spl_setup_iomux_pcie();
novena_spl_setup_iomux_sdhc();
novena_spl_setup_iomux_spi();
novena_spl_setup_iomux_uart();
novena_spl_setup_iomux_video();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* Start the DDR DRAM */
mx6dq_dram_iocfg(64, &novena_ddr_ioregs, &novena_grp_ioregs);
mx6_dram_cfg(&novena_ddr_info, &novena_mmdc_calib, &elpida_4gib_1600);
/* Perform DDR DRAM calibration */
udelay(100);
mmdc_do_write_level_calibration(&novena_ddr_info);
mmdc_do_dqs_calibration(&novena_ddr_info);
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}