u-boot/board/logicpd/zoom2/zoom2_serial.c
Marek Vasut 425101e115 serial: zoom2: Remove zoom2 serial prototypes from serial.h
Remove the prototypes for zoom2_serial_deviceN from serial.h . This
can't be done right away, as they are referenced from the zoom2
config file. Therefore, adjust the code so the config file only
specifies number of the port. Then, replace the simple return in
default_serial_console() with a switch across possible values, which
returns the zoom2_serial_deviceN . With such adjustment in place,
the exported prototypes in serial.h can be safely removed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
2012-10-15 11:53:50 -07:00

144 lines
3.5 KiB
C

/*
* Copyright (c) 2009 Wind River Systems, Inc.
* Tom Rix <Tom.Rix@windriver.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
* This file was adapted from arch/powerpc/cpu/mpc5xxx/serial.c
*
*/
#include <common.h>
#include <serial.h>
#include <ns16550.h>
#include <asm/arch/cpu.h>
#include "zoom2_serial.h"
int quad_init_dev (unsigned long base)
{
/*
* The Quad UART is on the debug board.
* Check if the debug board is attached before using the UART
*/
if (zoom2_debug_board_connected ()) {
NS16550_t com_port = (NS16550_t) base;
int baud_divisor = CONFIG_SYS_NS16550_CLK / 16 /
CONFIG_BAUDRATE;
/*
* Zoom2 has a board specific initialization of its UART.
* This generic initialization has been copied from
* drivers/serial/ns16550.c. The macros have been expanded.
*
* Do the following instead of
*
* NS16550_init (com_port, clock_divisor);
*/
com_port->ier = 0x00;
/*
* On Zoom2 board Set pre-scalar to 1
* CLKSEL is GND => MCR[7] is 1 => preslr is 4
* So change the prescl to 1
*/
com_port->lcr = 0xBF;
com_port->fcr |= 0x10;
com_port->mcr &= 0x7F;
/* This is generic ns16550.c setup */
com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
com_port->dll = 0;
com_port->dlm = 0;
com_port->lcr = UART_LCR_8N1;
com_port->mcr = UART_MCR_DTR | UART_MCR_RTS;
com_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR |
UART_FCR_TXSR;
com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
com_port->dll = baud_divisor & 0xff;
com_port->dlm = (baud_divisor >> 8) & 0xff;
com_port->lcr = UART_LCR_8N1;
}
/*
* We have to lie here, otherwise the board init code will hang
* on the check
*/
return 0;
}
void quad_putc_dev (unsigned long base, const char c)
{
if (zoom2_debug_board_connected ()) {
if (c == '\n')
quad_putc_dev (base, '\r');
NS16550_putc ((NS16550_t) base, c);
} else {
usbtty_putc(c);
}
}
void quad_puts_dev (unsigned long base, const char *s)
{
if (zoom2_debug_board_connected ()) {
while ((s != NULL) && (*s != '\0'))
quad_putc_dev (base, *s++);
} else {
usbtty_puts(s);
}
}
int quad_getc_dev (unsigned long base)
{
if (zoom2_debug_board_connected ())
return NS16550_getc ((NS16550_t) base);
return usbtty_getc();
}
int quad_tstc_dev (unsigned long base)
{
if (zoom2_debug_board_connected ())
return NS16550_tstc ((NS16550_t) base);
return usbtty_tstc();
}
void quad_setbrg_dev (unsigned long base)
{
if (zoom2_debug_board_connected ()) {
int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 /
CONFIG_BAUDRATE;
NS16550_reinit ((NS16550_t) base, clock_divisor);
}
}
QUAD_INIT (0)
QUAD_INIT (1)
QUAD_INIT (2)
QUAD_INIT (3)
struct serial_device *default_serial_console(void)
{
switch (ZOOM2_DEFAULT_SERIAL_DEVICE) {
case 0: return &zoom2_serial_device0;
case 1: return &zoom2_serial_device1;
case 2: return &zoom2_serial_device2;
case 3: return &zoom2_serial_device3;
}
}