u-boot/board/freescale/t4rdb/t4240rdb.c
Ying Zhang 2f66a828f7 powerpc/board/t4240rdb: Enable VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:38:05 -08:00

147 lines
3.1 KiB
C

/*
* Copyright 2014 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <command.h>
#include <i2c.h>
#include <netdev.h>
#include <linux/compiler.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
#include "t4rdb.h"
#include "cpld.h"
#include "../common/vid.h"
DECLARE_GLOBAL_DATA_PTR;
int checkboard(void)
{
struct cpu_type *cpu = gd->arch.cpu;
u8 sw;
printf("Board: %sRDB, ", cpu->name);
printf("Board rev: 0x%02x CPLD ver: 0x%02x%02x, ",
CPLD_READ(hw_ver), CPLD_READ(sw_maj_ver), CPLD_READ(sw_min_ver));
sw = CPLD_READ(vbank);
sw = sw & CPLD_BANK_SEL_MASK;
if (sw <= 7)
printf("vBank: %d\n", sw);
else
printf("Unsupported Bank=%x\n", sw);
puts("SERDES Reference Clocks:\n");
printf(" SERDES1=100MHz SERDES2=156.25MHz\n"
" SERDES3=100MHz SERDES4=100MHz\n");
return 0;
}
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
int flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash + PROMJET region to caching-inhibited
* so that flash can be erased properly.
*/
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
if (flash_esel == -1) {
/* very unlikely unless something is messed up */
puts("Error: Could not find TLB for FLASH BASE\n");
flash_esel = 2; /* give our best effort to continue */
} else {
/* invalidate existing TLB entry for flash + promjet */
disable_tlb(flash_esel);
}
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, flash_esel, BOOKE_PAGESZ_256M, 1);
/*
* Adjust core voltage according to voltage ID
* This function changes I2C mux to channel 2.
*/
if (adjust_vdd(0))
printf("Warning: Adjusting core voltage failed.\n");
return 0;
}
int misc_init_r(void)
{
return 0;
}
int ft_board_setup(void *blob, bd_t *bd)
{
phys_addr_t base;
phys_size_t size;
ft_cpu_setup(blob, bd);
base = getenv_bootm_low();
size = getenv_bootm_size();
fdt_fixup_memory(blob, (u64)base, (u64)size);
#ifdef CONFIG_PCI
pci_of_setup(blob, bd);
#endif
fdt_fixup_liodn(blob);
fdt_fixup_dr_usb(blob, bd);
#ifdef CONFIG_SYS_DPAA_FMAN
fdt_fixup_fman_ethernet(blob);
fdt_fixup_board_enet(blob);
#endif
return 0;
}
/*
* This function is called by bdinfo to print detail board information.
* As an exmaple for future board, we organize the messages into
* several sections. If applicable, the message is in the format of
* <name> = <value>
* It should aligned with normal output of bdinfo command.
*
* Voltage: Core, DDR and another configurable voltages
* Clock : Critical clocks which are not printed already
* RCW : RCW source if not printed already
* Misc : Other important information not in above catagories
*/
void board_detail(void)
{
int rcwsrc;
/* RCW section SW3[4] */
rcwsrc = 0x0;
puts("RCW source = ");
switch (rcwsrc & 0x1) {
case 0x1:
puts("SDHC/eMMC\n");
break;
default:
puts("I2C normal addressing\n");
break;
}
}