mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-04 18:41:03 +00:00
64f5e3b492
System controllers are pretty much the same on the all boards that's why use autodetection based on i2c eeprom. This should end up with having only one BSP for all SCs with only DT overlays to cover different i2c structures. All MIOs are fixed by the spec that's why not a problem to description pinctrl setting. Apart from eth phy reset, it also set proper phy delays. The TI DP83867 PHY datasheet says: T1: Post RESET stabilization time == 195us T3: Hardware configuration pins transition to output drivers == 64us T4: RESET pulse width == 1us So with a little overhead set 'reset-assert-us' to 100us (T4) and 'reset-deassert-us' to 280us (T1+T3). NOTE: The tuning of TI DP83867 phy reset delay is derived from linux upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron pitx-imx8m board). i2c structure on Xilinx Versal evaluation platforms contain a lot of devices but also connection to connectors like SFP. Because of this complicated structure with also all level shifters, i2c muxes, etc. not all devices are able to reliably work on 400kHz even if they are compatible with this speed. That's why set i2c frequency to 100KHz to increase reliability of the i2c bus. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
430 lines
9.6 KiB
Text
430 lines
9.6 KiB
Text
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* dts file for Xilinx ZynqMP Generic System Controller
|
|
*
|
|
* (C) Copyright 2021 - 2022, Xilinx, Inc.
|
|
* (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
|
|
*
|
|
* Michal Simek <michal.simek@amd.com>
|
|
*/
|
|
/dts-v1/;
|
|
|
|
#include "zynqmp.dtsi"
|
|
#include "zynqmp-clk-ccf.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/net/ti-dp83867.h>
|
|
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
|
|
#include <dt-bindings/phy/phy.h>
|
|
|
|
/ {
|
|
model = "ZynqMP Generic System Controller";
|
|
compatible = "xlnx,zynqmp-sc-revB", "xlnx,zynqmp-sc", "xlnx,zynqmp";
|
|
|
|
aliases {
|
|
i2c0 = &i2c0;
|
|
i2c1 = &i2c1;
|
|
mmc0 = &sdhci0;
|
|
mmc1 = &sdhci1;
|
|
nvmem0 = &eeprom;
|
|
rtc0 = &rtc;
|
|
serial0 = &uart0;
|
|
serial1 = &uart1;
|
|
serial2 = &dcc;
|
|
spi0 = &qspi;
|
|
spi1 = &spi0;
|
|
spi2 = &spi1;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "earlycon";
|
|
stdout-path = "serial1:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x0 0x0 0x80000000>;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
autorepeat;
|
|
fwuen {
|
|
label = "sw16";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_MISC>;
|
|
wakeup-source;
|
|
autorepeat;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
ds40-led {
|
|
label = "heartbeat";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
ds44-led {
|
|
label = "status";
|
|
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
si5332_2: si5332_2 { /* u42 */
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <26000000>;
|
|
};
|
|
|
|
pwm-fan {
|
|
compatible = "pwm-fan";
|
|
status = "okay";
|
|
pwms = <&ttc0 2 40000 1>;
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
|
|
"QSPI_CS_B", "", "LED1", "LED2", "", /* 5 - 9 */
|
|
"", "ZU4_TRIGGER", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
|
|
"EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
|
|
"EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "I2C1_SCL", /* 20 - 24 */
|
|
"I2C1_SDA", "UART0_RXD", "UART0_TXD", "", "", /* 25 - 29 */
|
|
"", "", "", "", "I2C0_SCL", /* 30 - 34 */
|
|
"I2C0_SDA", "UART1_TXD", "UART1_RXD", "GEM_TX_CLK", "GEM_TX_D0", /* 35 - 39 */
|
|
"GEM_TX_D1", "GEM_TX_D2", "GEM_TX_D3", "GEM_TX_CTL", "GEM_RX_CLK", /* 40 - 44 */
|
|
"GEM_RX_D0", "GEM_RX_D1", "GEM_RX_D2", "GEM_RX_D3", "GEM_RX_CTL", /* 45 - 49 */
|
|
"GEM_MDC", "GEM_MDIO", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
|
|
"USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
|
|
"USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */
|
|
"", "", "", "", "", /* 65 - 69 */
|
|
"", "", "", "", "", /* 70 - 74 */
|
|
"", "", "ETH_RESET_B", /* 75 - 77, MIO end and EMIO start */
|
|
"", "", /* 78 - 79 */
|
|
"", "", "", "", "", /* 80 - 84 */
|
|
"", "", "", "", "", /* 85 -89 */
|
|
"", "", "", "", "", /* 90 - 94 */
|
|
"", "", "", "", "", /* 95 - 99 */
|
|
"", "", "", "", "", /* 100 - 104 */
|
|
"", "", "", "", "", /* 105 - 109 */
|
|
"", "", "", "", "", /* 110 - 114 */
|
|
"", "", "", "", "", /* 115 - 119 */
|
|
"", "", "", "", "", /* 120 - 124 */
|
|
"", "", "", "", "", /* 125 - 129 */
|
|
"", "", "", "", "", /* 130 - 134 */
|
|
"", "", "", "", "", /* 135 - 139 */
|
|
"", "", "", "", "", /* 140 - 144 */
|
|
"", "", "", "", "", /* 145 - 149 */
|
|
"", "", "", "", "", /* 150 - 154 */
|
|
"", "", "", "", "", /* 155 - 159 */
|
|
"", "", "", "", "", /* 160 - 164 */
|
|
"", "", "", "", "", /* 165 - 169 */
|
|
"", "", "", ""; /* 170 - 173 */
|
|
};
|
|
|
|
&gem1 { /* gem1 MIO38-49, MDIO MIO50/51 */
|
|
status = "okay";
|
|
phy-mode = "rgmii-id";
|
|
phy-handle = <&phy0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_gem1_default>;
|
|
|
|
mdio: mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: ethernet-phy@1 {
|
|
#phy-cells = <1>;
|
|
compatible = "ethernet-phy-id2000.a231";
|
|
reg = <1>;
|
|
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
|
|
ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
|
|
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
|
|
ti,dp83867-rxctrl-strap-quirk;
|
|
reset-gpios = <&gpio 77 GPIO_ACTIVE_LOW>;
|
|
reset-assert-us = <100>;
|
|
reset-deassert-us = <280>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c0_default>;
|
|
pinctrl-1 = <&pinctrl_i2c0_gpio>;
|
|
scl-gpios = <&gpio 34 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio 35 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
};
|
|
|
|
&i2c1 { /* i2c1 MIO 24-25 */
|
|
status = "okay";
|
|
bootph-all;
|
|
clock-frequency = <100000>;
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c1_default>;
|
|
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
|
scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
|
/* Use for storing information about SC board */
|
|
eeprom: eeprom@54 { /* u34 - m24128 16kB */
|
|
compatible = "st,24c128", "atmel,24c128";
|
|
reg = <0x54>; /* & 0x5c */
|
|
bootph-all;
|
|
};
|
|
};
|
|
|
|
/* USB 3.0 only */
|
|
&psgtr {
|
|
status = "okay";
|
|
/* nc, nc, usb3 */
|
|
clocks = <&si5332_2>;
|
|
clock-names = "ref2";
|
|
};
|
|
|
|
&qspi { /* MIO 0-5 */
|
|
status = "okay";
|
|
/* QSPI should also have PINCTRL setup */
|
|
flash@0 {
|
|
compatible = "mt25qu512a", "m25p80", "jedec,spi-nor"; /* mt25qu512abb8e12 512Mib */
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-max-frequency = <40000000>; /* 40MHz */
|
|
partition@0 {
|
|
label = "Image Selector";
|
|
reg = <0x0 0x80000>; /* 512KB */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@80000 {
|
|
label = "Image Selector Golden";
|
|
reg = <0x80000 0x80000>; /* 512KB */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@100000 {
|
|
label = "Persistent Register";
|
|
reg = <0x100000 0x20000>; /* 128KB */
|
|
};
|
|
partition@120000 {
|
|
label = "Persistent Register Backup";
|
|
reg = <0x120000 0x20000>; /* 128KB */
|
|
};
|
|
partition@140000 {
|
|
label = "Open_1";
|
|
reg = <0x140000 0xC0000>; /* 768KB */
|
|
};
|
|
partition@200000 {
|
|
label = "Image A (FSBL, PMU, ATF, U-Boot)";
|
|
reg = <0x200000 0xD00000>; /* 13MB */
|
|
};
|
|
partition@f00000 {
|
|
label = "ImgSel Image A Catch";
|
|
reg = <0xF00000 0x80000>; /* 512KB */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@f80000 {
|
|
label = "Image B (FSBL, PMU, ATF, U-Boot)";
|
|
reg = <0xF80000 0xD00000>; /* 13MB */
|
|
};
|
|
partition@1c80000 {
|
|
label = "ImgSel Image B Catch";
|
|
reg = <0x1C80000 0x80000>; /* 512KB */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@1d00000 {
|
|
label = "Open_2";
|
|
reg = <0x1D00000 0x100000>; /* 1MB */
|
|
};
|
|
partition@1e00000 {
|
|
label = "Recovery Image";
|
|
reg = <0x1E00000 0x200000>; /* 2MB */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@2000000 {
|
|
label = "Recovery Image Backup";
|
|
reg = <0x2000000 0x200000>; /* 2MB */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@2200000 {
|
|
label = "U-Boot storage variables";
|
|
reg = <0x2200000 0x20000>; /* 128KB */
|
|
};
|
|
partition@2220000 {
|
|
label = "U-Boot storage variables backup";
|
|
reg = <0x2220000 0x20000>; /* 128KB */
|
|
};
|
|
partition@2240000 {
|
|
label = "SHA256";
|
|
reg = <0x2240000 0x40000>; /* 256B but 256KB sector */
|
|
read-only;
|
|
lock;
|
|
};
|
|
partition@2280000 {
|
|
label = "Secure OS Storage";
|
|
reg = <0x2280000 0x20000>; /* 128KB */
|
|
};
|
|
partition@22A0000 {
|
|
label = "User";
|
|
reg = <0x22A0000 0x1d60000>; /* 29.375 MB */
|
|
};
|
|
};
|
|
};
|
|
|
|
&sdhci0 { /* emmc MIO 13-23 - with some settings MTFC16GAPALBH 16GB */
|
|
status = "okay";
|
|
non-removable;
|
|
disable-wp;
|
|
bus-width = <8>;
|
|
xlnx,mio-bank = <0>;
|
|
};
|
|
|
|
&ttc0 {
|
|
status = "okay";
|
|
#pwm-cells = <3>;
|
|
};
|
|
|
|
&uart1 { /* uart0 MIO36-37 */
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart1_default>;
|
|
};
|
|
|
|
&pinctrl0 { /* required by spec */
|
|
status = "okay";
|
|
|
|
pinctrl_uart1_default: uart1-default {
|
|
conf {
|
|
groups = "uart1_9_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO37";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO36";
|
|
bias-disable;
|
|
};
|
|
|
|
mux {
|
|
groups = "uart1_9_grp";
|
|
function = "uart1";
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c0_default: i2c0-default {
|
|
mux {
|
|
groups = "i2c0_8_grp";
|
|
function = "i2c0";
|
|
};
|
|
|
|
conf {
|
|
groups = "i2c0_8_grp";
|
|
bias-pull-up;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c0_gpio: i2c0-gpio {
|
|
mux {
|
|
groups = "gpio0_34_grp", "gpio0_35_grp";
|
|
function = "gpio0";
|
|
};
|
|
|
|
conf {
|
|
groups = "gpio0_34_grp", "gpio0_35_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c1_default: i2c1-default {
|
|
conf {
|
|
groups = "i2c1_6_grp";
|
|
bias-pull-up;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
mux {
|
|
groups = "i2c1_6_grp";
|
|
function = "i2c1";
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c1_gpio: i2c1-gpio {
|
|
conf {
|
|
groups = "gpio0_24_grp", "gpio0_25_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
mux {
|
|
groups = "gpio0_24_grp", "gpio0_25_grp";
|
|
function = "gpio0";
|
|
};
|
|
};
|
|
|
|
pinctrl_gem1_default: gem1-default {
|
|
conf {
|
|
groups = "ethernet1_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO44", "MIO46", "MIO48";
|
|
bias-high-impedance;
|
|
low-power-disable;
|
|
};
|
|
|
|
conf-bootstrap {
|
|
pins = "MIO45", "MIO47", "MIO49";
|
|
bias-disable;
|
|
low-power-disable;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO38", "MIO39", "MIO40",
|
|
"MIO41", "MIO42", "MIO43";
|
|
bias-disable;
|
|
low-power-enable;
|
|
};
|
|
|
|
conf-mdio {
|
|
groups = "mdio1_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
bias-disable;
|
|
};
|
|
|
|
mux-mdio {
|
|
function = "mdio1";
|
|
groups = "mdio1_0_grp";
|
|
};
|
|
|
|
mux {
|
|
function = "ethernet1";
|
|
groups = "ethernet1_0_grp";
|
|
};
|
|
};
|
|
};
|