u-boot/cpu/pxa/serial.c
Markus Klotzbücher e0269579a5 This is the first commit for the u-boot zylonite port. The following has be
done so far:

	* created zylonite board dir (based on lubbock)
	* extended some - but not all pxa sources and headers for Intel
	  Monahans support (CONFIG_CPU_MONAHANS)
	* created Makefile zylonite target + MAKEALL entry
	* added some debug nonsense, remove later, grep for mk@tbd

Status: compiles (eldk-4.0), and can be started with BDI, but runs forever
	and doesn't halt at breakpoints. Hmmm...
2006-02-07 20:04:48 +01:00

198 lines
4.4 KiB
C

/*
* (C) Copyright 2002
* Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Alex Zuepke <azu@sysgo.de>
*
* Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <common.h>
#include <watchdog.h>
#include <asm/arch/pxa-regs.h>
void serial_setbrg (void)
{
DECLARE_GLOBAL_DATA_PTR;
unsigned int quot = 0;
if (gd->baudrate == 1200)
quot = 768;
else if (gd->baudrate == 9600)
quot = 96;
else if (gd->baudrate == 19200)
quot = 48;
else if (gd->baudrate == 38400)
quot = 24;
else if (gd->baudrate == 57600)
quot = 16;
else if (gd->baudrate == 115200)
quot = 8;
else
hang ();
#ifdef CONFIG_FFUART
#ifdef CONFIG_CPU_MONAHANS
CKENA |= CKENA_22_FFUART;
#else
CKEN |= CKEN6_FFUART;
#endif /* CONFIG_CPU_MONAHANS */
FFIER = 0; /* Disable for now */
FFFCR = 0; /* No fifos enabled */
/* set baud rate */
FFLCR = LCR_WLS0 | LCR_WLS1 | LCR_DLAB;
FFDLL = quot & 0xff;
FFDLH = quot >> 8;
FFLCR = LCR_WLS0 | LCR_WLS1;
FFIER = IER_UUE; /* Enable FFUART */
#elif defined(CONFIG_BTUART)
#ifdef CONFIG_CPU_MONAHANS
CKENA |= CKENA_21_BTUART;
#else
CKEN |= CKEN7_BTUART;
#endif /* CONFIG_CPU_MONAHANS */
BTIER = 0;
BTFCR = 0;
/* set baud rate */
BTLCR = LCR_DLAB;
BTDLL = quot & 0xff;
BTDLH = quot >> 8;
BTLCR = LCR_WLS0 | LCR_WLS1;
BTIER = IER_UUE; /* Enable BFUART */
#elif defined(CONFIG_STUART)
#ifdef CONFIG_CPU_MONAHANS
CKENA |= CKENA_23_STUART;
#else
CKEN |= CKEN5_STUART;
#endif /* CONFIG_CPU_MONAHANS */
STIER = 0;
STFCR = 0;
/* set baud rate */
STLCR = LCR_DLAB;
STDLL = quot & 0xff;
STDLH = quot >> 8;
STLCR = LCR_WLS0 | LCR_WLS1;
STIER = IER_UUE; /* Enable STUART */
#else
#error "Bad: you didn't configure serial ..."
#endif
}
/*
* Initialise the serial port with the given baudrate. The settings
* are always 8 data bits, no parity, 1 stop bit, no start bits.
*
*/
int serial_init (void)
{
serial_setbrg ();
return (0);
}
/*
* Output a single byte to the serial port.
*/
void serial_putc (const char c)
{
#ifdef CONFIG_FFUART
/* wait for room in the tx FIFO on FFUART */
while ((FFLSR & LSR_TEMT) == 0)
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
FFTHR = c;
#elif defined(CONFIG_BTUART)
while ((BTLSR & LSR_TEMT ) == 0 )
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
BTTHR = c;
#elif defined(CONFIG_STUART)
while ((STLSR & LSR_TEMT ) == 0 )
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
STTHR = c;
#endif
/* If \n, also do \r */
if (c == '\n')
serial_putc ('\r');
}
/*
* Read a single byte from the serial port. Returns 1 on success, 0
* otherwise. When the function is succesfull, the character read is
* written into its argument c.
*/
int serial_tstc (void)
{
#ifdef CONFIG_FFUART
return FFLSR & LSR_DR;
#elif defined(CONFIG_BTUART)
return BTLSR & LSR_DR;
#elif defined(CONFIG_STUART)
return STLSR & LSR_DR;
#endif
}
/*
* Read a single byte from the serial port. Returns 1 on success, 0
* otherwise. When the function is succesfull, the character read is
* written into its argument c.
*/
int serial_getc (void)
{
#ifdef CONFIG_FFUART
while (!(FFLSR & LSR_DR))
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
return (char) FFRBR & 0xff;
#elif defined(CONFIG_BTUART)
while (!(BTLSR & LSR_DR))
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
return (char) BTRBR & 0xff;
#elif defined(CONFIG_STUART)
while (!(STLSR & LSR_DR))
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
return (char) STRBR & 0xff;
#endif
}
void
serial_puts (const char *s)
{
while (*s) {
serial_putc (*s++);
}
}