u-boot/drivers/mtd/spi/sf_internal.h
Vignesh R 778572d7cb mtd: spi: Add lightweight SPI flash stack for SPL
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.

Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30

101 lines
3 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* SPI flash internal definitions
*
* Copyright (C) 2008 Atmel Corporation
* Copyright (C) 2013 Jagannadha Sutradharudu Teki, Xilinx Inc.
*/
#ifndef _SF_INTERNAL_H_
#define _SF_INTERNAL_H_
#include <linux/types.h>
#include <linux/compiler.h>
#define SPI_NOR_MAX_ID_LEN 6
#define SPI_NOR_MAX_ADDR_WIDTH 4
struct flash_info {
#if !CONFIG_IS_ENABLED(SPI_FLASH_TINY)
char *name;
#endif
/*
* This array stores the ID bytes.
* The first three bytes are the JEDIC ID.
* JEDEC ID zero means "no ID" (mostly older chips).
*/
u8 id[SPI_NOR_MAX_ID_LEN];
u8 id_len;
/* The size listed here is what works with SPINOR_OP_SE, which isn't
* necessarily called a "sector" by the vendor.
*/
unsigned int sector_size;
u16 n_sectors;
u16 page_size;
u16 addr_width;
u16 flags;
#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
#define SST_WRITE BIT(2) /* use SST byte programming */
#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
#define USE_FSR BIT(7) /* use flag status register */
#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
#define SPI_NOR_HAS_TB BIT(9) /*
* Flash SR has Top/Bottom (TB) protect
* bit. Must be used with
* SPI_NOR_HAS_LOCK.
*/
#define SPI_S3AN BIT(10) /*
* Xilinx Spartan 3AN In-System Flash
* (MFR cannot be used for probing
* because it has the same value as
* ATMEL flashes)
*/
#define SPI_NOR_4B_OPCODES BIT(11) /*
* Use dedicated 4byte address op codes
* to support memory size above 128Mib.
*/
#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
#define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */
#define USE_CLSR BIT(14) /* use CLSR command */
};
extern const struct flash_info spi_nor_ids[];
#define JEDEC_MFR(info) ((info)->id[0])
#define JEDEC_ID(info) (((info)->id[1]) << 8 | ((info)->id[2]))
/* Send a single-byte command to the device and read the response */
int spi_flash_cmd(struct spi_slave *spi, u8 cmd, void *response, size_t len);
/*
* Send a multi-byte command to the device and read the response. Used
* for flash array reads, etc.
*/
int spi_flash_cmd_read(struct spi_slave *spi, const u8 *cmd,
size_t cmd_len, void *data, size_t data_len);
/*
* Send a multi-byte command to the device followed by (optional)
* data. Used for programming the flash array, etc.
*/
int spi_flash_cmd_write(struct spi_slave *spi, const u8 *cmd, size_t cmd_len,
const void *data, size_t data_len);
/* Get software write-protect value (BP bits) */
int spi_flash_cmd_get_sw_write_prot(struct spi_flash *flash);
#ifdef CONFIG_SPI_FLASH_MTD
int spi_flash_mtd_register(struct spi_flash *flash);
void spi_flash_mtd_unregister(void);
#endif
#endif /* _SF_INTERNAL_H_ */