mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 19:10:13 +00:00
51050ff0a2
Currently both pirq_reg_to_linkno() and pirq_linkno_to_reg() assume consecutive PIRQ routing control registers. But this is not always the case on some platforms. Introduce a new device tree property intel,pirq-regmap to describe how the PIRQ routing register offset is mapped to the link number and adjust the irq router driver to utilize the mapping. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
61 lines
2.8 KiB
Text
61 lines
2.8 KiB
Text
Intel Interrupt Router Device Binding
|
|
=====================================
|
|
|
|
The device tree node which describes the operation of the Intel Interrupt Router
|
|
device is as follows:
|
|
|
|
Required properties :
|
|
- reg : Specifies the interrupt router's PCI configuration space address as
|
|
defined by the Open Firmware spec.
|
|
- compatible = "intel,irq-router"
|
|
- intel,pirq-config : Specifies the IRQ routing register programming mechanism.
|
|
Valid values are:
|
|
"pci": IRQ routing is controlled by PCI configuration registers
|
|
"ibase": IRQ routing is in the memory-mapped IBASE register block
|
|
- intel,ibase-offset : IBASE register offset in the interrupt router's PCI
|
|
configuration space, required only if intel,pirq-config = "ibase".
|
|
- intel,actl-8bit : If ACTL (ACPI control) register width is 8-bit, this must
|
|
be specified. The 8-bit ACTL register is seen on ICH series chipset, like
|
|
ICH9/Panther Point/etc. On Atom chipset it is a 32-bit register.
|
|
- intel,actl-addr : ACTL (ACPI control) register offset. ACTL can be either
|
|
in the interrupt router's PCI configuration space, or IBASE.
|
|
- intel,pirq-link : Specifies the PIRQ link information with two cells. The
|
|
first cell is the register offset that controls the first PIRQ link routing.
|
|
The second cell is the total number of PIRQ links the router supports.
|
|
- intel,pirq-regmap : Specifies PIRQ routing register offset of all PIRQ links,
|
|
encoded as 2 cells a group for each link. The first cell is the PIRQ link
|
|
number (0 for PIRQA, 1 for PIRQB, etc). The second cell is the PIRQ routing
|
|
register offset from the interrupt router's base address. If this property
|
|
is omitted, it indicates a consecutive register offset from the first PIRQ
|
|
link, as specified by the first cell of intel,pirq-link.
|
|
- intel,pirq-mask : Specifies the IRQ mask representing the 16 IRQs in the
|
|
8259 PIC. Bit N is 1 means IRQ N is available to be routed.
|
|
- intel,pirq-routing : Specifies all PCI devices' IRQ routing information,
|
|
encoded as 3 cells a group for a device. The first cell is the device's PCI
|
|
bus number, device number and function number encoding with PCI_BDF() macro.
|
|
The second cell is the PCI interrupt pin used by this device. The last cell
|
|
is which PIRQ line the PCI interrupt pin is routed to.
|
|
|
|
|
|
Example
|
|
-------
|
|
|
|
#include <dt-bindings/interrupt-router/intel-irq.h>
|
|
|
|
irq-router@1f,0 {
|
|
reg = <0x0000f800 0 0 0 0>;
|
|
compatible = "intel,irq-router";
|
|
intel,pirq-config = "pci";
|
|
intel,pirq-link = <0x60 8>;
|
|
intel,pirq-mask = <0xdef8>;
|
|
intel,pirq-routing = <
|
|
PCI_BDF(0, 2, 0) INTA PIRQA
|
|
PCI_BDF(0, 3, 0) INTA PIRQB
|
|
PCI_BDF(0, 8, 0) INTA PIRQC
|
|
PCI_BDF(0, 8, 1) INTB PIRQD
|
|
PCI_BDF(1, 6, 0) INTA PIRQE
|
|
PCI_BDF(1, 6, 1) INTB PIRQF
|
|
PCI_BDF(1, 6, 2) INTC PIRQG
|
|
PCI_BDF(1, 6, 3) INTD PIRQH
|
|
>;
|
|
};
|