mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-19 11:18:28 +00:00
25f6dc8955
The 'reset' command did not work on Porter because the reset code was accessing the wrong PMIC address over broken I2C bus driver. Replace the code with DM-aware code and fix up the PMIC address. This makes the 'reset' command work again. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
160 lines
3.1 KiB
C
160 lines
3.1 KiB
C
/*
|
|
* board/renesas/porter/porter.c
|
|
*
|
|
* Copyright (C) 2015 Renesas Electronics Corporation
|
|
* Copyright (C) 2015 Cogent Embedded, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <dm.h>
|
|
#include <dm/platform_data/serial_sh.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/io.h>
|
|
#include <linux/errno.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/arch/rmobile.h>
|
|
#include <asm/arch/rcar-mstp.h>
|
|
#include <asm/arch/sh_sdhi.h>
|
|
#include <netdev.h>
|
|
#include <miiphy.h>
|
|
#include <i2c.h>
|
|
#include <div64.h>
|
|
#include "qos.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define CLK2MHZ(clk) (clk / 1000 / 1000)
|
|
void s_init(void)
|
|
{
|
|
struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
|
|
struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
|
|
u32 stc;
|
|
|
|
/* Watchdog init */
|
|
writel(0xA5A5A500, &rwdt->rwtcsra);
|
|
writel(0xA5A5A500, &swdt->swtcsra);
|
|
|
|
/* CPU frequency setting. Set to 1.5GHz */
|
|
stc = ((1500 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) << PLL0_STC_BIT;
|
|
clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc);
|
|
|
|
/* QoS */
|
|
qos_init();
|
|
}
|
|
|
|
#define TMU0_MSTP125 BIT(25)
|
|
|
|
#define SD2CKCR 0xE615026C
|
|
#define SD_97500KHZ 0x7
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
|
|
|
|
/*
|
|
* SD0 clock is set to 97.5MHz by default.
|
|
* Set SD2 to the 97.5MHz as well.
|
|
*/
|
|
writel(SD_97500KHZ, SD2CKCR);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define ETHERNET_PHY_RESET 176 /* GPIO 5 22 */
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
/* Force ethernet PHY out of reset */
|
|
gpio_request(ETHERNET_PHY_RESET, "phy_reset");
|
|
gpio_direction_output(ETHERNET_PHY_RESET, 0);
|
|
mdelay(10);
|
|
gpio_direction_output(ETHERNET_PHY_RESET, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
if (fdtdec_setup_memory_size() != 0)
|
|
return -EINVAL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init_banksize(void)
|
|
{
|
|
fdtdec_setup_memory_banksize();
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* porter has KSZ8041RNLI */
|
|
#define PHY_CONTROL1 0x1E
|
|
#define PHY_LED_MODE 0xC0000
|
|
#define PHY_LED_MODE_ACK 0x4000
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
|
|
ret &= ~PHY_LED_MODE;
|
|
ret |= PHY_LED_MODE_ACK;
|
|
ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
|
|
|
|
return 0;
|
|
}
|
|
|
|
const struct rmobile_sysinfo sysinfo = {
|
|
CONFIG_ARCH_RMOBILE_BOARD_STRING
|
|
};
|
|
|
|
void reset_cpu(ulong addr)
|
|
{
|
|
struct udevice *dev;
|
|
const u8 pmic_bus = 6;
|
|
const u8 pmic_addr = 0x5a;
|
|
u8 data;
|
|
int ret;
|
|
|
|
ret = i2c_get_chip_for_busnum(pmic_bus, pmic_addr, 1, &dev);
|
|
if (ret)
|
|
hang();
|
|
|
|
ret = dm_i2c_read(dev, 0x13, &data, 1);
|
|
if (ret)
|
|
hang();
|
|
|
|
data |= BIT(1);
|
|
|
|
ret = dm_i2c_write(dev, 0x13, &data, 1);
|
|
if (ret)
|
|
hang();
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#include <spl.h>
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
board_early_init_f();
|
|
}
|
|
|
|
void spl_board_init(void)
|
|
{
|
|
/* UART clocks enabled and gd valid - init serial console */
|
|
preloader_console_init();
|
|
}
|
|
|
|
void board_boot_order(u32 *spl_boot_list)
|
|
{
|
|
/* Boot from SPI NOR with YMODEM UART fallback. */
|
|
spl_boot_list[0] = BOOT_DEVICE_SPI;
|
|
spl_boot_list[1] = BOOT_DEVICE_UART;
|
|
spl_boot_list[2] = BOOT_DEVICE_NONE;
|
|
}
|
|
#endif
|