mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 13:56:30 +00:00
6d0f6bcf33
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
360 lines
8.4 KiB
C
360 lines
8.4 KiB
C
/*
|
|
* genietv/genietv.c
|
|
*
|
|
* The GENIETV is using the following physical memorymap (copied from
|
|
* the FADS configuration):
|
|
*
|
|
* ff020000 -> ff02ffff : pcmcia
|
|
* ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxROM
|
|
* ff000000 -> ff00ffff : IMAP internal in the cpu
|
|
* 02800000 -> 0287ffff : flash connected to CS0
|
|
* 00000000 -> nnnnnnnn : sdram setup by U-Boot
|
|
*
|
|
* CS pins are connected as follows:
|
|
*
|
|
* CS0 -512Kb boot flash
|
|
* CS1 - SDRAM #1
|
|
* CS2 - SDRAM #2
|
|
* CS3 - Flash #1
|
|
* CS4 - Flash #2
|
|
* CS5 - LON (if present)
|
|
* CS6 - PCMCIA #1
|
|
* CS7 - PCMCIA #2
|
|
*
|
|
* Ports are configured as follows:
|
|
*
|
|
* PA7 - SDRAM banks enable
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <mpc8xx.h>
|
|
|
|
#define CONFIG_SYS_PA7 0x0100
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
static long int dram_size (long int, long int *, long int);
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
#define _NOT_USED_ 0xFFFFFFFF
|
|
|
|
const uint sdram_table[] = {
|
|
/*
|
|
* Single Read. (Offset 0 in UPMB RAM)
|
|
*/
|
|
0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBEEC00,
|
|
0x1FFDDC47, /* last */
|
|
/*
|
|
* SDRAM Initialization (offset 5 in UPMB RAM)
|
|
*
|
|
* This is no UPM entry point. The following definition uses
|
|
* the remaining space to establish an initialization
|
|
* sequence, which is executed by a RUN command.
|
|
*
|
|
*/
|
|
0x1FFDDC34, 0xEFEEAC34, 0x1FBD5C35, /* last */
|
|
/*
|
|
* Burst Read. (Offset 8 in UPMB RAM)
|
|
*/
|
|
0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00,
|
|
0xF0AFFC00, 0xF1AFFC00, 0xEFBEEC00, 0x1FFDDC47, /* last */
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
/*
|
|
* Single Write. (Offset 18 in UPMB RAM)
|
|
*/
|
|
0x1F2DFC04, 0xEEAFAC00, 0x01BE4C04, 0x1FFDDC47, /* last */
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
/*
|
|
* Burst Write. (Offset 20 in UPMB RAM)
|
|
*/
|
|
0x1F0DFC04, 0xEEAFAC00, 0x10AF5C00, 0xF0AFFC00,
|
|
0xF0AFFC00, 0xE1BEEC04, 0x1FFDDC47, /* last */
|
|
_NOT_USED_,
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
/*
|
|
* Refresh (Offset 30 in UPMB RAM)
|
|
*/
|
|
0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
|
|
0xFFFFFC84, 0xFFFFFC07, /* last */
|
|
_NOT_USED_, _NOT_USED_,
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
/*
|
|
* Exception. (Offset 3c in UPMB RAM)
|
|
*/
|
|
0x7FFFFC07, /* last */
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
};
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
|
|
/*
|
|
* Check Board Identity
|
|
*/
|
|
|
|
int checkboard (void)
|
|
{
|
|
puts ("Board: GenieTV\n");
|
|
return 0;
|
|
}
|
|
|
|
#if 0
|
|
static void PrintState (void)
|
|
{
|
|
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
|
|
volatile memctl8xx_t *memctl = &im->im_memctl;
|
|
|
|
printf ("\n0 - FLASH: B=%08x O=%08x", memctl->memc_br0,
|
|
memctl->memc_or0);
|
|
printf ("\n1 - SDRAM: B=%08x O=%08x", memctl->memc_br1,
|
|
memctl->memc_or1);
|
|
printf ("\n2 - SDRAM: B=%08x O=%08x", memctl->memc_br2,
|
|
memctl->memc_or2);
|
|
}
|
|
#endif
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
phys_size_t initdram (int board_type)
|
|
{
|
|
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
|
|
volatile memctl8xx_t *memctl = &im->im_memctl;
|
|
long int size_b0, size_b1, size8;
|
|
|
|
/* Enable SDRAM */
|
|
|
|
/* Configuring PA7 for general purpouse output pin */
|
|
im->im_ioport.iop_papar &= ~CONFIG_SYS_PA7; /* 0 = general purpouse */
|
|
im->im_ioport.iop_padir |= CONFIG_SYS_PA7; /* 1 = output */
|
|
|
|
/* Enable SDRAM - PA7 = 1 */
|
|
im->im_ioport.iop_padat |= CONFIG_SYS_PA7; /* value of PA7 */
|
|
|
|
/*
|
|
* Preliminary prescaler for refresh (depends on number of
|
|
* banks): This value is selected for four cycles every 62.4 us
|
|
* with two SDRAM banks or four cycles every 31.2 us with one
|
|
* bank. It will be adjusted after memory sizing.
|
|
*/
|
|
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
|
|
|
|
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL;
|
|
|
|
upmconfig (UPMB, (uint *) sdram_table,
|
|
sizeof (sdram_table) / sizeof (uint));
|
|
|
|
/*
|
|
* Map controller banks 1 and 2 to the SDRAM banks 1 and 2 at
|
|
* preliminary addresses - these have to be modified after the
|
|
* SDRAM size has been determined.
|
|
*/
|
|
|
|
memctl->memc_or1 = 0xF0000000 | CONFIG_SYS_OR_TIMING_SDRAM;
|
|
memctl->memc_br1 =
|
|
((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V);
|
|
|
|
memctl->memc_or2 = 0xF0000000 | CONFIG_SYS_OR_TIMING_SDRAM;
|
|
memctl->memc_br2 =
|
|
((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V);
|
|
|
|
/* perform SDRAM initialization sequence */
|
|
memctl->memc_mar = 0x00000088;
|
|
|
|
memctl->memc_mcr = 0x80802105; /* SDRAM bank 0 */
|
|
|
|
memctl->memc_mcr = 0x80804105; /* SDRAM bank 1 */
|
|
|
|
/* Execute refresh 8 times */
|
|
memctl->memc_mbmr = (CONFIG_SYS_MBMR_8COL & ~MBMR_TLFB_MSK) | MBMR_TLFB_8X;
|
|
|
|
memctl->memc_mcr = 0x80802130; /* SDRAM bank 0 - execute twice */
|
|
|
|
memctl->memc_mcr = 0x80804130; /* SDRAM bank 1 - execute twice */
|
|
|
|
/* Execute refresh 4 times */
|
|
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL;
|
|
|
|
/*
|
|
* Check Bank 0 Memory Size for re-configuration
|
|
*
|
|
* try 8 column mode
|
|
*/
|
|
|
|
#if 0
|
|
PrintState ();
|
|
#endif
|
|
/* printf ("\nChecking bank1..."); */
|
|
size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *) SDRAM_BASE1_PRELIM,
|
|
SDRAM_MAX_SIZE);
|
|
|
|
size_b0 = size8;
|
|
|
|
/* printf ("\nChecking bank2..."); */
|
|
size_b1 =
|
|
dram_size (memctl->memc_mbmr, (long *) SDRAM_BASE2_PRELIM,
|
|
SDRAM_MAX_SIZE);
|
|
|
|
/*
|
|
* Final mapping: map bigger bank first
|
|
*/
|
|
|
|
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
|
|
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
|
|
|
|
if (size_b1 > 0) {
|
|
/*
|
|
* Position Bank 1 immediately above Bank 0
|
|
*/
|
|
memctl->memc_or2 =
|
|
((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
|
|
memctl->memc_br2 =
|
|
((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V) +
|
|
(size_b0 & BR_BA_MSK);
|
|
} else {
|
|
/*
|
|
* No bank 1
|
|
*
|
|
* invalidate bank
|
|
*/
|
|
memctl->memc_br2 = 0;
|
|
/* adjust refresh rate depending on SDRAM type, one bank */
|
|
memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_4K;
|
|
}
|
|
|
|
/* If no memory detected, disable SDRAM */
|
|
if ((size_b0 + size_b1) == 0) {
|
|
printf ("disabling SDRAM!\n");
|
|
/* Disable SDRAM - PA7 = 1 */
|
|
im->im_ioport.iop_padat &= ~CONFIG_SYS_PA7; /* value of PA7 */
|
|
}
|
|
/* else */
|
|
/* printf("done! (%08lx)\n", size_b0 + size_b1); */
|
|
|
|
#if 0
|
|
PrintState ();
|
|
#endif
|
|
return (size_b0 + size_b1);
|
|
}
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
/*
|
|
* Check memory range for valid RAM. A simple memory test determines
|
|
* the actually available RAM size between addresses `base' and
|
|
* `base + maxsize'. Some (not all) hardware errors are detected:
|
|
* - short between address lines
|
|
* - short between data lines
|
|
*/
|
|
|
|
static long int dram_size (long int mbmr_value, long int *base,
|
|
long int maxsize)
|
|
{
|
|
long size;
|
|
|
|
/*memctl->memc_mbmr = mbmr_value; */
|
|
|
|
size = get_ram_size (base, maxsize);
|
|
|
|
if (size) {
|
|
/* printf("(%08lx)", size); */
|
|
} else {
|
|
printf ("(0)");
|
|
}
|
|
|
|
return (size);
|
|
}
|
|
|
|
#if defined(CONFIG_CMD_PCMCIA)
|
|
|
|
#ifdef CONFIG_SYS_PCMCIA_MEM_ADDR
|
|
volatile unsigned char *pcmcia_mem = (unsigned char *) CONFIG_SYS_PCMCIA_MEM_ADDR;
|
|
#endif
|
|
|
|
int pcmcia_init (void)
|
|
{
|
|
volatile pcmconf8xx_t *pcmp;
|
|
uint v, slota, slotb;
|
|
|
|
/*
|
|
** Enable the PCMCIA for a Flash card.
|
|
*/
|
|
pcmp = (pcmconf8xx_t *) (&(((immap_t *) CONFIG_SYS_IMMR)->im_pcmcia));
|
|
|
|
#if 0
|
|
pcmp->pcmc_pbr0 = CONFIG_SYS_PCMCIA_MEM_ADDR;
|
|
pcmp->pcmc_por0 = 0xc00ff05d;
|
|
#endif
|
|
|
|
/* Set all slots to zero by default. */
|
|
pcmp->pcmc_pgcra = 0;
|
|
pcmp->pcmc_pgcrb = 0;
|
|
#ifdef PCMCIA_SLOT_A
|
|
pcmp->pcmc_pgcra = 0x40;
|
|
#endif
|
|
#ifdef PCMCIA_SLOT_B
|
|
pcmp->pcmc_pgcrb = 0x40;
|
|
#endif
|
|
|
|
/* Check if any PCMCIA card is luged in. */
|
|
slota = (pcmp->pcmc_pipr & 0x18000000) == 0;
|
|
slotb = (pcmp->pcmc_pipr & 0x00001800) == 0;
|
|
|
|
if (!(slota || slotb)) {
|
|
printf ("No card present\n");
|
|
#ifdef PCMCIA_SLOT_A
|
|
pcmp->pcmc_pgcra = 0;
|
|
#endif
|
|
#ifdef PCMCIA_SLOT_B
|
|
pcmp->pcmc_pgcrb = 0;
|
|
#endif
|
|
return -1;
|
|
} else
|
|
printf ("Unknown card (");
|
|
|
|
v = 0;
|
|
|
|
switch ((pcmp->pcmc_pipr >> 14) & 3) {
|
|
case 0x00:
|
|
printf ("5V");
|
|
v = 5;
|
|
break;
|
|
case 0x01:
|
|
printf ("5V and 3V");
|
|
v = 3;
|
|
break;
|
|
case 0x03:
|
|
printf ("5V, 3V and x.xV");
|
|
v = 3;
|
|
break;
|
|
}
|
|
|
|
switch (v) {
|
|
case 3:
|
|
printf ("; using 3V");
|
|
/* Enable 3 volt Vcc. */
|
|
|
|
break;
|
|
|
|
default:
|
|
printf ("; unknown voltage");
|
|
return -1;
|
|
}
|
|
printf (")\n");
|
|
/* disable pcmcia reset after a while */
|
|
|
|
udelay (20);
|
|
|
|
pcmp->pcmc_pgcrb = 0;
|
|
|
|
/* If you using a real hd you should give a short
|
|
* spin-up time. */
|
|
#ifdef CONFIG_DISK_SPINUP_TIME
|
|
udelay (CONFIG_DISK_SPINUP_TIME);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
#endif
|