mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 23:47:24 +00:00
00f43e51c5
mx6sabre boards can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the eMMC changes depending on the kernel version. In order to avoid such issue, use UUID method to specify the rootfs location. Succesfully tested booting a NXP 4.1 and also a mainline kernel on a mx6qsabresd and mx6dlsabreauto. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
80 lines
2.3 KiB
C
80 lines
2.3 KiB
C
/*
|
|
* Copyright (C) 2012 Freescale Semiconductor, Inc.
|
|
*
|
|
* Configuration settings for the Freescale i.MX6Q SabreAuto board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __MX6SABREAUTO_CONFIG_H
|
|
#define __MX6SABREAUTO_CONFIG_H
|
|
|
|
#ifdef CONFIG_SPL
|
|
#include "imx6_spl.h"
|
|
#endif
|
|
|
|
#define CONFIG_MACH_TYPE 3529
|
|
#define CONFIG_MXC_UART_BASE UART4_BASE
|
|
#define CONSOLE_DEV "ttymxc3"
|
|
|
|
/* USB Configs */
|
|
#define CONFIG_USB_HOST_ETHER
|
|
#define CONFIG_USB_ETHER_ASIX
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} }
|
|
|
|
#include "mx6sabre_common.h"
|
|
|
|
#ifdef CONFIG_MTD_NOR_FLASH
|
|
#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
|
|
#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024)
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
|
#endif
|
|
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 2
|
|
#if defined(CONFIG_ENV_IS_IN_MMC)
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#endif
|
|
|
|
/* I2C Configs */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MXC
|
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
/* NAND flash command */
|
|
#define CONFIG_CMD_NAND
|
|
#define CONFIG_CMD_NAND_TRIMFFS
|
|
|
|
/* NAND stuff */
|
|
#define CONFIG_NAND_MXS
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE 0x40000000
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
|
|
/* DMA stuff, needed for GPMI/MXS NAND support */
|
|
#define CONFIG_APBH_DMA
|
|
#define CONFIG_APBH_DMA_BURST
|
|
#define CONFIG_APBH_DMA_BURST8
|
|
|
|
/* PMIC */
|
|
#define CONFIG_POWER
|
|
#define CONFIG_POWER_I2C
|
|
#define CONFIG_POWER_PFUZE100
|
|
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
|
|
|
|
#endif /* __MX6SABREAUTO_CONFIG_H */
|