mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-15 07:43:07 +00:00
aae0e68909
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}
A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.
For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
63 lines
2.9 KiB
Text
63 lines
2.9 KiB
Text
This file contains information for VSC9953, a Vitesse L2 Switch IP
|
|
which is integrated in the T1040/T1020 Freescale SoCs.
|
|
|
|
About Device:
|
|
=============
|
|
VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
|
|
- 8192 MAC addresses
|
|
- Static Address provisioning
|
|
- Dynamic learning of MAC addresses and aging
|
|
- 4096 VLANs
|
|
- Independent and shared VLAN learning (IVL, SVL)
|
|
- Policing with storm control and MC/BC protection
|
|
- IPv4 and IPv6 multicast
|
|
- Jumbo frames (9.6 KB)
|
|
- Access Control List
|
|
- VLAN editing, translation and remarking
|
|
- RMON counters per port
|
|
|
|
Switch interfaces:
|
|
- 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
|
|
- 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
|
|
to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
|
|
|
|
Commands Overview:
|
|
=============
|
|
Commands supported
|
|
- enable/disable a port or show its configuration (speed, duplexity, status, etc.)
|
|
- port statistics
|
|
- MAC learning
|
|
- add/remove FDB entries
|
|
- Port-based VLAN
|
|
- Private/Shared VLAN learning
|
|
- VLAN ingress filtering
|
|
- Port LAG
|
|
|
|
Commands syntax
|
|
ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration
|
|
ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics
|
|
ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port
|
|
ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries;
|
|
if [vlan <vid>] is missing, VID 1 will be used
|
|
ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port
|
|
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members)
|
|
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port
|
|
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag.
|
|
Tag's VID could be the frame's classified VID or the PVID of the port
|
|
ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private
|
|
ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port
|
|
ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port
|
|
|
|
=> ethsw show
|
|
Port Status Link Speed Duplex
|
|
0 enabled down 10 half
|
|
1 enabled down 10 half
|
|
2 enabled down 10 half
|
|
3 enabled up 1000 full
|
|
4 disabled down - half
|
|
5 disabled down - half
|
|
6 disabled down - half
|
|
7 disabled down - half
|
|
8 enabled up 2500 full
|
|
9 enabled up 2500 full
|
|
=>
|