u-boot/board/ti/ti814x/evm.c
Mugunthan V N 9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00

188 lines
4 KiB
C

/*
* evm.c
*
* Board functions for TI814x EVM
*
* Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <cpsw.h>
#include <errno.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include "evm.h"
DECLARE_GLOBAL_DATA_PTR;
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
/* UART Defines */
#ifdef CONFIG_SPL_BUILD
static const struct cmd_control evm_ddr2_cctrl_data = {
.cmd0csratio = 0x80,
.cmd0iclkout = 0x00,
.cmd1csratio = 0x80,
.cmd1iclkout = 0x00,
.cmd2csratio = 0x80,
.cmd2iclkout = 0x00,
};
static const struct emif_regs evm_ddr2_emif0_regs = {
.sdram_config = 0x40801ab2,
.ref_ctrl = 0x10000c30,
.sdram_tim1 = 0x0aaaf552,
.sdram_tim2 = 0x043631d2,
.sdram_tim3 = 0x00000327,
.emif_ddr_phy_ctlr_1 = 0x00000007
};
static const struct emif_regs evm_ddr2_emif1_regs = {
.sdram_config = 0x40801ab2,
.ref_ctrl = 0x10000c30,
.sdram_tim1 = 0x0aaaf552,
.sdram_tim2 = 0x043631d2,
.sdram_tim3 = 0x00000327,
.emif_ddr_phy_ctlr_1 = 0x00000007
};
const struct dmm_lisa_map_regs evm_lisa_map_regs = {
.dmm_lisa_map_0 = 0x00000000,
.dmm_lisa_map_1 = 0x00000000,
.dmm_lisa_map_2 = 0x806c0300,
.dmm_lisa_map_3 = 0x806c0300,
};
static const struct ddr_data evm_ddr2_data = {
.datardsratio0 = ((0x35<<10) | (0x35<<0)),
.datawdsratio0 = ((0x20<<10) | (0x20<<0)),
.datawiratio0 = ((0<<10) | (0<<0)),
.datagiratio0 = ((0<<10) | (0<<0)),
.datafwsratio0 = ((0x90<<10) | (0x90<<0)),
.datawrsratio0 = ((0x50<<10) | (0x50<<0)),
};
void set_uart_mux_conf(void)
{
/* Set UART pins */
enable_uart0_pin_mux();
}
void set_mux_conf_regs(void)
{
/* Set MMC pins */
enable_mmc1_pin_mux();
/* Set Ethernet pins */
enable_enet_pin_mux();
}
void sdram_init(void)
{
config_dmm(&evm_lisa_map_regs);
config_ddr(0, NULL, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif0_regs, 0);
config_ddr(0, NULL, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif1_regs, 1);
}
#endif
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
return 0;
}
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
int board_mmc_init(bd_t *bis)
{
omap_mmc_init(1, 0, 0, -1, -1);
return 0;
}
#endif
#ifdef CONFIG_DRIVER_TI_CPSW
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slaves[] = {
{
.slave_reg_ofs = 0x50,
.sliver_reg_ofs = 0x700,
.phy_addr = 1,
},
{
.slave_reg_ofs = 0x90,
.sliver_reg_ofs = 0x740,
.phy_addr = 0,
},
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x100,
.slaves = 1,
.slave_data = cpsw_slaves,
.ale_reg_ofs = 0x600,
.ale_entries = 1024,
.host_port_reg_ofs = 0x28,
.hw_stats_reg_ofs = 0x400,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_1,
};
#endif
int board_eth_init(bd_t *bis)
{
uint8_t mac_addr[6];
uint32_t mac_hi, mac_lo;
if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
printf("<ethaddr> not set. Reading from E-fuse\n");
/* try reading mac address from efuse */
mac_lo = readl(&cdev->macid0l);
mac_hi = readl(&cdev->macid0h);
mac_addr[0] = mac_hi & 0xFF;
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
mac_addr[4] = mac_lo & 0xFF;
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
if (is_valid_ether_addr(mac_addr))
eth_setenv_enetaddr("ethaddr", mac_addr);
else
printf("Unable to read MAC address. Set <ethaddr>\n");
}
return cpsw_register(&cpsw_data);
}