u-boot/drivers/i2c/fsl_i2c.c
Shaveta Leekha a405764c1e drivers/i2c/fsl_i2c: modify i2c_read to handle multi-byte write
Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"

However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
        RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.

Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.

To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-04-29 07:10:58 +02:00

541 lines
14 KiB
C

/*
* Copyright 2006,2009 Freescale Semiconductor, Inc.
*
* 2012, Heiko Schocher, DENX Software Engineering, hs@denx.de.
* Changes for multibus/multiadapter I2C support.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <i2c.h> /* Functional interface */
#include <asm/io.h>
#include <asm/fsl_i2c.h> /* HW definitions */
/* The maximum number of microseconds we will wait until another master has
* released the bus. If not defined in the board header file, then use a
* generic value.
*/
#ifndef CONFIG_I2C_MBB_TIMEOUT
#define CONFIG_I2C_MBB_TIMEOUT 100000
#endif
/* The maximum number of microseconds we will wait for a read or write
* operation to complete. If not defined in the board header file, then use a
* generic value.
*/
#ifndef CONFIG_I2C_TIMEOUT
#define CONFIG_I2C_TIMEOUT 10000
#endif
#define I2C_READ_BIT 1
#define I2C_WRITE_BIT 0
DECLARE_GLOBAL_DATA_PTR;
static const struct fsl_i2c *i2c_dev[2] = {
(struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C_OFFSET),
#ifdef CONFIG_SYS_FSL_I2C2_OFFSET
(struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C2_OFFSET)
#endif
};
/* I2C speed map for a DFSR value of 1 */
/*
* Map I2C frequency dividers to FDR and DFSR values
*
* This structure is used to define the elements of a table that maps I2C
* frequency divider (I2C clock rate divided by I2C bus speed) to a value to be
* programmed into the Frequency Divider Ratio (FDR) and Digital Filter
* Sampling Rate (DFSR) registers.
*
* The actual table should be defined in the board file, and it must be called
* fsl_i2c_speed_map[].
*
* The last entry of the table must have a value of {-1, X}, where X is same
* FDR/DFSR values as the second-to-last entry. This guarantees that any
* search through the array will always find a match.
*
* The values of the divider must be in increasing numerical order, i.e.
* fsl_i2c_speed_map[x+1].divider > fsl_i2c_speed_map[x].divider.
*
* For this table, the values are based on a value of 1 for the DFSR
* register. See the application note AN2919 "Determining the I2C Frequency
* Divider Ratio for SCL"
*
* ColdFire I2C frequency dividers for FDR values are different from
* PowerPC. The protocol to use the I2C module is still the same.
* A different table is defined and are based on MCF5xxx user manual.
*
*/
static const struct {
unsigned short divider;
u8 fdr;
} fsl_i2c_speed_map[] = {
#ifdef __M68K__
{20, 32}, {22, 33}, {24, 34}, {26, 35},
{28, 0}, {28, 36}, {30, 1}, {32, 37},
{34, 2}, {36, 38}, {40, 3}, {40, 39},
{44, 4}, {48, 5}, {48, 40}, {56, 6},
{56, 41}, {64, 42}, {68, 7}, {72, 43},
{80, 8}, {80, 44}, {88, 9}, {96, 41},
{104, 10}, {112, 42}, {128, 11}, {128, 43},
{144, 12}, {160, 13}, {160, 48}, {192, 14},
{192, 49}, {224, 50}, {240, 15}, {256, 51},
{288, 16}, {320, 17}, {320, 52}, {384, 18},
{384, 53}, {448, 54}, {480, 19}, {512, 55},
{576, 20}, {640, 21}, {640, 56}, {768, 22},
{768, 57}, {960, 23}, {896, 58}, {1024, 59},
{1152, 24}, {1280, 25}, {1280, 60}, {1536, 26},
{1536, 61}, {1792, 62}, {1920, 27}, {2048, 63},
{2304, 28}, {2560, 29}, {3072, 30}, {3840, 31},
{-1, 31}
#endif
};
/**
* Set the I2C bus speed for a given I2C device
*
* @param dev: the I2C device
* @i2c_clk: I2C bus clock frequency
* @speed: the desired speed of the bus
*
* The I2C device must be stopped before calling this function.
*
* The return value is the actual bus speed that is set.
*/
static unsigned int set_i2c_bus_speed(const struct fsl_i2c *dev,
unsigned int i2c_clk, unsigned int speed)
{
unsigned short divider = min(i2c_clk / speed, (unsigned short) -1);
/*
* We want to choose an FDR/DFSR that generates an I2C bus speed that
* is equal to or lower than the requested speed. That means that we
* want the first divider that is equal to or greater than the
* calculated divider.
*/
#ifdef __PPC__
u8 dfsr, fdr = 0x31; /* Default if no FDR found */
/* a, b and dfsr matches identifiers A,B and C respectively in AN2919 */
unsigned short a, b, ga, gb;
unsigned long c_div, est_div;
#ifdef CONFIG_FSL_I2C_CUSTOM_DFSR
dfsr = CONFIG_FSL_I2C_CUSTOM_DFSR;
#else
/* Condition 1: dfsr <= 50/T */
dfsr = (5 * (i2c_clk / 1000)) / 100000;
#endif
#ifdef CONFIG_FSL_I2C_CUSTOM_FDR
fdr = CONFIG_FSL_I2C_CUSTOM_FDR;
speed = i2c_clk / divider; /* Fake something */
#else
debug("Requested speed:%d, i2c_clk:%d\n", speed, i2c_clk);
if (!dfsr)
dfsr = 1;
est_div = ~0;
for (ga = 0x4, a = 10; a <= 30; ga++, a += 2) {
for (gb = 0; gb < 8; gb++) {
b = 16 << gb;
c_div = b * (a + ((3*dfsr)/b)*2);
if ((c_div > divider) && (c_div < est_div)) {
unsigned short bin_gb, bin_ga;
est_div = c_div;
bin_gb = gb << 2;
bin_ga = (ga & 0x3) | ((ga & 0x4) << 3);
fdr = bin_gb | bin_ga;
speed = i2c_clk / est_div;
debug("FDR:0x%.2x, div:%ld, ga:0x%x, gb:0x%x, "
"a:%d, b:%d, speed:%d\n",
fdr, est_div, ga, gb, a, b, speed);
/* Condition 2 not accounted for */
debug("Tr <= %d ns\n",
(b - 3 * dfsr) * 1000000 /
(i2c_clk / 1000));
}
}
if (a == 20)
a += 2;
if (a == 24)
a += 4;
}
debug("divider:%d, est_div:%ld, DFSR:%d\n", divider, est_div, dfsr);
debug("FDR:0x%.2x, speed:%d\n", fdr, speed);
#endif
writeb(dfsr, &dev->dfsrr); /* set default filter */
writeb(fdr, &dev->fdr); /* set bus speed */
#else
unsigned int i;
for (i = 0; i < ARRAY_SIZE(fsl_i2c_speed_map); i++)
if (fsl_i2c_speed_map[i].divider >= divider) {
u8 fdr;
fdr = fsl_i2c_speed_map[i].fdr;
speed = i2c_clk / fsl_i2c_speed_map[i].divider;
writeb(fdr, &dev->fdr); /* set bus speed */
break;
}
#endif
return speed;
}
static unsigned int get_i2c_clock(int bus)
{
if (bus)
return gd->arch.i2c2_clk; /* I2C2 clock */
else
return gd->arch.i2c1_clk; /* I2C1 clock */
}
static int fsl_i2c_fixup(const struct fsl_i2c *dev)
{
const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT);
unsigned long long timeval = 0;
int ret = -1;
unsigned int flags = 0;
#ifdef CONFIG_SYS_FSL_ERRATUM_I2C_A004447
unsigned int svr = get_svr();
if ((SVR_SOC_VER(svr) == SVR_8548 && IS_SVR_REV(svr, 3, 1)) ||
(SVR_REV(svr) <= CONFIG_SYS_FSL_A004447_SVR_REV))
flags = I2C_CR_BIT6;
#endif
writeb(I2C_CR_MEN | I2C_CR_MSTA, &dev->cr);
timeval = get_ticks();
while (!(readb(&dev->sr) & I2C_SR_MBB)) {
if ((get_ticks() - timeval) > timeout)
goto err;
}
if (readb(&dev->sr) & I2C_SR_MAL) {
/* SDA is stuck low */
writeb(0, &dev->cr);
udelay(100);
writeb(I2C_CR_MSTA | flags, &dev->cr);
writeb(I2C_CR_MEN | I2C_CR_MSTA | flags, &dev->cr);
}
readb(&dev->dr);
timeval = get_ticks();
while (!(readb(&dev->sr) & I2C_SR_MIF)) {
if ((get_ticks() - timeval) > timeout)
goto err;
}
ret = 0;
err:
writeb(I2C_CR_MEN | flags, &dev->cr);
writeb(0, &dev->sr);
udelay(100);
return ret;
}
static void fsl_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
{
const struct fsl_i2c *dev;
const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT);
unsigned long long timeval;
#ifdef CONFIG_SYS_I2C_INIT_BOARD
/* Call board specific i2c bus reset routine before accessing the
* environment, which might be in a chip on that bus. For details
* about this problem see doc/I2C_Edge_Conditions.
*/
i2c_init_board();
#endif
dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
writeb(0, &dev->cr); /* stop I2C controller */
udelay(5); /* let it shutdown in peace */
set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed);
writeb(slaveadd << 1, &dev->adr);/* write slave address */
writeb(0x0, &dev->sr); /* clear status register */
writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
timeval = get_ticks();
while (readb(&dev->sr) & I2C_SR_MBB) {
if ((get_ticks() - timeval) < timeout)
continue;
if (fsl_i2c_fixup(dev))
debug("i2c_init: BUS#%d failed to init\n",
adap->hwadapnr);
break;
}
#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
/* Call board specific i2c bus reset routine AFTER the bus has been
* initialized. Use either this callpoint or i2c_init_board;
* which is called before i2c_init operations.
* For details about this problem see doc/I2C_Edge_Conditions.
*/
i2c_board_late_init();
#endif
}
static int
i2c_wait4bus(struct i2c_adapter *adap)
{
struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
unsigned long long timeval = get_ticks();
const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT);
while (readb(&dev->sr) & I2C_SR_MBB) {
if ((get_ticks() - timeval) > timeout)
return -1;
}
return 0;
}
static __inline__ int
i2c_wait(struct i2c_adapter *adap, int write)
{
u32 csr;
unsigned long long timeval = get_ticks();
const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT);
struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
do {
csr = readb(&dev->sr);
if (!(csr & I2C_SR_MIF))
continue;
/* Read again to allow register to stabilise */
csr = readb(&dev->sr);
writeb(0x0, &dev->sr);
if (csr & I2C_SR_MAL) {
debug("i2c_wait: MAL\n");
return -1;
}
if (!(csr & I2C_SR_MCF)) {
debug("i2c_wait: unfinished\n");
return -1;
}
if (write == I2C_WRITE_BIT && (csr & I2C_SR_RXAK)) {
debug("i2c_wait: No RXACK\n");
return -1;
}
return 0;
} while ((get_ticks() - timeval) < timeout);
debug("i2c_wait: timed out\n");
return -1;
}
static __inline__ int
i2c_write_addr(struct i2c_adapter *adap, u8 dev, u8 dir, int rsta)
{
struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX
| (rsta ? I2C_CR_RSTA : 0),
&device->cr);
writeb((dev << 1) | dir, &device->dr);
if (i2c_wait(adap, I2C_WRITE_BIT) < 0)
return 0;
return 1;
}
static __inline__ int
__i2c_write(struct i2c_adapter *adap, u8 *data, int length)
{
struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i;
for (i = 0; i < length; i++) {
writeb(data[i], &dev->dr);
if (i2c_wait(adap, I2C_WRITE_BIT) < 0)
break;
}
return i;
}
static __inline__ int
__i2c_read(struct i2c_adapter *adap, u8 *data, int length)
{
struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i;
writeb(I2C_CR_MEN | I2C_CR_MSTA | ((length == 1) ? I2C_CR_TXAK : 0),
&dev->cr);
/* dummy read */
readb(&dev->dr);
for (i = 0; i < length; i++) {
if (i2c_wait(adap, I2C_READ_BIT) < 0)
break;
/* Generate ack on last next to last byte */
if (i == length - 2)
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK,
&dev->cr);
/* Do not generate stop on last byte */
if (i == length - 1)
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX,
&dev->cr);
data[i] = readb(&dev->dr);
}
return i;
}
static int
fsl_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, int alen, u8 *data,
int length)
{
struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i = -1; /* signal error */
u8 *a = (u8*)&addr;
int len = alen * -1;
if (i2c_wait4bus(adap) < 0)
return -1;
/* To handle the need of I2C devices that require to write few bytes
* (more than 4 bytes of address as in the case of else part)
* of data before reading, Negative equivalent of length(bytes to write)
* is passed, but used the +ve part of len for writing data
*/
if (alen < 0) {
/* Generate a START and send the Address and
* the Tx Bytes to the slave.
* "START: Address: Write bytes data[len]"
* IF part supports writing any number of bytes in contrast
* to the else part, which supports writing address offset
* of upto 4 bytes only.
* bytes that need to be written are passed in
* "data", which will eventually keep the data READ,
* after writing the len bytes out of it
*/
if (i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0)
i = __i2c_write(adap, data, len);
if (i != len)
return -1;
if (length && i2c_write_addr(adap, dev, I2C_READ_BIT, 1) != 0)
i = __i2c_read(adap, data, length);
} else {
if ((!length || alen > 0) &&
i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 &&
__i2c_write(adap, &a[4 - alen], alen) == alen)
i = 0; /* No error so far */
if (length &&
i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
i = __i2c_read(adap, data, length);
}
writeb(I2C_CR_MEN, &device->cr);
if (i2c_wait4bus(adap)) /* Wait until STOP */
debug("i2c_read: wait4bus timed out\n");
if (i == length)
return 0;
return -1;
}
static int
fsl_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, int alen,
u8 *data, int length)
{
struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
int i = -1; /* signal error */
u8 *a = (u8*)&addr;
if (i2c_wait4bus(adap) < 0)
return -1;
if (i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 &&
__i2c_write(adap, &a[4 - alen], alen) == alen) {
i = __i2c_write(adap, data, length);
}
writeb(I2C_CR_MEN, &device->cr);
if (i2c_wait4bus(adap)) /* Wait until STOP */
debug("i2c_write: wait4bus timed out\n");
if (i == length)
return 0;
return -1;
}
static int
fsl_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
/* For unknow reason the controller will ACK when
* probing for a slave with the same address, so skip
* it.
*/
if (chip == (readb(&dev->adr) >> 1))
return -1;
return fsl_i2c_read(adap, chip, 0, 0, NULL, 0);
}
static unsigned int fsl_i2c_set_bus_speed(struct i2c_adapter *adap,
unsigned int speed)
{
struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr];
writeb(0, &dev->cr); /* stop controller */
set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed);
writeb(I2C_CR_MEN, &dev->cr); /* start controller */
return 0;
}
/*
* Register fsl i2c adapters
*/
U_BOOT_I2C_ADAP_COMPLETE(fsl_0, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read,
fsl_i2c_write, fsl_i2c_set_bus_speed,
CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE,
0)
#ifdef CONFIG_SYS_FSL_I2C2_OFFSET
U_BOOT_I2C_ADAP_COMPLETE(fsl_1, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read,
fsl_i2c_write, fsl_i2c_set_bus_speed,
CONFIG_SYS_FSL_I2C2_SPEED, CONFIG_SYS_FSL_I2C2_SLAVE,
1)
#endif