u-boot/arch/arm/mach-zynqmp/spl.c
Andrew F. Davis 6536ca4d66 spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-26 08:13:54 -05:00

134 lines
2.8 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 - 2016 Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
#include <common.h>
#include <debug_uart.h>
#include <spl.h>
#include <asm/io.h>
#include <asm/spl.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sys_proto.h>
void board_init_f(ulong dummy)
{
board_early_init_f();
board_early_init_r();
#ifdef CONFIG_DEBUG_UART
/* Uart debug for sure */
debug_uart_init();
puts("Debug uart enabled\n"); /* or printch() */
#endif
/* Delay is required for clocks to be propagated */
udelay(1000000);
/* Clear the BSS */
memset(__bss_start, 0, __bss_end - __bss_start);
/* No need to call timer init - it is empty for ZynqMP */
board_init_r(NULL, 0);
}
static void ps_mode_reset(ulong mode)
{
writel(mode << ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_EN_SHIFT,
&crlapb_base->boot_pin_ctrl);
udelay(5);
writel(mode << ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_VAL_SHIFT |
mode << ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_EN_SHIFT,
&crlapb_base->boot_pin_ctrl);
}
/*
* Set default PS_MODE1 which is used for USB ULPI phy reset
* Also other resets can be connected to this certain pin
*/
#ifndef MODE_RESET
# define MODE_RESET PS_MODE1
#endif
#ifdef CONFIG_SPL_BOARD_INIT
void spl_board_init(void)
{
preloader_console_init();
ps_mode_reset(MODE_RESET);
board_init();
}
#endif
u32 spl_boot_device(void)
{
u32 reg = 0;
u8 bootmode;
#if defined(CONFIG_SPL_ZYNQMP_ALT_BOOTMODE_ENABLED)
/* Change default boot mode at run-time */
writel(CONFIG_SPL_ZYNQMP_ALT_BOOTMODE << BOOT_MODE_ALT_SHIFT,
&crlapb_base->boot_mode);
#endif
reg = readl(&crlapb_base->boot_mode);
if (reg >> BOOT_MODE_ALT_SHIFT)
reg >>= BOOT_MODE_ALT_SHIFT;
bootmode = reg & BOOT_MODES_MASK;
switch (bootmode) {
case JTAG_MODE:
return BOOT_DEVICE_RAM;
#ifdef CONFIG_SPL_MMC_SUPPORT
case SD_MODE1:
case SD1_LSHFT_MODE: /* not working on silicon v1 */
/* if both controllers enabled, then these two are the second controller */
#if defined(CONFIG_ZYNQ_SDHCI0) && defined(CONFIG_ZYNQ_SDHCI1)
return BOOT_DEVICE_MMC2;
/* else, fall through, the one SDHCI controller that is enabled is number 1 */
#endif
case SD_MODE:
case EMMC_MODE:
return BOOT_DEVICE_MMC1;
#endif
#ifdef CONFIG_SPL_DFU
case USB_MODE:
return BOOT_DEVICE_DFU;
#endif
#ifdef CONFIG_SPL_SATA_SUPPORT
case SW_SATA_MODE:
return BOOT_DEVICE_SATA;
#endif
#ifdef CONFIG_SPL_SPI_SUPPORT
case QSPI_MODE_24BIT:
case QSPI_MODE_32BIT:
return BOOT_DEVICE_SPI;
#endif
default:
printf("Invalid Boot Mode:0x%x\n", bootmode);
break;
}
return 0;
}
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
handoff_setup();
return 0;
}
#endif
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif