mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-12 06:12:58 +00:00
b1c2a7ae32
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high" This is necessary on Kirkwood so that the FDT does not get relocated above the memory limit that the kernel cannot access (that is the memory part reserved for the switch). This was tested on NUSA1, where it is necessary, and on ETER1, where it doesn't seem to hurt. We want the scripts to also work with older versions of u-boot, where: a) set_fdthigh is not defined (will be default env for newer u-boots) b) the fdt will not be available For this reason, we use "set_fdthigh" to tell whether we are running a newer (FDT-aware) u-boot or not. So if "set_fdthigh" runs successfully or arch != arm we try loading the fdt; otherwise we proceed normally. Notice how, contrary to release mode, set_fdthigh will _not_ be part of subbootcmds for develop and ramfs, but will be executed as part of "tftpfdt". Since this is only needed for kirkwood cards, and it prevents the kernel from booting on QorIQ (though it seemed to work on ETER1), we change its definition in the default env for powerpc so that the value is only set on ARM. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
83 lines
2.7 KiB
C
83 lines
2.7 KiB
C
/*
|
|
* (C) Copyright 2011
|
|
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_KEYMILE_POWERPC_H
|
|
#define __CONFIG_KEYMILE_POWERPC_H
|
|
|
|
/* Do boardspecific init for all boards */
|
|
#define CONFIG_BOARD_EARLY_INIT_R
|
|
#define CONFIG_LAST_STAGE_INIT
|
|
|
|
#define CONFIG_BOOTCOUNT_LIMIT
|
|
|
|
#define CONFIG_CMD_DTT
|
|
#define CONFIG_JFFS2_CMDLINE
|
|
|
|
/* standard km ethernet_present for piggy */
|
|
#define CONFIG_KM_COMMON_ETH_INIT
|
|
|
|
/* EEprom support 24C08, 24C16, 24C64 */
|
|
#define CONFIG_SYS_I2C_MULTI_EEPROMS
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 8 Byte write page */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
|
|
#define CONFIG_ENV_SIZE 0x04000 /* Size of Environment */
|
|
#define CONFIG_FLASH_CFI_MTD
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
|
|
|
|
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
/* Reserve 4 MB for malloc */
|
|
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
|
|
|
|
/******************************************************************************
|
|
* (PRAM usage)
|
|
* ... -------------------------------------------------------
|
|
* ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
|
|
* ... |<------------------- pram -------------------------->|
|
|
* ... -------------------------------------------------------
|
|
* @END_OF_RAM:
|
|
* @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
|
|
* @CONFIG_KM_PHRAM: address for /var
|
|
* @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
|
|
* @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
|
|
*/
|
|
|
|
/* size of rootfs in RAM */
|
|
#define CONFIG_KM_ROOTFSSIZE 0x0
|
|
/* pseudo-non volatile RAM [hex] */
|
|
#define CONFIG_KM_PNVRAM 0x80000
|
|
/* physical RAM MTD size [hex] */
|
|
#define CONFIG_KM_PHRAM 0x100000
|
|
/* resereved pram area at the end of memroy [hex] */
|
|
#define CONFIG_KM_RESERVED_PRAM 0x0
|
|
/* enable protected RAM */
|
|
#define CONFIG_PRAM 0
|
|
|
|
#define CONFIG_KM_CRAMFS_ADDR 0x800000
|
|
#define CONFIG_KM_KERNEL_ADDR 0x400000 /* 3968Kbytes */
|
|
#define CONFIG_KM_FDT_ADDR 0x7E0000 /* 128Kbytes */
|
|
|
|
/* architecture specific default bootargs */
|
|
#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
|
|
|
|
#define CONFIG_KM_DEF_ENV_CPU \
|
|
"u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \
|
|
"update=" \
|
|
"protect off " __stringify(BOOTFLASH_START) " +${filesize} && "\
|
|
"erase " __stringify(BOOTFLASH_START) " +${filesize} && "\
|
|
"cp.b ${load_addr_r} " __stringify(BOOTFLASH_START) \
|
|
" ${filesize} && " \
|
|
"protect on " __stringify(BOOTFLASH_START) " +${filesize}\0"\
|
|
"set_fdthigh=true\0" \
|
|
""
|
|
|
|
#endif /* __CONFIG_KEYMILE_POWERPC_H */
|