u-boot/board/BuR/tseries/board.c
Hannes Petermaier ef1bd8f416 board/BuR/tseries: only run gpmc_init(...) in NAND-build
if we have no NAND-Chip, we don't need the gpmc-controller and therefore
is no need to init it.

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-06-06 17:46:15 -04:00

149 lines
3.8 KiB
C

/*
* board.c
*
* Board functions for B&R LEIT Board
*
* Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
* Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
*
* SPDX-License-Identifier: GPL-2.0+
*
*/
#include <common.h>
#include <errno.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mem.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include <i2c.h>
#include <power/tps65217.h>
#include "../common/bur_common.h"
DECLARE_GLOBAL_DATA_PTR;
/* --------------------------------------------------------------------------*/
/* -- defines for GPIO -- */
#define ETHLED_ORANGE (96+16) /* GPIO3_16 */
#define REPSWITCH (0+20) /* GPIO0_20 */
#if defined(CONFIG_SPL_BUILD)
/* TODO: check ram-timing ! */
static const struct ddr_data ddr3_data = {
.datardsratio0 = MT41K256M16HA125E_RD_DQS,
.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
};
static const struct cmd_control ddr3_cmd_ctrl_data = {
.cmd0csratio = MT41K256M16HA125E_RATIO,
.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd1csratio = MT41K256M16HA125E_RATIO,
.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd2csratio = MT41K256M16HA125E_RATIO,
.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};
static struct emif_regs ddr3_emif_reg_data = {
.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
.zq_config = MT41K256M16HA125E_ZQ_CFG,
.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
};
static const struct ctrl_ioregs ddr3_ioregs = {
.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
};
#ifdef CONFIG_SPL_OS_BOOT
/*
* called from spl_nand.c
* return 0 for loading linux, return 1 for loading u-boot
*/
int spl_start_uboot(void)
{
if (0 == gpio_get_value(REPSWITCH)) {
blink(5, 125, ETHLED_ORANGE);
mdelay(1000);
printf("SPL: entering u-boot instead kernel image.\n");
return 1;
}
return 0;
}
#endif /* CONFIG_SPL_OS_BOOT */
#define OSC (V_OSCK/1000000)
static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
void am33xx_spl_board_init(void)
{
pmicsetup(1000);
}
const struct dpll_params *get_dpll_ddr_params(void)
{
return &dpll_ddr3;
}
void sdram_init(void)
{
config_ddr(400, &ddr3_ioregs,
&ddr3_data,
&ddr3_cmd_ctrl_data,
&ddr3_emif_reg_data, 0);
}
#endif /* CONFIG_SPL_BUILD */
/* Basic board specific setup. Pinmux has been handled already. */
int board_init(void)
{
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_NAND
gpmc_init();
#endif
return 0;
}
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
gpio_direction_output(ETHLED_ORANGE, 0);
if (0 == gpio_get_value(REPSWITCH)) {
printf("\n\n\n"
"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n"
"!!!!!!! recovery switch activated !!!!!!!\n"
"!!!!!!! running usbupdate !!!!!!!\n"
"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n\n\n");
setenv("bootcmd", "sleep 2; run netupdate;");
}
printf("turning on display power+backlight ... ");
tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL1,
0x09, TPS65217_MASK_ALL_BITS); /* 200 Hz, ON */
tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL2,
0x62, TPS65217_MASK_ALL_BITS); /* 100% */
printf("ok.\n");
return 0;
}
#endif /* CONFIG_BOARD_LATE_INIT */