mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-13 23:02:59 +00:00
656d8da9d2
Commit ad7061ed74
("doc: Move device tree bindings documentation to
doc/device-tree-bindings") moved all device tree binding documentation
to doc/device-tree-bindings directory.
The current U-Boot project still have two documentation directories:
- doc/
- Documentation/
Move all documentation and sphinx files to doc directory so all content
can be in a common place.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
314 lines
14 KiB
Text
314 lines
14 KiB
Text
MPC83xx RAM controller
|
|
|
|
This driver supplies support for the embedded RAM controller on MCP83xx-series
|
|
SoCs.
|
|
|
|
For static configuration mode, each controller node should have child nodes
|
|
describing the actual RAM modules installed.
|
|
|
|
Controller node
|
|
===============
|
|
|
|
Required properties:
|
|
- compatible: Must be "fsl,mpc83xx-mem-controller"
|
|
- reg: The address of the RAM controller's register space
|
|
- #address-cells: Must be 2
|
|
- #size-cells: Must be 1
|
|
- driver_software_override: DDR driver software override is enabled (1) or
|
|
disabled (0)
|
|
- p_impedance_override: DDR driver software p-impedance override; possible
|
|
values:
|
|
* DSO_P_IMPEDANCE_HIGHEST_Z
|
|
* DSO_P_IMPEDANCE_MUCH_HIGHER_Z
|
|
* DSO_P_IMPEDANCE_HIGHER_Z
|
|
* DSO_P_IMPEDANCE_NOMINAL
|
|
* DSO_P_IMPEDANCE_LOWER_Z
|
|
- n_impedance_override: DDR driver software n-impedance override; possible
|
|
values:
|
|
* DSO_N_IMPEDANCE_HIGHEST_Z
|
|
* DSO_N_IMPEDANCE_MUCH_HIGHER_Z
|
|
* DSO_N_IMPEDANCE_HIGHER_Z
|
|
* DSO_N_IMPEDANCE_NOMINAL
|
|
* DSO_N_IMPEDANCE_LOWER_Z
|
|
- odt_termination_value: ODT termination value for I/Os; possible values:
|
|
* ODT_TERMINATION_75_OHM
|
|
* ODT_TERMINATION_150_OHM
|
|
- ddr_type: Selects voltage level for DDR pads; possible
|
|
values:
|
|
* DDR_TYPE_DDR2_1_8_VOLT
|
|
* DDR_TYPE_DDR1_2_5_VOLT
|
|
- mvref_sel: Determine where MVREF_SEL signal is generated;
|
|
possible values:
|
|
* MVREF_SEL_EXTERNAL
|
|
* MVREF_SEL_INTERNAL_GVDD
|
|
- m_odr: Disable memory transaction reordering; possible
|
|
values:
|
|
* M_ODR_ENABLE
|
|
* M_ODR_DISABLE
|
|
- clock_adjust: Clock adjust; possible values:
|
|
* CLOCK_ADJUST_025
|
|
* CLOCK_ADJUST_05
|
|
* CLOCK_ADJUST_075
|
|
* CLOCK_ADJUST_1
|
|
- ext_refresh_rec: Extended refresh recovery time; possible values:
|
|
0, 16, 32, 48, 64, 80, 96, 112
|
|
- read_to_write: Read-to-write turnaround; possible values:
|
|
0, 1, 2, 3
|
|
- write_to_read: Write-to-read turnaround; possible values:
|
|
0, 1, 2, 3
|
|
- read_to_read: Read-to-read turnaround; possible values:
|
|
0, 1, 2, 3
|
|
- write_to_write: Write-to-write turnaround; possible values:
|
|
0, 1, 2, 3
|
|
- active_powerdown_exit: Active powerdown exit timing; possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- precharge_powerdown_exit: Precharge powerdown exit timing; possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- odt_powerdown_exit: ODT powerdown exit timing; possible values:
|
|
0, 1, 2, 3, 4, 5, 6, 7, 8,
|
|
9, 10, 11, 12, 13, 14, 15
|
|
- mode_reg_set_cycle: Mode register set cycle time; possible values:
|
|
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15
|
|
- precharge_to_activate: Precharge-to-acitvate interval; possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- activate_to_precharge: Activate to precharge interval; possible values:
|
|
4, 5, 6, 7, 8, 9, 10, 11, 12,
|
|
13, 14, 15, 16, 17, 18, 19
|
|
- activate_to_readwrite: Activate to read/write interval for SDRAM;
|
|
possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- mcas_latency: MCAS latency from READ command; possible values:
|
|
* CASLAT_20
|
|
* CASLAT_25
|
|
* CASLAT_30
|
|
* CASLAT_35
|
|
* CASLAT_40
|
|
* CASLAT_45
|
|
* CASLAT_50
|
|
* CASLAT_55
|
|
* CASLAT_60
|
|
* CASLAT_65
|
|
* CASLAT_70
|
|
* CASLAT_75
|
|
* CASLAT_80
|
|
- refresh_recovery: Refresh recovery time; possible values:
|
|
8, 9, 10, 11, 12, 13, 14, 15,
|
|
16, 17, 18, 19, 20, 21, 22, 23
|
|
- last_data_to_precharge: Last data to precharge minimum interval; possible
|
|
values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- activate_to_activate: Activate-to-activate interval; possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- last_write_data_to_read: Last write data pair to read command issue
|
|
interval; possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- additive_latency: Additive latency; possible values:
|
|
0, 1, 2, 3, 4, 5
|
|
- mcas_to_preamble_override: MCAS-to-preamble-override; possible values:
|
|
* READ_LAT
|
|
* READ_LAT_PLUS_1_4
|
|
* READ_LAT_PLUS_1_2
|
|
* READ_LAT_PLUS_3_4
|
|
* READ_LAT_PLUS_1
|
|
* READ_LAT_PLUS_5_4
|
|
* READ_LAT_PLUS_3_2
|
|
* READ_LAT_PLUS_7_4
|
|
* READ_LAT_PLUS_2
|
|
* READ_LAT_PLUS_9_4
|
|
* READ_LAT_PLUS_5_2
|
|
* READ_LAT_PLUS_11_4
|
|
* READ_LAT_PLUS_3
|
|
* READ_LAT_PLUS_13_4
|
|
* READ_LAT_PLUS_7_2
|
|
* READ_LAT_PLUS_15_4
|
|
* READ_LAT_PLUS_4
|
|
* READ_LAT_PLUS_17_4
|
|
* READ_LAT_PLUS_9_2
|
|
* READ_LAT_PLUS_19_4
|
|
- write_latency: Write latency; possible values:
|
|
1, 2, 3, 4, 5, 6, 7
|
|
- read_to_precharge: Read to precharge; possible values:
|
|
1, 2, 3, 4
|
|
- write_cmd_to_write_data: Write command to write data strobe timing
|
|
adjustment; possible values:
|
|
* CLOCK_DELAY_0
|
|
* CLOCK_DELAY_1_4
|
|
* CLOCK_DELAY_1_2
|
|
* CLOCK_DELAY_3_4
|
|
* CLOCK_DELAY_1
|
|
* CLOCK_DELAY_5_4
|
|
* CLOCK_DELAY_3_2
|
|
- minimum_cke_pulse_width: Minimum CKE pulse width; possible values:
|
|
1, 2, 3, 4
|
|
- four_activates_window: Window for four activates; possible values:
|
|
1, 2, 3, 4 8, 9, 10, 11, 12,
|
|
13, 14, 15, 16, 17, 18, 19
|
|
- self_refresh: Self refresh (during sleep); possible values:
|
|
* SREN_DISABLE
|
|
* SREN_ENABLE
|
|
- ecc: Support for ECC; possible values:
|
|
* ECC_DISABLE
|
|
* ECC_ENABLE
|
|
- registered_dram: Support for registered DRAM; possible values:
|
|
* RD_DISABLE
|
|
* RD_ENABLE
|
|
- sdram_type: Type of SDRAM device to be used; possible values:
|
|
* TYPE_DDR1
|
|
* TYPE_DDR2
|
|
- dynamic_power_management: Dynamic power management mode; possible values:
|
|
* DYN_PWR_DISABLE
|
|
* DYN_PWR_ENABLE
|
|
- databus_width: DRAM data bus width; possible values
|
|
* DATA_BUS_WIDTH_16
|
|
* DATA_BUS_WIDTH_32
|
|
- nc_auto_precharge: Non-concurrent auto-precharge; possible values:
|
|
* NCAP_DISABLE
|
|
* NCAP_ENABLE
|
|
- timing_2t: 2T timing; possible values:
|
|
* TIMING_1T
|
|
* TIMING_2T
|
|
- bank_interleaving_ctrl: Bank (chip select) interleaving control; possible
|
|
values:
|
|
* INTERLEAVE_NONE
|
|
* INTERLEAVE_1_AND_2
|
|
- precharge_bit_8: Precharge bin 8; possible values
|
|
* PRECHARGE_MA_10
|
|
* PRECHARGE_MA_8
|
|
- half_strength: Global half-strength override; possible values:
|
|
* STRENGTH_FULL
|
|
* STRENGTH_HALF
|
|
- bypass_initialization: Bypass initialization; possible values:
|
|
* INITIALIZATION_DONT_BYPASS
|
|
* INITIALIZATION_BYPASS
|
|
- force_self_refresh: Force self refresh; possible values:
|
|
* MODE_NORMAL
|
|
* MODE_REFRESH
|
|
- dll_reset: DLL reset; possible values:
|
|
* DLL_RESET_ENABLE
|
|
* DLL_RESET_DISABLE
|
|
- dqs_config: DQS configuration; possible values:
|
|
* DQS_TRUE
|
|
- odt_config: ODT configuration; possible values:
|
|
* ODT_ASSERT_NEVER
|
|
* ODT_ASSERT_WRITES
|
|
* ODT_ASSERT_READS
|
|
* ODT_ASSERT_ALWAYS
|
|
- posted_refreshes: Number of posted refreshes
|
|
1, 2, 3, 4, 5, 6, 7, 8
|
|
- sdmode: Initial value loaded into the DDR SDRAM mode
|
|
register
|
|
- esdmode: Initial value loaded into the DDR SDRAM extended
|
|
mode register
|
|
- esdmode2: Initial value loaded into the DDR SDRAM extended
|
|
mode 2 register
|
|
- esdmode3: Initial value loaded into the DDR SDRAM extended
|
|
mode 3 register
|
|
- refresh_interval: Refresh interval; possible values:
|
|
0 - 65535
|
|
- precharge_interval: Precharge interval; possible values:
|
|
0 - 16383
|
|
|
|
RAM module node:
|
|
================
|
|
|
|
Required properties:
|
|
- reg: A triple <cs addr size>, which consists of:
|
|
* cs - the chipselect used to drive this RAM module
|
|
* addr - the address where this RAM module's memory is map
|
|
to in the global memory space
|
|
* size - the size of the RAM module's memory in bytes
|
|
- auto_precharge: Chip select auto-precharge; possible values:
|
|
* AUTO_PRECHARGE_ENABLE
|
|
* AUTO_PRECHARGE_DISABLE
|
|
- odt_rd_cfg: ODT for reads configuration; possible values:
|
|
* ODT_RD_NEVER
|
|
* ODT_RD_ONLY_CURRENT
|
|
* ODT_RD_ONLY_OTHER_CS
|
|
* ODT_RD_ONLY_OTHER_DIMM
|
|
* ODT_RD_ALL
|
|
- odt_wr_cfg: ODT for writes configuration; possible values:
|
|
* ODT_WR_NEVER
|
|
* ODT_WR_ONLY_CURRENT
|
|
* ODT_WR_ONLY_OTHER_CS
|
|
* ODT_WR_ONLY_OTHER_DIMM
|
|
* ODT_WR_ALL
|
|
- bank_bits: Number of bank bits for SDRAM on chip select; possible
|
|
values:
|
|
2, 3
|
|
- row_bits: Number of row bits for SDRAM on chip select; possible values:
|
|
12, 13, 14
|
|
- col_bits: Number of column bits for SDRAM on chip select; possible
|
|
values:
|
|
8, 9, 10, 11
|
|
|
|
Example:
|
|
|
|
memory@2000 {
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
compatible = "fsl,mpc83xx-mem-controller";
|
|
reg = <0x2000 0x1000>;
|
|
device_type = "memory";
|
|
u-boot,dm-pre-reloc;
|
|
|
|
driver_software_override = <DSO_ENABLE>;
|
|
p_impedance_override = <DSO_P_IMPEDANCE_NOMINAL>;
|
|
n_impedance_override = <DSO_N_IMPEDANCE_NOMINAL>;
|
|
odt_termination_value = <ODT_TERMINATION_150_OHM>;
|
|
ddr_type = <DDR_TYPE_DDR2_1_8_VOLT>;
|
|
|
|
clock_adjust = <CLOCK_ADJUST_05>;
|
|
|
|
read_to_write = <0>;
|
|
write_to_read = <0>;
|
|
read_to_read = <0>;
|
|
write_to_write = <0>;
|
|
active_powerdown_exit = <2>;
|
|
precharge_powerdown_exit = <6>;
|
|
odt_powerdown_exit = <8>;
|
|
mode_reg_set_cycle = <2>;
|
|
|
|
precharge_to_activate = <2>;
|
|
activate_to_precharge = <6>;
|
|
activate_to_readwrite = <2>;
|
|
mcas_latency = <CASLAT_40>;
|
|
refresh_recovery = <17>;
|
|
last_data_to_precharge = <2>;
|
|
activate_to_activate = <2>;
|
|
last_write_data_to_read = <2>;
|
|
|
|
additive_latency = <0>;
|
|
mcas_to_preamble_override = <READ_LAT_PLUS_1_2>;
|
|
write_latency = <3>;
|
|
read_to_precharge = <2>;
|
|
write_cmd_to_write_data = <CLOCK_DELAY_1_2>;
|
|
minimum_cke_pulse_width = <3>;
|
|
four_activates_window = <5>;
|
|
|
|
self_refresh = <SREN_ENABLE>;
|
|
sdram_type = <TYPE_DDR2>;
|
|
databus_width = <DATA_BUS_WIDTH_32>;
|
|
|
|
force_self_refresh = <MODE_NORMAL>;
|
|
dll_reset = <DLL_RESET_ENABLE>;
|
|
dqs_config = <DQS_TRUE>;
|
|
odt_config = <ODT_ASSERT_READS>;
|
|
posted_refreshes = <1>;
|
|
|
|
refresh_interval = <2084>;
|
|
precharge_interval = <256>;
|
|
|
|
sdmode = <0x0242>;
|
|
esdmode = <0x0440>;
|
|
|
|
ram@0 {
|
|
reg = <0x0 0x0 0x8000000>;
|
|
compatible = "nanya,nt5tu64m16hg";
|
|
|
|
odt_rd_cfg = <ODT_RD_NEVER>;
|
|
odt_wr_cfg = <ODT_WR_ONLY_CURRENT>;
|
|
bank_bits = <3>;
|
|
row_bits = <13>;
|
|
col_bits = <10>;
|
|
};
|
|
};
|