mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 16:39:35 +00:00
a0942a6d3e
On pit and pi the TPS65090 regulator is connected only to the EC and we must use a tunnel to get to it. The existing U-Boot support relies on a special driver. Add a tunnel definition so that the new device-model TPS65090 driver can be used unmodified. Signed-off-by: Simon Glass <sjg@chromium.org>
233 lines
4.8 KiB
Text
233 lines
4.8 KiB
Text
/*
|
|
* SAMSUNG/GOOGLE Peach-Pit board device tree source
|
|
*
|
|
* Copyright (c) 2013 Samsung Electronics Co., Ltd.
|
|
* http://www.samsung.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "exynos54xx.dtsi"
|
|
|
|
/ {
|
|
model = "Samsung/Google Peach Pi board based on Exynos5800";
|
|
|
|
compatible = "google,pit-rev#", "google,pit",
|
|
"google,peach", "samsung,exynos5800", "samsung,exynos5";
|
|
|
|
config {
|
|
google,bad-wake-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
|
|
hwid = "PIT TEST A-A 7848";
|
|
lazy-init = <1>;
|
|
};
|
|
|
|
aliases {
|
|
serial0 = "/serial@12C30000";
|
|
console = "/serial@12C30000";
|
|
pmic = "/i2c@12CA0000";
|
|
i2c104 = &i2c_tunnel;
|
|
};
|
|
|
|
dmc {
|
|
mem-manuf = "samsung";
|
|
mem-type = "ddr3";
|
|
clock-frequency = <800000000>;
|
|
arm-frequency = <900000000>;
|
|
};
|
|
|
|
tmu@10060000 {
|
|
samsung,min-temp = <25>;
|
|
samsung,max-temp = <125>;
|
|
samsung,start-warning = <95>;
|
|
samsung,start-tripping = <105>;
|
|
samsung,hw-tripping = <110>;
|
|
samsung,efuse-min-value = <40>;
|
|
samsung,efuse-value = <55>;
|
|
samsung,efuse-max-value = <100>;
|
|
samsung,slope = <274761730>;
|
|
samsung,dc-value = <25>;
|
|
};
|
|
|
|
/* MAX77802 is on i2c bus 4 */
|
|
i2c@12CA0000 {
|
|
clock-frequency = <400000>;
|
|
power-regulator@9 {
|
|
compatible = "maxim,max77802-pmic";
|
|
reg = <0x9>;
|
|
};
|
|
};
|
|
|
|
i2c@12CD0000 { /* i2c7 */
|
|
clock-frequency = <100000>;
|
|
soundcodec@20 {
|
|
reg = <0x20>;
|
|
compatible = "maxim,max98090-codec";
|
|
};
|
|
};
|
|
|
|
sound@3830000 {
|
|
samsung,codec-type = "max98090";
|
|
};
|
|
|
|
i2c@12E10000 { /* i2c9 */
|
|
clock-frequency = <400000>;
|
|
tpm@20 {
|
|
compatible = "infineon,slb9645tt";
|
|
reg = <0x20>;
|
|
};
|
|
};
|
|
|
|
spi@12d30000 { /* spi1 */
|
|
spi-max-frequency = <50000000>;
|
|
firmware_storage_spi: flash@0 {
|
|
reg = <0>;
|
|
|
|
/*
|
|
* A region for the kernel to store a panic event
|
|
* which the firmware will add to the log.
|
|
*/
|
|
elog-panic-event-offset = <0x01e00000 0x100000>;
|
|
|
|
elog-shrink-size = <0x400>;
|
|
elog-full-threshold = <0xc00>;
|
|
};
|
|
};
|
|
|
|
xhci@12000000 {
|
|
samsung,vbus-gpio = <&gph0 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
xhci@12400000 {
|
|
samsung,vbus-gpio = <&gph0 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
fimd@14400000 {
|
|
samsung,vl-freq = <60>;
|
|
samsung,vl-col = <1920>;
|
|
samsung,vl-row = <1080>;
|
|
samsung,vl-width = <1920>;
|
|
samsung,vl-height = <1080>;
|
|
|
|
samsung,vl-clkp;
|
|
samsung,vl-dp;
|
|
samsung,vl-bpix = <4>;
|
|
|
|
samsung,vl-hspw = <80>;
|
|
samsung,vl-hbpd = <172>;
|
|
samsung,vl-hfpd = <60>;
|
|
samsung,vl-vspw = <10>;
|
|
samsung,vl-vbpd = <25>;
|
|
samsung,vl-vfpd = <10>;
|
|
samsung,vl-cmd-allow-len = <0xf>;
|
|
|
|
samsung,power-on-delay = <30000>;
|
|
samsung,winid = <3>;
|
|
samsung,interface-mode = <1>;
|
|
samsung,dp-enabled = <1>;
|
|
samsung,dual-lcd-enabled = <0>;
|
|
|
|
samsung,bl-en-gpio = <&gpx2 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
&spi_2 {
|
|
spi-max-frequency = <3125000>;
|
|
spi-deactivate-delay = <200>;
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
samsung,spi-src-clk = <0>;
|
|
cs-gpios = <&gpb1 2 0>;
|
|
|
|
cros_ec: cros-ec@0 {
|
|
compatible = "google,cros-ec-spi";
|
|
interrupt-parent = <&gpx1>;
|
|
interrupts = <5 0>;
|
|
reg = <0>;
|
|
spi-half-duplex;
|
|
spi-max-timeout-ms = <1100>;
|
|
ec-interrupt = <&gpx1 5 GPIO_ACTIVE_LOW>;
|
|
|
|
/*
|
|
* This describes the flash memory within the EC. Note
|
|
* that the STM32L flash erases to 0, not 0xff.
|
|
*/
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
flash@8000000 {
|
|
reg = <0x08000000 0x20000>;
|
|
erase-value = <0>;
|
|
};
|
|
|
|
controller-data {
|
|
samsung,spi-feedback-delay = <1>;
|
|
};
|
|
|
|
i2c_tunnel: i2c-tunnel {
|
|
compatible = "google,cros-ec-i2c-tunnel";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
google,remote-bus = <0>;
|
|
|
|
battery: sbs-battery@b {
|
|
compatible = "sbs,sbs-battery";
|
|
reg = <0xb>;
|
|
sbs,poll-retry-count = <1>;
|
|
sbs,i2c-retry-count = <2>;
|
|
};
|
|
|
|
power-regulator@48 {
|
|
compatible = "ti,tps65090";
|
|
reg = <0x48>;
|
|
|
|
regulators {
|
|
tps65090_dcdc1: dcdc1 {
|
|
ti,enable-ext-control;
|
|
};
|
|
tps65090_dcdc2: dcdc2 {
|
|
ti,enable-ext-control;
|
|
};
|
|
tps65090_dcdc3: dcdc3 {
|
|
ti,enable-ext-control;
|
|
};
|
|
tps65090_fet1: fet1 {
|
|
regulator-name = "vcd_led";
|
|
};
|
|
tps65090_fet2: fet2 {
|
|
regulator-name = "video_mid";
|
|
regulator-always-on;
|
|
};
|
|
tps65090_fet3: fet3 {
|
|
regulator-name = "wwan_r";
|
|
regulator-always-on;
|
|
};
|
|
tps65090_fet4: fet4 {
|
|
regulator-name = "sdcard";
|
|
regulator-always-on;
|
|
};
|
|
tps65090_fet5: fet5 {
|
|
regulator-name = "camout";
|
|
regulator-always-on;
|
|
};
|
|
tps65090_fet6: fet6 {
|
|
regulator-name = "lcd_vdd";
|
|
};
|
|
tps65090_fet7: fet7 {
|
|
regulator-name = "video_mid_1a";
|
|
regulator-always-on;
|
|
};
|
|
tps65090_ldo1: ldo1 {
|
|
};
|
|
tps65090_ldo2: ldo2 {
|
|
};
|
|
};
|
|
|
|
charger {
|
|
compatible = "ti,tps65090-charger";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
#include "cros-ec-keyboard.dtsi"
|