u-boot/include/configs/p3450-0000.h
Tom Rini f76750d111 Convert CONFIG_CONS_INDEX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX
   CONFIG_DEBUG_UART_CLOCK
   CONFIG_FSL_TZPC_BP147
   CONFIG_GENERIC_ATMEL_MCI
   CONFIG_IDENT_STRING
   CONFIG_LIBATA
   CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
   CONFIG_LPC32XX_GPIO
   CONFIG_MP
   CONFIG_MPC8XXX_GPIO
   CONFIG_MTD_PARTITIONS
   CONFIG_MVGBE
   CONFIG_MXC_GPIO
   CONFIG_NR_DRAM_BANKS
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_PREBOOT
   CONFIG_ROCKCHIP_SERIAL
   CONFIG_RTC_ENABLE_32KHZ_OUTPUT
   CONFIG_RTC_MV
   CONFIG_SCSI_AHCI
   CONFIG_SF_DEFAULT_BUS
   CONFIG_SF_DEFAULT_CS
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SOFT_SPI
   CONFIG_SPI_FLASH_EON
   CONFIG_SPI_FLASH_MACRONIX
   CONFIG_SPI_FLASH_MTD
   CONFIG_SPI_FLASH_SPANSION
   CONFIG_SPI_FLASH_SST
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_SYS_ARCH_TIMER
   CONFIG_SYS_BOARD
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
   CONFIG_SYS_DCACHE_OFF
   CONFIG_SYS_FDT_SAVE_ADDRESS
   CONFIG_SYS_FLASH_CFI
   CONFIG_SYS_FSL_ERRATUM_ESDHC135
   CONFIG_SYS_HAS_SERDES
   CONFIG_SYS_L2CACHE_OFF
   CONFIG_SYS_LITTLE_ENDIAN
   CONFIG_SYS_LOAD_ADDR
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
   CONFIG_SYS_NS16550
   CONFIG_SYS_PLLFIN
   CONFIG_SYS_SPI_U_BOOT_OFFS
   CONFIG_TIMER_SYS_TICK_CH
   CONFIG_USB_EHCI_FSL
   CONFIG_U_QE
   CONFIG_VERSION_VARIABLE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00

42 lines
1 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2018-2019 NVIDIA Corporation.
*/
#ifndef _P3450_0000_H
#define _P3450_0000_H
#include <linux/sizes.h>
#include "tegra210-common.h"
/* High-level configuration options */
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA P3450-0000"
/* Board-specific serial config */
#define CONFIG_TEGRA_ENABLE_UARTA
/* Only MMC/PXE/DHCP for now, add USB back in later when supported */
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
/* Environment at end of QSPI, in the VER partition */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
#define BOARD_EXTRA_ENV_SETTINGS \
"preboot=if test -e mmc 1:1 /u-boot-preboot.scr; then " \
"load mmc 1:1 ${scriptaddr} /u-boot-preboot.scr; " \
"source ${scriptaddr}; " \
"fi\0"
/* General networking support */
#include "tegra-common-usb-gadget.h"
#include "tegra-common-post.h"
/* Crystal is 38.4MHz. clk_m runs at half that rate */
#define COUNTER_FREQUENCY 19200000
#endif /* _P3450_0000_H */