mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-25 06:00:43 +00:00
f76750d111
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
18 lines
948 B
Text
18 lines
948 B
Text
CONFIG_ARM=y
|
|
CONFIG_SYS_CONFIG_NAME="exynos78x0-common"
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_ARCH_EXYNOS=y
|
|
CONFIG_SYS_TEXT_BASE=0x40001000
|
|
CONFIG_ARCH_EXYNOS7=y
|
|
CONFIG_TARGET_A5Y17LTE=y
|
|
CONFIG_NR_DRAM_BANKS=12
|
|
CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte"
|
|
CONFIG_SYS_LOAD_ADDR=0x40001000
|
|
CONFIG_FIT=y
|
|
CONFIG_USE_PREBOOT=y
|
|
CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
|
|
# CONFIG_DISPLAY_CPUINFO is not set
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_DM_I2C_GPIO=y
|