Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-12 06:12:58 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/include/configs/ls1021atsn.h
Jianchao Wang 8782122052 Add support for the NXP LS1021A-TSN board 
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.

It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.

Supported boot media: microSD card (via SPL), QSPI flash.

Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).

Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).

To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.

eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>

[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:

- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
  get overwritten during copying of the u-boot.bin payload from MMC to
  DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25 13:13:31 -05:00

250 lines
7.6 KiB
C
Raw Blame History

/* SPDX-License-Identifier: GPL-2.0
* Copyright 2016-2018 NXP Semiconductors
* Copyright 2019 Vladimir Oltean <olteanv@gmail.com>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
#define CONFIG_SYS_FSL_CLK
#define CONFIG_DEEP_SLEEP
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
/* XHCI Support - enabled by default */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
#define DDR_SDRAM_CFG 0x470c0008
#define DDR_CS0_BNDS 0x008000bf
#define DDR_CS0_CONFIG 0x80014302
#define DDR_TIMING_CFG_0 0x50550004
#define DDR_TIMING_CFG_1 0xbcb38c56
#define DDR_TIMING_CFG_2 0x0040d120
#define DDR_TIMING_CFG_3 0x010e1000
#define DDR_TIMING_CFG_4 0x00000001
#define DDR_TIMING_CFG_5 0x03401400
#define DDR_SDRAM_CFG_2 0x00401010
#define DDR_SDRAM_MODE 0x00061c60
#define DDR_SDRAM_MODE_2 0x00180000
#define DDR_SDRAM_INTERVAL 0x18600618
#define DDR_DDR_WRLVL_CNTL 0x8655f605
#define DDR_DDR_WRLVL_CNTL_2 0x05060607
#define DDR_DDR_WRLVL_CNTL_3 0x05050505
#define DDR_DDR_CDR1 0x80040000
#define DDR_DDR_CDR2 0x00000001
#define DDR_SDRAM_CLK_CNTL 0x02000000
#define DDR_DDR_ZQ_CNTL 0x89080600
#define DDR_CS0_CONFIG_2 0
#define DDR_SDRAM_CFG_MEM_EN 0x80000000
#define SDRAM_CFG2_D_INIT 0x00000010
#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
#define SDRAM_CFG2_FRC_SR 0x80000000
#define SDRAM_CFG_BI 0x00000001
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI \
"board/freescale/ls1021atsn/ls102xa_pbi.cfg"
#endif
#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_FSL_PBL_RCW \
"board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg"
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
#endif /* ifdef CONFIG_SECURE_BOOT */
#define CONFIG_SPL_MAX_SIZE 0x1a000
#define CONFIG_SPL_STACK 0x1001d000
#define CONFIG_SPL_PAD_TO 0x1c000
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#ifdef CONFIG_U_BOOT_HDR_SIZE
/*
* HDR would be appended at end of image and copied to DDR along
* with U-Boot image. Here u-boot max. size is 512K. So if binary
* size increases then increase this size in case of secure boot as
* it uses raw U-Boot image instead of FIT image.
*/
#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
#else
#define CONFIG_SYS_MONITOR_LEN 0x100000
#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
#endif
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM 0x80000000
#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#ifndef CONFIG_DM_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#endif
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#define CONFIG_BAUDRATE 115200
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/* QSPI */
#define FSL_QSPI_FLASH_SIZE (1 << 24)
#define FSL_QSPI_FLASH_NUM 2
/* PCIe */
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#endif
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define COUNTER_FREQUENCY 12500000
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 256
#define CONFIG_FSL_DEVICE_DISABLE
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(USB, usb, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"initrd_high=0xffffffff\0" \
"fdt_high=0xffffffff\0" \
"fdt_addr=0x64f00000\0" \
"kernel_addr=0x61000000\0" \
"kernelheader_addr=0x60800000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x80008000\0" \
"kernelheader_size=0x40000\0" \
"fdt_addr_r=0x8f000000\0" \
"ramdisk_addr_r=0xa0000000\0" \
"load_addr=0x80008000\0" \
"kernel_size=0x2800000\0" \
"kernel_addr_sd=0x8000\0" \
"kernel_size_sd=0x14000\0" \
"kernelhdr_addr_sd=0x4000\0" \
"kernelhdr_size_sd=0x10\0" \
BOOTENV \
"boot_scripts=ls1021atsn_boot.scr\0" \
"boot_script_hdr=hdr_ls1021atsn_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"scan_dev_for_boot=" \
"echo Scanning ${devtype} " \
"${devnum}:${distro_bootpart}...; " \
"for prefix in ${boot_prefixes}; do " \
"run scan_dev_for_scripts; " \
"run scan_dev_for_extlinux; " \
"done;" \
"\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"qspi_bootcmd=echo Trying load from qspi..;" \
"sf probe && sf read $load_addr " \
"$kernel_addr $kernel_size; env exists secureboot " \
"&& sf read $kernelheader_addr_r $kernelheader_addr " \
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
"bootm $load_addr#$board\0" \
"sd_bootcmd=echo Trying load from SD ..;" \
"mmcinfo && mmc read $load_addr " \
"$kernel_addr_sd $kernel_size_sd && " \
"env exists secureboot && mmc read $kernelheader_addr_r " \
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
" && esbc_validate ${kernelheader_addr_r};" \
"bootm $load_addr#$board\0"
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR 0x82000000
#define CONFIG_LS102XA_STREAM_ID
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
/* Environment */
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_SD_BOOT)
#define CONFIG_ENV_OFFSET 0x300000
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x20000
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET 0x300000
#define CONFIG_ENV_SECT_SIZE 0x40000
#endif
#define CONFIG_SYS_BOOTM_LEN 0x8000000 /* 128 MB */
#endif
Reference in a new issue View git blame Copy permalink