mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
e37ac717d7
Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
272 lines
7.3 KiB
C
272 lines
7.3 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2014 Soeren Moch <smoch@web.de>
|
|
*/
|
|
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <linux/errno.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
#include <asm/mach-imx/video.h>
|
|
#include <mmc.h>
|
|
#include <fsl_esdhc_imx.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <asm/arch/mxc_hdmi.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define WEAK_PULLUP (PAD_CTL_PUS_47K_UP | \
|
|
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
|
|
PAD_CTL_SRE_SLOW)
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
static iomux_v3_cfg_t const uart1_pads[] = {
|
|
MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const uart2_pads[] = {
|
|
MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const enet_pads[] = {
|
|
MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
/* AR8035 PHY Reset */
|
|
MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const pcie_pads[] = {
|
|
/* W_DISABLE# */
|
|
MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP),
|
|
/* PERST# */
|
|
MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = 2048ul * 1024 * 1024;
|
|
return 0;
|
|
}
|
|
|
|
static void setup_iomux_enet(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
|
|
|
|
/* Reset AR8035 PHY */
|
|
gpio_request(IMX_GPIO_NR(1, 25), "ETH_PHY_RESET");
|
|
gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
|
|
udelay(500);
|
|
gpio_set_value(IMX_GPIO_NR(1, 25), 1);
|
|
}
|
|
|
|
static void setup_pcie(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
|
|
}
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
|
|
imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
|
|
}
|
|
|
|
#ifdef CONFIG_FSL_ESDHC_IMX
|
|
/* set environment device to boot device when booting from SD */
|
|
int board_mmc_get_env_dev(int devno)
|
|
{
|
|
return devno - 1;
|
|
}
|
|
|
|
int board_mmc_get_env_part(int devno)
|
|
{
|
|
return (devno == 3) ? 1 : 0; /* part 0 for SD2 / SD3, part 1 for eMMC */
|
|
}
|
|
#endif /* CONFIG_FSL_ESDHC_IMX */
|
|
|
|
#ifdef CONFIG_VIDEO_IPUV3
|
|
static void do_enable_hdmi(struct display_info_t const *dev)
|
|
{
|
|
imx_enable_hdmi_phy();
|
|
}
|
|
|
|
struct display_info_t const displays[] = {{
|
|
.bus = -1,
|
|
.addr = 0,
|
|
.pixfmt = IPU_PIX_FMT_RGB24,
|
|
.detect = detect_hdmi,
|
|
.enable = do_enable_hdmi,
|
|
.mode = {
|
|
.name = "HDMI",
|
|
/* 1024x768@60Hz (VESA)*/
|
|
.refresh = 60,
|
|
.xres = 1024,
|
|
.yres = 768,
|
|
.pixclock = 15384,
|
|
.left_margin = 160,
|
|
.right_margin = 24,
|
|
.upper_margin = 29,
|
|
.lower_margin = 3,
|
|
.hsync_len = 136,
|
|
.vsync_len = 6,
|
|
.sync = FB_SYNC_EXT,
|
|
.vmode = FB_VMODE_NONINTERLACED
|
|
} } };
|
|
size_t display_count = ARRAY_SIZE(displays);
|
|
|
|
static void setup_display(void)
|
|
{
|
|
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
int reg;
|
|
s32 timeout = 100000;
|
|
|
|
enable_ipu_clock();
|
|
imx_setup_hdmi();
|
|
|
|
/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
|
|
reg = readl(&ccm->analog_pll_video);
|
|
reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
|
|
reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
|
|
reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
|
|
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
|
|
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
while (timeout--)
|
|
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
|
|
break;
|
|
if (timeout < 0)
|
|
printf("Warning: video pll lock timeout!\n");
|
|
|
|
reg = readl(&ccm->analog_pll_video);
|
|
reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
|
|
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
|
|
writel(reg, &ccm->analog_pll_video);
|
|
|
|
/* gate ipu1_di0_clk */
|
|
reg = readl(&ccm->CCGR3);
|
|
reg &= ~MXC_CCM_CCGR3_LDB_DI0_MASK;
|
|
writel(reg, &ccm->CCGR3);
|
|
|
|
/* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
|
|
reg = readl(&ccm->chsccdr);
|
|
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
|
|
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
|
|
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
|
|
reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
|
|
(6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
|
|
(0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
|
|
writel(reg, &ccm->chsccdr);
|
|
|
|
/* enable ipu1_di0_clk */
|
|
reg = readl(&ccm->CCGR3);
|
|
reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
|
|
writel(reg, &ccm->CCGR3);
|
|
}
|
|
#endif /* CONFIG_VIDEO_IPUV3 */
|
|
|
|
static int ar8035_phy_fixup(struct phy_device *phydev)
|
|
{
|
|
unsigned short val;
|
|
|
|
/* To enable AR8035 ouput a 125MHz clk from CLK_25M */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
|
|
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
|
|
val &= 0xffe3;
|
|
val |= 0x18;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
|
|
|
|
/* introduce tx clock delay */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
|
|
val |= 0x0100;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
ar8035_phy_fixup(phydev);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
setup_iomux_enet();
|
|
setup_pcie();
|
|
return cpu_eth_init(bis);
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_CMD_BMODE
|
|
static const struct boot_mode board_boot_modes[] = {
|
|
/* 4 bit bus width */
|
|
{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
|
|
{"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
|
|
/* 8 bit bus width */
|
|
{"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
|
|
{NULL, 0},
|
|
};
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
#ifdef CONFIG_VIDEO_IPUV3
|
|
setup_display();
|
|
#endif
|
|
#ifdef CONFIG_CMD_BMODE
|
|
add_board_boot_modes(board_boot_modes);
|
|
#endif
|
|
return 0;
|
|
}
|