u-boot/board/sbc8641d
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
..
ddr.c SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
Kconfig kconfig: remove redundant "string" type in arch and board Kconfigs 2014-09-13 16:43:55 -04:00
law.c SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
MAINTAINERS Add board MAINTAINERS files 2014-07-30 08:48:06 -04:00
Makefile SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
README Use correct spelling of "U-Boot" 2016-02-06 12:00:59 +01:00
sbc8641d.c SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00

Wind River SBC8641D reference board
===========================

Created 06/14/2007 Joe Hamman
Copyright 2007, Embedded Specialties, Inc.
Copyright 2007 Wind River Systems, Inc.
-----------------------------

1. Building U-Boot
------------------
The SBC8641D code is known to build using ELDK 4.1.

    $ make sbc8641d_config
    Configuring for sbc8641d board...

    $ make


2. Switch and Jumper Settings
-----------------------------
All Jumpers & Switches are in their default positions.  Please refer to
the board documentation for details.  Some settings control CPU voltages
and settings may change with board revisions.

3. Known limitations
--------------------
PCI:
	The PCI command may hang if no boards are present in either slot.

4. Reflashing U-Boot
--------------------
The board has two independent flash devices which can be used for dual
booting, or for U-Boot backup and recovery.  A two pin jumper on the
three pin JP10 determines which device is attached to /CS0 line.

Assuming one device has a functional U-Boot, and the other device has
a recently installed non-functional image, to perform a recovery from
that non-functional image goes essentially as follows:

a) power down the board and jumper JP10 to select the functional image.
b) power on the board and let it get to U-Boot prompt.
c) while on, using static precautions, move JP10 back to the failed image.
d) use "md fff00000" to confirm you are looking at the failed image
e) turn off write protect with "prot off all"
f) get new image, i.e. "tftp 200000 /somepath/u-boot.bin"
g) erase failed image: "erase FFF00000 FFF5FFFF"
h) copy in new image: "cp.b 200000 FFF00000 60000"
i) ensure new image is written: "md fff00000"
k) power cycle the board and confirm new image works.