mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 17:07:38 +00:00
d0399a46e7
Synchronise device trees with linux-next next-20220708. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
817 lines
20 KiB
Text
817 lines
20 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015-2021 DH electronics GmbH
|
|
* Copyright (C) 2018 Marek Vasut <marex@denx.de>
|
|
*/
|
|
|
|
#include <dt-bindings/pwm/pwm.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/clock/imx6qdl-clock.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
i2c0 = &i2c2;
|
|
i2c1 = &i2c1;
|
|
i2c2 = &i2c3;
|
|
mmc0 = &usdhc2;
|
|
mmc1 = &usdhc3;
|
|
mmc2 = &usdhc4;
|
|
mmc3 = &usdhc1;
|
|
rtc0 = &rtc_i2c;
|
|
rtc1 = &snvs_rtc;
|
|
serial0 = &uart1;
|
|
serial1 = &uart5;
|
|
serial2 = &uart4;
|
|
serial3 = &uart2;
|
|
serial4 = &uart3;
|
|
};
|
|
|
|
memory@10000000 { /* Appropriate memory size will be filled by U-Boot */
|
|
device_type = "memory";
|
|
reg = <0x10000000 0x20000000>;
|
|
};
|
|
|
|
reg_3p3v: regulator-3P3V {
|
|
compatible = "regulator-fixed";
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-name = "3P3V";
|
|
};
|
|
|
|
reg_eth_vio: regulator-eth-vio {
|
|
compatible = "regulator-fixed";
|
|
gpio = <&gpio1 7 0>;
|
|
pinctrl-0 = <&pinctrl_enet_vio>;
|
|
pinctrl-names = "default";
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-name = "eth_vio";
|
|
vin-supply = <&sw2_reg>;
|
|
};
|
|
|
|
/* OE pin of the latch is low active */
|
|
reg_latch_oe_on: regulator-latch-oe-on {
|
|
compatible = "regulator-fixed";
|
|
gpio = <&gpio3 22 0>;
|
|
regulator-always-on;
|
|
regulator-name = "latch_oe_on";
|
|
};
|
|
|
|
reg_usb_h1_vbus: regulator-usb-h1-vbus {
|
|
compatible = "regulator-fixed";
|
|
enable-active-high;
|
|
gpio = <&gpio3 31 0>;
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-name = "usb_h1_vbus";
|
|
};
|
|
|
|
reg_usb_otg_vbus: regulator-usb-otg-vbus {
|
|
compatible = "regulator-fixed";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-name = "usb_otg_vbus";
|
|
};
|
|
};
|
|
|
|
&can1 {
|
|
pinctrl-0 = <&pinctrl_flexcan1>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
/*
|
|
* Special SoM hardware required which uses the pins from micro SD card. The
|
|
* pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2
|
|
* Tx and Rx are routed to the DHCOM UART1 rts/cts pins. So to enable can2 on
|
|
* the board device tree file, the micro SD card must be disabled and the uart1
|
|
* rts/cts must be disabled or output on other DHCOM pins.
|
|
*/
|
|
&can2 {
|
|
pinctrl-0 = <&pinctrl_flexcan2>;
|
|
pinctrl-names = "default";
|
|
status = "disabled";
|
|
};
|
|
|
|
&ecspi1 {
|
|
cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>;
|
|
pinctrl-0 = <&pinctrl_ecspi1>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
flash@0 { /* S25FL116K */
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
m25p,fast-read;
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
};
|
|
};
|
|
|
|
&ecspi2 {
|
|
cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
|
|
pinctrl-0 = <&pinctrl_ecspi2>;
|
|
pinctrl-names = "default";
|
|
status = "disabled";
|
|
};
|
|
|
|
&fec {
|
|
phy-mode = "rmii";
|
|
phy-handle = <ðphy0>;
|
|
pinctrl-0 = <&pinctrl_enet_100M>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
|
|
compatible = "ethernet-phy-id0007.c0f0",
|
|
"ethernet-phy-ieee802.3-c22";
|
|
interrupt-parent = <&gpio4>;
|
|
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
|
|
pinctrl-0 = <&pinctrl_ethphy0>;
|
|
pinctrl-names = "default";
|
|
reg = <0>;
|
|
reset-assert-us = <500>;
|
|
reset-deassert-us = <500>;
|
|
reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
|
|
smsc,disable-energy-detect; /* Make plugin detection reliable */
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio1 {
|
|
gpio-line-names =
|
|
"", "", "DHCOM-A", "", "DHCOM-B", "DHCOM-C", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"DHCOM-R", "DHCOM-S", "DHCOM-Q", "DHCOM-T", "DHCOM-U", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&gpio2 {
|
|
gpio-line-names =
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"SOM-HW2", "", "", "SOM-HW0", "", "SOM-MEM1", "SOM-MEM0", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&gpio3 {
|
|
gpio-line-names =
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "DHCOM-G", "", "", "", "";
|
|
};
|
|
|
|
&gpio4 {
|
|
gpio-line-names =
|
|
"", "", "", "", "", "DHCOM-E", "DHCOM-INT", "DHCOM-H",
|
|
"DHCOM-I", "DHCOM-L", "", "", "", "", "", "",
|
|
"", "", "", "", "DHCOM-F", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&gpio5 {
|
|
gpio-line-names =
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "DHCOM-V", "DHCOM-W", "", "DHCOM-O", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&gpio6 {
|
|
gpio-line-names =
|
|
"", "", "", "DHCOM-D", "", "", "SOM-HW1", "",
|
|
"", "", "", "", "", "", "DHCOM-J", "DHCOM-K",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&gpio7 {
|
|
gpio-line-names =
|
|
"DHCOM-M", "DHCOM-N", "", "", "", "", "", "",
|
|
"", "", "", "", "", "DHCOM-P", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&i2c1 {
|
|
/*
|
|
* Info: According to erratum ERR007805 clock frequency limit is 375000.
|
|
* The erratum for i.MX6S/DL is here [1] and for i.MX6Q/D is here [2].
|
|
* [1] https://www.nxp.com/docs/en/errata/IMX6SDLCE.pdf
|
|
* [2] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
|
|
*/
|
|
clock-frequency = <100000>;
|
|
pinctrl-0 = <&pinctrl_i2c1>;
|
|
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
|
pinctrl-names = "default", "gpio";
|
|
scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c2 {
|
|
/* Info: Clock frequency limit is 375000 (for details see i2c1) */
|
|
clock-frequency = <100000>;
|
|
pinctrl-0 = <&pinctrl_i2c2>;
|
|
pinctrl-1 = <&pinctrl_i2c2_gpio>;
|
|
pinctrl-names = "default", "gpio";
|
|
scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c3 {
|
|
/* Info: Clock frequency limit is 375000 (for details see i2c1) */
|
|
clock-frequency = <100000>;
|
|
pinctrl-0 = <&pinctrl_i2c3>;
|
|
pinctrl-1 = <&pinctrl_i2c3_gpio>;
|
|
pinctrl-names = "default", "gpio";
|
|
scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
status = "okay";
|
|
|
|
ltc3676: pmic@3c {
|
|
compatible = "lltc,ltc3676";
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
|
|
pinctrl-0 = <&pinctrl_pmic>;
|
|
pinctrl-names = "default";
|
|
reg = <0x3c>;
|
|
|
|
regulators {
|
|
sw1_reg: sw1 {
|
|
lltc,fb-voltage-divider = <100000 110000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-max-microvolt = <1527272>;
|
|
regulator-min-microvolt = <787500>;
|
|
regulator-ramp-delay = <7000>;
|
|
regulator-suspend-mem-microvolt = <1040000>;
|
|
};
|
|
|
|
sw2_reg: sw2 {
|
|
lltc,fb-voltage-divider = <100000 28000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-max-microvolt = <3657142>;
|
|
regulator-min-microvolt = <1885714>;
|
|
regulator-ramp-delay = <7000>;
|
|
};
|
|
|
|
sw3_reg: sw3 {
|
|
lltc,fb-voltage-divider = <100000 110000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-max-microvolt = <1527272>;
|
|
regulator-min-microvolt = <787500>;
|
|
regulator-ramp-delay = <7000>;
|
|
regulator-suspend-mem-microvolt = <980000>;
|
|
};
|
|
|
|
sw4_reg: sw4 {
|
|
lltc,fb-voltage-divider = <100000 93100>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-max-microvolt = <1659291>;
|
|
regulator-min-microvolt = <855571>;
|
|
regulator-ramp-delay = <7000>;
|
|
};
|
|
|
|
ldo1_reg: ldo1 {
|
|
lltc,fb-voltage-divider = <102000 29400>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-max-microvolt = <3240306>;
|
|
regulator-min-microvolt = <3240306>;
|
|
};
|
|
|
|
ldo2_reg: ldo2 {
|
|
lltc,fb-voltage-divider = <100000 41200>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-max-microvolt = <2484708>;
|
|
regulator-min-microvolt = <2484708>;
|
|
};
|
|
};
|
|
};
|
|
|
|
touchscreen@49 { /* TSC2004 */
|
|
compatible = "ti,tsc2004";
|
|
interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
|
|
pinctrl-0 = <&pinctrl_tsc2004>;
|
|
pinctrl-names = "default";
|
|
reg = <0x49>;
|
|
vio-supply = <®_3p3v>;
|
|
status = "disabled";
|
|
};
|
|
|
|
eeprom@50 {
|
|
compatible = "atmel,24c02";
|
|
pagesize = <16>;
|
|
reg = <0x50>;
|
|
};
|
|
|
|
rtc_i2c: rtc@56 {
|
|
compatible = "microcrystal,rv3029";
|
|
interrupt-parent = <&gpio7>;
|
|
interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
|
|
pinctrl-0 = <&pinctrl_rtc>;
|
|
pinctrl-names = "default";
|
|
reg = <0x56>;
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
pinctrl-0 = <&pinctrl_pcie>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pwm1 {
|
|
pinctrl-0 = <&pinctrl_pwm1>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
®_arm {
|
|
vin-supply = <&sw3_reg>;
|
|
};
|
|
|
|
®_pu {
|
|
vin-supply = <&sw1_reg>;
|
|
};
|
|
|
|
®_soc {
|
|
vin-supply = <&sw1_reg>;
|
|
};
|
|
|
|
®_vdd1p1 {
|
|
vin-supply = <&sw2_reg>;
|
|
};
|
|
|
|
®_vdd2p5 {
|
|
vin-supply = <&sw2_reg>;
|
|
};
|
|
|
|
&uart1 { /* DHCOM UART1 */
|
|
dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
|
|
dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
|
|
dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
|
|
rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
|
|
pinctrl-0 = <&pinctrl_uart1>;
|
|
pinctrl-names = "default";
|
|
uart-has-rtscts;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart4 { /* DHCOM UART3 */
|
|
pinctrl-0 = <&pinctrl_uart4>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&uart5 { /* DHCOM UART2 */
|
|
pinctrl-0 = <&pinctrl_uart5>;
|
|
pinctrl-names = "default";
|
|
uart-has-rtscts;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh1 {
|
|
dr_mode = "host";
|
|
pinctrl-0 = <&pinctrl_usbh1>;
|
|
pinctrl-names = "default";
|
|
vbus-supply = <®_usb_h1_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbotg {
|
|
disable-over-current;
|
|
dr_mode = "otg";
|
|
pinctrl-0 = <&pinctrl_usbotg>;
|
|
pinctrl-names = "default";
|
|
vbus-supply = <®_usb_otg_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usdhc2 { /* External SD card via DHCOM */
|
|
cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
|
|
keep-power-in-suspend;
|
|
pinctrl-0 = <&pinctrl_usdhc2>;
|
|
pinctrl-names = "default";
|
|
status = "disabled";
|
|
};
|
|
|
|
&usdhc3 { /* Micro SD card on module */
|
|
cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
|
|
fsl,wp-controller;
|
|
keep-power-in-suspend;
|
|
pinctrl-0 = <&pinctrl_usdhc3>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&usdhc4 { /* eMMC on module */
|
|
bus-width = <8>;
|
|
keep-power-in-suspend;
|
|
no-1-8-v;
|
|
non-removable;
|
|
pinctrl-0 = <&pinctrl_usdhc4>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&weim {
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
fsl,weim-cs-gpr = <&gpr>;
|
|
pinctrl-0 = <&pinctrl_weim &pinctrl_weim_cs0 &pinctrl_weim_cs1>;
|
|
pinctrl-names = "default";
|
|
/* It is necessary to setup 2x 64MB otherwise setting gpr fails */
|
|
ranges = <0 0 0x08000000 0x04000000>, /* CS0 */
|
|
<1 0 0x0c000000 0x04000000>; /* CS1 */
|
|
status = "disabled";
|
|
};
|
|
|
|
&iomuxc {
|
|
pinctrl-0 = <
|
|
&pinctrl_hog_base
|
|
&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
|
|
&pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
|
|
&pinctrl_dhcom_g &pinctrl_dhcom_h &pinctrl_dhcom_i
|
|
&pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
|
|
&pinctrl_dhcom_m &pinctrl_dhcom_n &pinctrl_dhcom_o
|
|
&pinctrl_dhcom_p &pinctrl_dhcom_q &pinctrl_dhcom_r
|
|
&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
|
|
&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
|
|
>;
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl_hog_base: hog-base-grp {
|
|
fsl,pins = <
|
|
/* GPIOs for memory coding */
|
|
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x120b0
|
|
MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x120b0
|
|
/* GPIOs for hardware coding */
|
|
MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x120b0
|
|
MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x120b0
|
|
MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x120b0
|
|
>;
|
|
};
|
|
|
|
/* DHCOM GPIOs */
|
|
pinctrl_dhcom_a: dhcom-a-grp {
|
|
fsl,pins = <MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_b: dhcom-b-grp {
|
|
fsl,pins = <MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_c: dhcom-c-grp {
|
|
fsl,pins = <MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_d: dhcom-d-grp {
|
|
fsl,pins = <MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_e: dhcom-e-grp {
|
|
fsl,pins = <MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_f: dhcom-f-grp {
|
|
fsl,pins = <MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_g: dhcom-g-grp {
|
|
fsl,pins = <MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_h: dhcom-h-grp {
|
|
fsl,pins = <MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_i: dhcom-i-grp {
|
|
fsl,pins = <MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_j: dhcom-j-grp {
|
|
fsl,pins = <MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_k: dhcom-k-grp {
|
|
fsl,pins = <MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_l: dhcom-l-grp {
|
|
fsl,pins = <MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_m: dhcom-m-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_n: dhcom-n-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_o: dhcom-o-grp {
|
|
fsl,pins = <MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_p: dhcom-p-grp {
|
|
fsl,pins = <MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_q: dhcom-q-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_r: dhcom-r-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_s: dhcom-s-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_t: dhcom-t-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_u: dhcom-u-grp {
|
|
fsl,pins = <MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_v: dhcom-v-grp {
|
|
fsl,pins = <MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_w: dhcom-w-grp {
|
|
fsl,pins = <MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_dhcom_int: dhcom-int-grp {
|
|
fsl,pins = <MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x400120b0>;
|
|
};
|
|
|
|
pinctrl_ecspi1: ecspi1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
|
|
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
|
|
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
|
|
MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
|
|
MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_ecspi2: ecspi2-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1
|
|
MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1
|
|
MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1
|
|
MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_enet_100M: enet-100M-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
|
|
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
|
|
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
|
|
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
|
|
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
|
|
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
|
|
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
|
|
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
|
|
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
|
|
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
|
|
>;
|
|
};
|
|
|
|
pinctrl_enet_vio: enet-vio-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x120b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_ethphy0: ethphy0-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0xb0 /* Reset */
|
|
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0xb1 /* Int */
|
|
>;
|
|
};
|
|
|
|
pinctrl_flexcan1: flexcan1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
|
|
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_flexcan2: flexcan2-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0
|
|
MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c1: i2c1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
|
|
MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c1_gpio: i2c1-gpio-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x4001b8b1
|
|
MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x4001b8b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c2: i2c2-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
|
|
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c2_gpio: i2c2-gpio-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b1
|
|
MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c3: i2c3-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
|
|
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c3_gpio: i2c3-gpio-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x4001b8b1
|
|
MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b8b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_pcie: pcie-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b1 /* Wake */
|
|
>;
|
|
};
|
|
|
|
pinctrl_pmic: pmic-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_pwm1: pwm1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_rtc: rtc-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x120b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_tsc2004: tsc2004-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x120b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_uart1: uart1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x4001b0b1
|
|
MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1
|
|
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x4001b0b1
|
|
MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x4001b0b1
|
|
MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x4001b0b1
|
|
MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x4001b0b1
|
|
MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
|
|
MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_uart4: uart4-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
|
|
MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_uart5: uart5-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
|
|
MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
|
|
MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x1b0b1
|
|
MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x4001b0b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_usbh1: usbh1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x120b0
|
|
MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b0b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_usbotg: usbotg-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc2: usdhc2-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x120b0
|
|
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
|
|
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
|
|
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
|
|
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
|
|
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
|
|
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc3: usdhc3-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
|
|
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
|
|
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
|
|
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
|
|
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
|
|
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
|
|
MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x120b0
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc4: usdhc4-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
|
|
MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
|
|
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
|
|
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
|
|
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
|
|
MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
|
|
MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
|
|
MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
|
|
MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
|
|
MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
|
|
>;
|
|
};
|
|
|
|
pinctrl_weim: weim-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0a6
|
|
MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0a6
|
|
MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0a6
|
|
MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0a6
|
|
MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0a6
|
|
MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0a6
|
|
MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0a6
|
|
MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0a6
|
|
MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0a6
|
|
MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0a6
|
|
MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0a6
|
|
MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0a6
|
|
MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0a6
|
|
MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0a6
|
|
MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0a6
|
|
MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0a6
|
|
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0
|
|
MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb060 /* LE */
|
|
MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0a6
|
|
MX6QDL_PAD_EIM_RW__EIM_RW 0xb0a6 /* WE */
|
|
>;
|
|
};
|
|
|
|
pinctrl_weim_cs0: weim-cs0-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
|
|
>;
|
|
};
|
|
|
|
pinctrl_weim_cs1: weim-cs1-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
|
|
>;
|
|
};
|
|
};
|