u-boot/include/configs/tb100.h
Tom Rini e985eb14ac Convert CONFIG_CMD_ASKENV et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04 18:10:02 -04:00

60 lines
1.3 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2011-2014 Pierrick Hascoet, Abilis Systems
*/
#ifndef _CONFIG_TB100_H_
#define _CONFIG_TB100_H_
#include <linux/sizes.h>
/*
* Memory configuration
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_SDRAM_SIZE SZ_128M
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_MALLOC_LEN SZ_128K
#define CONFIG_SYS_BOOTM_LEN SZ_32M
#define CONFIG_SYS_LOAD_ADDR 0x82000000
/*
* UART configuration
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_CLK 166666666
/*
* Even though the board houses Realtek RTL8211E PHY
* corresponding PHY driver (drivers/net/phy/realtek.c) behaves unexpectedly.
* In particular "parse_status" reports link is down.
*
* Until Realtek PHY driver is fixed fall back to generic PHY driver
* which implements all required functionality and behaves much more stable.
*
*
*/
/*
* Ethernet configuration
*/
#define ETH0_BASE_ADDRESS 0xFE100000
#define ETH1_BASE_ADDRESS 0xFE110000
/*
* Environment configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
/*
* Console configuration
*/
#endif /* _CONFIG_TB100_H_ */