Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-11 15:37:23 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/include/configs/lx2160a_common.h
Tom Rini eaf6ea6a1d Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h 
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
  pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
  set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
  GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
  board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:19 -04:00

260 lines
7.7 KiB
C
Raw Blame History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018-2021 NXP
*/
#ifndef __LX2_COMMON_H
#define __LX2_COMMON_H
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
#define CONFIG_FSL_MEMAC
#define CONFIG_SYS_FLASH_BASE 0x20000000
/* DDR */
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
#define CONFIG_SYS_SDRAM_SIZE 0x200000000UL
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define SPD_EEPROM_ADDRESS3 0x53
#define SPD_EEPROM_ADDRESS4 0x54
#define SPD_EEPROM_ADDRESS5 0x55
#define SPD_EEPROM_ADDRESS6 0x56
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
#define CONFIG_SYS_MONITOR_LEN (936 * 1024)
/* Miscellaneous configurable options */
/* SMP Definitinos */
#define CPU_RELEASE_ADDR secondary_boot_addr
/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
/* Serial Port */
#define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4)
#define CONFIG_SYS_SERIAL0 0x21c0000
#define CONFIG_SYS_SERIAL1 0x21d0000
#define CONFIG_SYS_SERIAL2 0x21e0000
#define CONFIG_SYS_SERIAL3 0x21f0000
/*below might needs to be removed*/
#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \
(void *)CONFIG_SYS_SERIAL1, \
(void *)CONFIG_SYS_SERIAL2, \
(void *)CONFIG_SYS_SERIAL3 }
/* MC firmware */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
#endif
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
#define I2C_MUX_CH_DEFAULT 0x8
/* RTC */
#define RTC
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
/* Qixis */
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
/* PCI */
#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#endif
/* SATA */
#ifdef CONFIG_SCSI
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
#endif
/* USB */
#ifdef CONFIG_USB_HOST
#ifndef CONFIG_TARGET_LX2162AQDS
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
#endif
#define COUNTER_FREQUENCY_REAL (get_board_sys_clk() / 4)
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/* Initial environment variables */
#define XSPI_MC_INIT_CMD \
"sf probe 0:0 && " \
"sf read 0x80640000 0x640000 0x80000 && " \
"sf read $fdt_addr_r 0xf00000 0x100000 && " \
"env exists secureboot && " \
"esbc_validate 0x80640000 && " \
"esbc_validate 0x80680000; " \
"sf read 0x80a00000 0xa00000 0x300000 && " \
"sf read 0x80e00000 0xe00000 0x100000; " \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD_MC_INIT_CMD \
"mmc read 0x80a00000 0x5000 0x1200;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"mmc read $fdt_addr_r 0x7800 0x800;" \
"env exists secureboot && " \
"mmc read 0x80640000 0x3200 0x20 && " \
"mmc read 0x80680000 0x3400 0x20 && " \
"esbc_validate 0x80640000 && " \
"esbc_validate 0x80680000 ;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD2_MC_INIT_CMD \
"mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"mmc read $fdt_addr_r 0x7800 0x800;" \
"env exists secureboot && " \
"mmc read 0x80640000 0x3200 0x20 && " \
"mmc read 0x80680000 0x3400 0x20 && " \
"esbc_validate 0x80640000 && " \
"esbc_validate 0x80680000 ;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x1000000\0" \
"kernelheader_start=0x600000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"kernelheader_size=0x40000\0" \
"fdt_addr_r=0x90000000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_addr_sd=0x8000\0" \
"kernelhdr_addr_sd=0x3000\0" \
"kernel_size_sd=0x14000\0" \
"kernelhdr_size_sd=0x20\0" \
"console=ttyAMA0,38400n8\0" \
BOOTENV \
"mcmemsize=0x70000000\0" \
XSPI_MC_INIT_CMD \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0"
#define XSPI_NOR_BOOTCOMMAND \
"sf probe 0:0; " \
"sf read 0x806c0000 0x6c0000 0x40000; " \
"env exists mcinitcmd && env exists secureboot" \
" && esbc_validate 0x806c0000; " \
"sf read 0x80d00000 0xd00000 0x100000; " \
"env exists mcinitcmd && " \
"fsl_mc lazyapply dpl 0x80d00000; " \
"run distro_bootcmd;run xspi_bootcmd; " \
"env exists secureboot && esbc_halt;"
#define SD_BOOTCOMMAND \
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80d00000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
" && mmc read 0x806C0000 0x3600 0x20 " \
"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80d00000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
#define SD2_BOOTCOMMAND \
"mmc dev 1; env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80d00000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
" && mmc read 0x806C0000 0x3600 0x20 " \
"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80d00000;" \
"run distro_bootcmd;run sd2_bootcmd;" \
"env exists secureboot && esbc_halt;"
#ifdef CONFIG_CMD_USB
#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_DEVICES_USB(func)
#endif
#ifdef CONFIG_MMC
#define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
#else
#define BOOT_TARGET_DEVICES_MMC(func)
#endif
#ifdef CONFIG_SCSI
#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
#else
#define BOOT_TARGET_DEVICES_SCSI(func)
#endif
#ifdef CONFIG_CMD_DHCP
#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
#else
#define BOOT_TARGET_DEVICES_DHCP(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_DEVICES_USB(func) \
BOOT_TARGET_DEVICES_MMC(func, 0) \
BOOT_TARGET_DEVICES_MMC(func, 1) \
BOOT_TARGET_DEVICES_SCSI(func) \
BOOT_TARGET_DEVICES_DHCP(func)
#include <config_distro_bootcmd.h>
#endif /* __LX2_COMMON_H */
Reference in a new issue View git blame Copy permalink