u-boot/drivers/usb/host/xhci-exynos5.c
Julius Werner 4a271cb1b4 exynos: usb: Switch USB VBUS GPIOs to be device tree configured
Some Exynos boards, such as the SMDK5250, control USB port power through
a GPIO pin. For now this had been hardcoded in the exynos5-dt board
file, but not all boards use the same pin, requiring local changes to
support different boards.

This patch moves the GPIO initialization into the USB host controller
drivers which they belong to, and uses the samsung,vbus-gpio parameter
in the device tree to configure it.

Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-10-20 23:42:38 +02:00

327 lines
7.8 KiB
C

/*
* SAMSUNG EXYNOS5 USB HOST XHCI Controller
*
* Copyright (C) 2012 Samsung Electronics Co.Ltd
* Vivek Gautam <gautam.vivek@samsung.com>
* Vikas Sajjan <vikas.sajjan@samsung.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* This file is a conglomeration for DWC3-init sequence and further
* exynos5 specific PHY-init sequence.
*/
#include <common.h>
#include <fdtdec.h>
#include <libfdt.h>
#include <malloc.h>
#include <usb.h>
#include <watchdog.h>
#include <asm/arch/cpu.h>
#include <asm/arch/power.h>
#include <asm/arch/xhci-exynos.h>
#include <asm/gpio.h>
#include <asm-generic/errno.h>
#include <linux/compat.h>
#include <linux/usb/dwc3.h>
#include "xhci.h"
/* Declare global data pointer */
DECLARE_GLOBAL_DATA_PTR;
/**
* Contains pointers to register base addresses
* for the usb controller.
*/
struct exynos_xhci {
struct exynos_usb3_phy *usb3_phy;
struct xhci_hccr *hcd;
struct dwc3 *dwc3_reg;
struct fdt_gpio_state vbus_gpio;
};
static struct exynos_xhci exynos;
#ifdef CONFIG_OF_CONTROL
static int exynos_usb3_parse_dt(const void *blob, struct exynos_xhci *exynos)
{
fdt_addr_t addr;
unsigned int node;
int depth;
node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_XHCI);
if (node <= 0) {
debug("XHCI: Can't get device node for xhci\n");
return -ENODEV;
}
/*
* Get the base address for XHCI controller from the device node
*/
addr = fdtdec_get_addr(blob, node, "reg");
if (addr == FDT_ADDR_T_NONE) {
debug("Can't get the XHCI register base address\n");
return -ENXIO;
}
exynos->hcd = (struct xhci_hccr *)addr;
/* Vbus gpio */
fdtdec_decode_gpio(blob, node, "samsung,vbus-gpio", &exynos->vbus_gpio);
depth = 0;
node = fdtdec_next_compatible_subnode(blob, node,
COMPAT_SAMSUNG_EXYNOS5_USB3_PHY, &depth);
if (node <= 0) {
debug("XHCI: Can't get device node for usb3-phy controller\n");
return -ENODEV;
}
/*
* Get the base address for usbphy from the device node
*/
exynos->usb3_phy = (struct exynos_usb3_phy *)fdtdec_get_addr(blob, node,
"reg");
if (exynos->usb3_phy == NULL) {
debug("Can't get the usbphy register address\n");
return -ENXIO;
}
return 0;
}
#endif
static void exynos5_usb3_phy_init(struct exynos_usb3_phy *phy)
{
u32 reg;
/* enabling usb_drd phy */
set_usbdrd_phy_ctrl(POWER_USB_DRD_PHY_CTRL_EN);
/* Reset USB 3.0 PHY */
writel(0x0, &phy->phy_reg0);
clrbits_le32(&phy->phy_param0,
/* Select PHY CLK source */
PHYPARAM0_REF_USE_PAD |
/* Set Loss-of-Signal Detector sensitivity */
PHYPARAM0_REF_LOSLEVEL_MASK);
setbits_le32(&phy->phy_param0, PHYPARAM0_REF_LOSLEVEL);
writel(0x0, &phy->phy_resume);
/*
* Setting the Frame length Adj value[6:1] to default 0x20
* See xHCI 1.0 spec, 5.2.4
*/
setbits_le32(&phy->link_system,
LINKSYSTEM_XHCI_VERSION_CONTROL |
LINKSYSTEM_FLADJ(0x20));
/* Set Tx De-Emphasis level */
clrbits_le32(&phy->phy_param1, PHYPARAM1_PCS_TXDEEMPH_MASK);
setbits_le32(&phy->phy_param1, PHYPARAM1_PCS_TXDEEMPH);
setbits_le32(&phy->phy_batchg, PHYBATCHG_UTMI_CLKSEL);
/* PHYTEST POWERDOWN Control */
clrbits_le32(&phy->phy_test,
PHYTEST_POWERDOWN_SSP |
PHYTEST_POWERDOWN_HSP);
/* UTMI Power Control */
writel(PHYUTMI_OTGDISABLE, &phy->phy_utmi);
/* Use core clock from main PLL */
reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
/* Default 24Mhz crystal clock */
PHYCLKRST_FSEL(FSEL_CLKSEL_24M) |
PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
PHYCLKRST_SSC_REFCLKSEL(0x88) |
/* Force PortReset of PHY */
PHYCLKRST_PORTRESET |
/* Digital power supply in normal operating mode */
PHYCLKRST_RETENABLEN |
/* Enable ref clock for SS function */
PHYCLKRST_REF_SSP_EN |
/* Enable spread spectrum */
PHYCLKRST_SSC_EN |
/* Power down HS Bias and PLL blocks in suspend mode */
PHYCLKRST_COMMONONN;
writel(reg, &phy->phy_clk_rst);
/* giving time to Phy clock to settle before resetting */
udelay(10);
reg &= ~PHYCLKRST_PORTRESET;
writel(reg, &phy->phy_clk_rst);
}
static void exynos5_usb3_phy_exit(struct exynos_usb3_phy *phy)
{
setbits_le32(&phy->phy_utmi,
PHYUTMI_OTGDISABLE |
PHYUTMI_FORCESUSPEND |
PHYUTMI_FORCESLEEP);
clrbits_le32(&phy->phy_clk_rst,
PHYCLKRST_REF_SSP_EN |
PHYCLKRST_SSC_EN |
PHYCLKRST_COMMONONN);
/* PHYTEST POWERDOWN Control to remove leakage current */
setbits_le32(&phy->phy_test,
PHYTEST_POWERDOWN_SSP |
PHYTEST_POWERDOWN_HSP);
/* disabling usb_drd phy */
set_usbdrd_phy_ctrl(POWER_USB_DRD_PHY_CTRL_DISABLE);
}
void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode)
{
clrsetbits_le32(&dwc3_reg->g_ctl,
DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG),
DWC3_GCTL_PRTCAPDIR(mode));
}
static void dwc3_core_soft_reset(struct dwc3 *dwc3_reg)
{
/* Before Resetting PHY, put Core in Reset */
setbits_le32(&dwc3_reg->g_ctl,
DWC3_GCTL_CORESOFTRESET);
/* Assert USB3 PHY reset */
setbits_le32(&dwc3_reg->g_usb3pipectl[0],
DWC3_GUSB3PIPECTL_PHYSOFTRST);
/* Assert USB2 PHY reset */
setbits_le32(&dwc3_reg->g_usb2phycfg,
DWC3_GUSB2PHYCFG_PHYSOFTRST);
mdelay(100);
/* Clear USB3 PHY reset */
clrbits_le32(&dwc3_reg->g_usb3pipectl[0],
DWC3_GUSB3PIPECTL_PHYSOFTRST);
/* Clear USB2 PHY reset */
clrbits_le32(&dwc3_reg->g_usb2phycfg,
DWC3_GUSB2PHYCFG_PHYSOFTRST);
/* After PHYs are stable we can take Core out of reset state */
clrbits_le32(&dwc3_reg->g_ctl,
DWC3_GCTL_CORESOFTRESET);
}
static int dwc3_core_init(struct dwc3 *dwc3_reg)
{
u32 reg;
u32 revision;
unsigned int dwc3_hwparams1;
revision = readl(&dwc3_reg->g_snpsid);
/* This should read as U3 followed by revision number */
if ((revision & DWC3_GSNPSID_MASK) != 0x55330000) {
puts("this is not a DesignWare USB3 DRD Core\n");
return -EINVAL;
}
dwc3_core_soft_reset(dwc3_reg);
dwc3_hwparams1 = readl(&dwc3_reg->g_hwparams1);
reg = readl(&dwc3_reg->g_ctl);
reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
reg &= ~DWC3_GCTL_DISSCRAMBLE;
switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc3_hwparams1)) {
case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
reg &= ~DWC3_GCTL_DSBLCLKGTNG;
break;
default:
debug("No power optimization available\n");
}
/*
* WORKAROUND: DWC3 revisions <1.90a have a bug
* where the device can fail to connect at SuperSpeed
* and falls back to high-speed mode which causes
* the device to enter a Connect/Disconnect loop
*/
if ((revision & DWC3_REVISION_MASK) < 0x190a)
reg |= DWC3_GCTL_U2RSTECN;
writel(reg, &dwc3_reg->g_ctl);
return 0;
}
static int exynos_xhci_core_init(struct exynos_xhci *exynos)
{
int ret;
exynos5_usb3_phy_init(exynos->usb3_phy);
ret = dwc3_core_init(exynos->dwc3_reg);
if (ret) {
debug("failed to initialize core\n");
return -EINVAL;
}
/* We are hard-coding DWC3 core to Host Mode */
dwc3_set_mode(exynos->dwc3_reg, DWC3_GCTL_PRTCAP_HOST);
return 0;
}
static void exynos_xhci_core_exit(struct exynos_xhci *exynos)
{
exynos5_usb3_phy_exit(exynos->usb3_phy);
}
int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor **hcor)
{
struct exynos_xhci *ctx = &exynos;
int ret;
#ifdef CONFIG_OF_CONTROL
exynos_usb3_parse_dt(gd->fdt_blob, ctx);
#else
ctx->usb3_phy = (struct exynos_usb3_phy *)samsung_get_base_usb3_phy();
ctx->hcd = (struct xhci_hccr *)samsung_get_base_usb_xhci();
#endif
ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
#ifdef CONFIG_OF_CONTROL
/* setup the Vbus gpio here */
if (!fdtdec_setup_gpio(&ctx->vbus_gpio))
gpio_direction_output(ctx->vbus_gpio.gpio, 1);
#endif
ret = exynos_xhci_core_init(ctx);
if (ret) {
puts("XHCI: failed to initialize controller\n");
return -EINVAL;
}
*hccr = (ctx->hcd);
*hcor = (struct xhci_hcor *)((uint32_t) *hccr
+ HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
debug("Exynos5-xhci: init hccr %x and hcor %x hc_length %d\n",
(uint32_t)*hccr, (uint32_t)*hcor,
(uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
return 0;
}
void xhci_hcd_stop(int index)
{
struct exynos_xhci *ctx = &exynos;
exynos_xhci_core_exit(ctx);
}