mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-25 06:00:43 +00:00
2fe88d4522
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
452 lines
13 KiB
C
452 lines
13 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) Freescale Semiconductor, Inc. 2006.
|
|
*
|
|
* (C) Copyright 2010
|
|
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
|
|
*/
|
|
/*
|
|
* ve8313 board configuration file
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1
|
|
#define CONFIG_MPC831x 1
|
|
#define CONFIG_MPC8313 1
|
|
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE 1
|
|
#define CONFIG_FSL_ELBC 1
|
|
|
|
/*
|
|
* On-board devices
|
|
*
|
|
*/
|
|
#define CONFIG_83XX_CLKIN 32000000 /* in Hz */
|
|
|
|
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
|
|
|
|
#define CONFIG_SYS_IMMR 0xE0000000
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00001000
|
|
#define CONFIG_SYS_MEMTEST_END 0x07000000
|
|
|
|
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */
|
|
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */
|
|
|
|
/*
|
|
* Device configurations
|
|
*/
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
|
|
/*
|
|
* Manually set up DDR parameters, as this board does not
|
|
* have the SPD connected to I2C.
|
|
*/
|
|
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
|
|
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
|
|
| CSCONFIG_AP \
|
|
| CSCONFIG_ODT_RD_NEVER \
|
|
| CSCONFIG_ODT_WR_ALL \
|
|
| CSCONFIG_ROW_BIT_13 \
|
|
| CSCONFIG_COL_BIT_10)
|
|
/* 0x80840102 */
|
|
|
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
|
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
|
|
| (0 << TIMING_CFG0_WRT_SHIFT) \
|
|
| (3 << TIMING_CFG0_RRT_SHIFT) \
|
|
| (2 << TIMING_CFG0_WWT_SHIFT) \
|
|
| (7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
|
|
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
|
|
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
|
|
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
|
|
/* 0x0e720802 */
|
|
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
|
|
| (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
|
|
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
|
|
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
|
|
| (6 << TIMING_CFG1_REFREC_SHIFT) \
|
|
| (2 << TIMING_CFG1_WRREC_SHIFT) \
|
|
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
|
|
| (2 << TIMING_CFG1_WRTORD_SHIFT))
|
|
/* 0x26256222 */
|
|
#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
|
|
| (5 << TIMING_CFG2_CPO_SHIFT) \
|
|
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
|
|
| (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
|
|
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
|
|
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
|
|
| (7 << TIMING_CFG2_FOUR_ACT_SHIFT))
|
|
/* 0x029028c7 */
|
|
#define CONFIG_SYS_DDR_INTERVAL ((0x320 << SDRAM_INTERVAL_REFINT_SHIFT) \
|
|
| (0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
|
|
/* 0x03202000 */
|
|
#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \
|
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
|
| SDRAM_CFG_DBW_32)
|
|
/* 0x43080000 */
|
|
#define CONFIG_SYS_SDRAM_CFG2 0x00401000
|
|
#define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \
|
|
| (0x0232 << SDRAM_MODE_SD_SHIFT))
|
|
/* 0x44400232 */
|
|
#define CONFIG_SYS_DDR_MODE_2 0x8000C000
|
|
|
|
#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
|
/*0x02000000*/
|
|
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
|
|
| DDRCDR_PZ_NOMZ \
|
|
| DDRCDR_NZ_NOMZ \
|
|
| DDRCDR_M_ODR)
|
|
/* 0x73000002 */
|
|
|
|
/*
|
|
* FLASH on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000
|
|
#define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
|
|
|
|
#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \
|
|
| BR_PS_16 /* 16 bit */ \
|
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
|
| BR_V) /* valid */
|
|
#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
|
|
| OR_GPCM_CSNT \
|
|
| OR_GPCM_ACS_DIV4 \
|
|
| OR_GPCM_SCY_5 \
|
|
| OR_GPCM_TRLX_SET \
|
|
| OR_GPCM_EAD)
|
|
/* 0xfe000c55 */
|
|
|
|
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
|
|
#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
|
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
|
|
|
|
/*
|
|
* Local Bus LCRR and LBCR regs
|
|
*/
|
|
#define CONFIG_SYS_LCRR_EADC LCRR_EADC_3
|
|
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
|
|
|
|
#define CONFIG_SYS_LBC_LBCR 0x00040000
|
|
|
|
#define CONFIG_SYS_LBC_MRTPR 0x20000000
|
|
|
|
/*
|
|
* NAND settings
|
|
*/
|
|
#define CONFIG_SYS_NAND_BASE 0x61000000
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_NAND_FSL_ELBC 1
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
|
|
|
|
#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
|
|
| BR_PS_8 \
|
|
| BR_DECC_CHK_GEN \
|
|
| BR_MS_FCM \
|
|
| BR_V) /* valid */
|
|
/* 0x61000c21 */
|
|
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \
|
|
| OR_FCM_BCTLD \
|
|
| OR_FCM_CHT \
|
|
| OR_FCM_SCY_2 \
|
|
| OR_FCM_RST \
|
|
| OR_FCM_TRLX)
|
|
/* 0xffff90ac */
|
|
|
|
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
|
|
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
|
|
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
|
|
|
|
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
|
|
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
|
|
|
|
#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
|
|
#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
|
|
|
|
/* CS2 NvRAM */
|
|
#define CONFIG_SYS_BR2_PRELIM (0x60000000 \
|
|
| BR_PS_8 \
|
|
| BR_V)
|
|
/* 0x60000801 */
|
|
#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \
|
|
| OR_GPCM_CSNT \
|
|
| OR_GPCM_XACS \
|
|
| OR_GPCM_SCY_3 \
|
|
| OR_GPCM_TRLX_SET \
|
|
| OR_GPCM_EHTR_SET \
|
|
| OR_GPCM_EAD)
|
|
/* 0xfffe0937 */
|
|
/* local bus read write buffer mapping SRAM@0x64000000 */
|
|
#define CONFIG_SYS_BR3_PRELIM (0x62000000 \
|
|
| BR_PS_16 \
|
|
| BR_V)
|
|
/* 0x62001001 */
|
|
|
|
#define CONFIG_SYS_OR3_PRELIM (OR_AM_32MB \
|
|
| OR_GPCM_CSNT \
|
|
| OR_GPCM_XACS \
|
|
| OR_GPCM_SCY_15 \
|
|
| OR_GPCM_TRLX_SET \
|
|
| OR_GPCM_EHTR_SET \
|
|
| OR_GPCM_EAD)
|
|
/* 0xfe0009f7 */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
|
|
|
|
#if defined(CONFIG_PCI)
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
|
|
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
|
|
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
|
|
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
|
|
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
|
|
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
|
|
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
|
#endif
|
|
|
|
/*
|
|
* TSEC
|
|
*/
|
|
|
|
#define CONFIG_TSEC1
|
|
#ifdef CONFIG_TSEC1
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_TSEC1_NAME "TSEC1"
|
|
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
|
#define TSEC1_PHY_ADDR 0x01
|
|
#define TSEC1_FLAGS 0
|
|
#define TSEC1_PHYIDX 0
|
|
#endif
|
|
|
|
/* Options are: TSEC[0-1] */
|
|
#define CONFIG_ETHPRIME "TSEC1"
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x4000
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_OFFSET_REDUND \
|
|
(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 256 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
/* Initial Memory map for Linux*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
|
|
|
|
/* 0x64050000 */
|
|
#define CONFIG_SYS_HRCW_LOW (\
|
|
0x20000000 /* reserved, must be set */ |\
|
|
HRCWL_DDRCM |\
|
|
HRCWL_CSB_TO_CLKIN_4X1 | \
|
|
HRCWL_CORE_TO_CSB_2_5X1)
|
|
|
|
/* 0xa0600004 */
|
|
#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
|
|
HRCWH_PCI_ARBITER_ENABLE | \
|
|
HRCWH_CORE_ENABLE | \
|
|
HRCWH_FROM_0X00000100 | \
|
|
HRCWH_BOOTSEQ_DISABLE |\
|
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
|
HRCWH_ROM_LOC_LOCAL_16BIT | \
|
|
HRCWH_TSEC1M_IN_MII | \
|
|
HRCWH_BIG_ENDIAN | \
|
|
HRCWH_LALE_EARLY)
|
|
|
|
/* System IO Config */
|
|
#define CONFIG_SYS_SICRH (0x01000000 | \
|
|
SICRH_ETSEC2_B | \
|
|
SICRH_ETSEC2_C | \
|
|
SICRH_ETSEC2_D | \
|
|
SICRH_ETSEC2_E | \
|
|
SICRH_ETSEC2_F | \
|
|
SICRH_ETSEC2_G | \
|
|
SICRH_TSOBI1 | \
|
|
SICRH_TSOBI2)
|
|
/* 0x010fff03 */
|
|
#define CONFIG_SYS_SICRL (SICRL_LBC | \
|
|
SICRL_SPI_A | \
|
|
SICRL_SPI_B | \
|
|
SICRL_SPI_C | \
|
|
SICRL_SPI_D | \
|
|
SICRL_ETSEC2_A)
|
|
/* 0x33fc0003) */
|
|
|
|
#define CONFIG_SYS_HID0_INIT 0x000000000
|
|
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
|
|
HID0_ENABLE_INSTRUCTION_CACHE)
|
|
|
|
#define CONFIG_SYS_HID2 HID2_HBE
|
|
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
/* DDR @ 0x00000000 */
|
|
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
|
|
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
|
|
| BATU_BL_256M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
|
|
#if defined(CONFIG_PCI)
|
|
/* PCI @ 0x80000000 */
|
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
|
|
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
|
|
| BATU_BL_256M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
|
|
| BATL_PP_RW \
|
|
| BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
|
|
| BATU_BL_256M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#else
|
|
#define CONFIG_SYS_IBAT1L (0)
|
|
#define CONFIG_SYS_IBAT1U (0)
|
|
#define CONFIG_SYS_IBAT2L (0)
|
|
#define CONFIG_SYS_IBAT2U (0)
|
|
#endif
|
|
|
|
/* PCI2 not supported on 8313 */
|
|
#define CONFIG_SYS_IBAT3L (0)
|
|
#define CONFIG_SYS_IBAT3U (0)
|
|
#define CONFIG_SYS_IBAT4L (0)
|
|
#define CONFIG_SYS_IBAT4U (0)
|
|
|
|
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
|
|
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
|
|
| BATL_PP_RW \
|
|
| BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
|
|
| BATU_BL_256M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
|
|
/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
|
|
#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* FPGA, SRAM, NAND @ 0x60000000 */
|
|
#define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
|
|
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
|
|
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
|
|
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
|
|
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
|
|
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
|
|
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
|
|
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
|
|
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
|
|
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
|
|
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
|
|
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
|
|
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
|
|
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
|
|
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
|
|
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
|
|
|
|
#define CONFIG_NETDEV eth0
|
|
|
|
#define CONFIG_HOSTNAME "ve8313"
|
|
#define CONFIG_UBOOTPATH ve8313/u-boot.bin
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=" __stringify(CONFIG_NETDEV) "\0" \
|
|
"ethprime=" __stringify(CONFIG_TSEC1_NAME) "\0" \
|
|
"u-boot=" __stringify(CONFIG_UBOOTPATH) "\0" \
|
|
"u-boot_addr_r=100000\0" \
|
|
"load=tftp ${u-boot_addr_r} ${u-boot}\0" \
|
|
"update=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \
|
|
" +${filesize};" \
|
|
"erase " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
|
|
"cp.b ${u-boot_addr_r} " __stringify(CONFIG_SYS_FLASH_BASE) \
|
|
" ${filesize};" \
|
|
"protect on " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \
|
|
|
|
#endif /* __CONFIG_H */
|