mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-23 11:33:32 +00:00
9d40799551
Notes: - Board-dependend code for RPXLITE and RPXCLASSIC-based boards placed to the drivers/rpx_pmcia.c file to avoid duplication. Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c). - drivers/i82365.c has been split into two parts located at board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are the only boards using CONFIG_82365). - Changes were tested for clean build and *very* *few* boards.
93 lines
2.3 KiB
C
93 lines
2.3 KiB
C
#include <common.h>
|
|
#include <mpc8xx.h>
|
|
#include <pcmcia.h>
|
|
|
|
#undef CONFIG_PCMCIA
|
|
|
|
#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
|
|
#define CONFIG_PCMCIA
|
|
#endif
|
|
|
|
#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
|
|
#define CONFIG_PCMCIA
|
|
#endif
|
|
|
|
#ifdef CONFIG_PCMCIA
|
|
|
|
#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
|
|
|
|
int pcmcia_voltage_set (int slot, int vcc, int vpp)
|
|
{ /* Do nothing */
|
|
return 0;
|
|
}
|
|
|
|
int pcmcia_hardware_enable (int slot)
|
|
{
|
|
volatile immap_t *immap;
|
|
volatile cpm8xx_t *cp;
|
|
volatile pcmconf8xx_t *pcmp;
|
|
volatile sysconf8xx_t *sysp;
|
|
uint reg, mask;
|
|
|
|
debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
|
|
|
|
immap = (immap_t *) CFG_IMMR;
|
|
sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
|
|
pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
|
|
cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
|
|
|
|
/* clear interrupt state, and disable interrupts */
|
|
pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
|
|
pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
|
|
|
|
/*
|
|
* Disable interrupts, DMA, and PCMCIA buffers
|
|
* (isolate the interface) and assert RESET signal
|
|
*/
|
|
debug ("Disable PCMCIA buffers and assert RESET\n");
|
|
reg = 0;
|
|
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
|
|
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
|
|
PCMCIA_PGCRX (_slot_) = reg;
|
|
udelay (500);
|
|
|
|
/*
|
|
* Make sure there is a card in the slot,
|
|
* then configure the interface.
|
|
*/
|
|
udelay (10000);
|
|
debug ("[%d] %s: PIPR(%p)=0x%x\n",
|
|
__LINE__, __FUNCTION__,
|
|
&(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
|
|
if (pcmp->pcmc_pipr & 0x98000000) {
|
|
printf (" No Card found\n");
|
|
return (1);
|
|
}
|
|
|
|
mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
|
|
reg = pcmp->pcmc_pipr;
|
|
debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
|
|
reg,
|
|
(reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
|
|
(reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
|
|
|
|
debug ("Enable PCMCIA buffers and stop RESET\n");
|
|
reg = PCMCIA_PGCRX (_slot_);
|
|
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
|
|
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
|
|
PCMCIA_PGCRX (_slot_) = reg;
|
|
|
|
udelay (250000); /* some cards need >150 ms to come up :-( */
|
|
|
|
debug ("# hardware_enable done\n");
|
|
|
|
return 0;
|
|
}
|
|
#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
|
|
int pcmcia_hardware_disable(int slot)
|
|
{
|
|
return 0; /* No hardware to disable */
|
|
}
|
|
#endif
|
|
|
|
#endif /* CONFIG_PCMCIA */
|