mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 00:21:06 +00:00
34c3c0e01d
* Added comments and a printf to warn that PCI-X won't work at 33MHz Patch by Andy Fleming 17-Mar-2006 Signed-off-by: Andy Fleming <afleming@freescale.com>
303 lines
10 KiB
Text
303 lines
10 KiB
Text
Motorola MPC8540ADS and MPC8560ADS board
|
|
|
|
Created 10/15/03 Xianghua Xiao
|
|
Updated 13-July-2004 Jon Loeliger
|
|
-----------------------------------------
|
|
|
|
0. Toolchain
|
|
|
|
The Binutils in current ELDK toolchain will not support MPC85xx
|
|
chip. You need to use binutils-2.14.tar.bz2 (or newer) from
|
|
http://ftp.gnu.org/gnu/binutils.
|
|
|
|
The 8540/8560 ADS code base is known to compile using:
|
|
gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)
|
|
|
|
|
|
1. SWITCH SETTINGS & JUMPERS
|
|
|
|
1.0 Nomenclature
|
|
|
|
For some reason, the HW designers describe the switch settings
|
|
in terms of 0 and 1, and then map that to physical switches where
|
|
the label "On" refers to logic 0 and "Off" (unlabeled) is logic 1.
|
|
Luckily, we're SW types and virtual settings are handled daily.
|
|
|
|
The switches for the Rev A board are numbered differently than
|
|
for the Pilot board. Oh yeah.
|
|
|
|
Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
|
|
bits may contribute to signals that are numbered based at 0,
|
|
and some of those signals may be high-bit-number-0 too. Heed
|
|
well the names and labels and do not get confused.
|
|
|
|
"Off" == 1
|
|
"On" == 0
|
|
|
|
SW18 is switch 18 as silk-screened onto the board.
|
|
SW4[8] is the bit labled 8 on Switch 4.
|
|
SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2
|
|
SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3
|
|
|
|
1.1 For the MPC85xxADS Pilot Board
|
|
|
|
First, make sure the board default setting is consistent with the document
|
|
shipped with your board. Then apply the following changes:
|
|
SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used)
|
|
SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
|
|
SW11[2]='OFF for 8560, ON for 8540' (toggle 8540.8560 mode)
|
|
SW11[7]='ON' (rev2), 'OFF' (rev1)
|
|
SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
|
|
SW22[1-4]="OFF OFF ON OFF"
|
|
SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
|
|
J1 = "Enable Prog" (Make sure your flash is programmable for development)
|
|
|
|
If you want to test PCI functionality with a 33Mhz PCI card, you will
|
|
have to change the system clock from the default 66Mhz to 33Mhz by
|
|
setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
|
|
double your platform clock(SW6) because the system clock is now only
|
|
half of its original value. For example, if at 66MHz your system
|
|
clock showed SW6[0:1] = 01, then at 33MHz SW6[0:1] it should be 10.
|
|
|
|
SW17[8] ------+ SW6
|
|
SW15[1] ----+ | [0:1]
|
|
V V V V
|
|
33MHz 1 1 1 0
|
|
66MHz 0 0 0 1
|
|
|
|
Hmmm... That SW6 setting description is incomplete but it works.
|
|
|
|
|
|
1.3 For the MPC85xxADS Rev A Board
|
|
|
|
As shipped, the board should be a 33MHz PCI bus with a CPU Clock
|
|
rate of 825 +/- fuzz:
|
|
|
|
Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC: 82 MHz
|
|
|
|
For 33MHz PCI, the switch settings should be like this:
|
|
|
|
SW18[7:1] = 0100001 = M==33 => 33MHz
|
|
SW18[8] = 1 => PWD Divider == 16
|
|
SW16[1:2] = 11 => N == 16 as PWD==1
|
|
|
|
Use the magical formula:
|
|
Fout (MHz) = 16 * M / N = 16 * 33 / 16 = 33 MHz
|
|
|
|
SW7[1:4] = 1010 = 10 => 10 x 33 = 330 CCB Sysclk
|
|
SW7[5:6] = 01 => 5:2 x 330 = 825 Core clock
|
|
|
|
|
|
For 66MHz PCI, the switch settings should be like this:
|
|
|
|
SW18[7:1] = 0100001 = M==33 => 33MHz
|
|
SW18[8] = 0 => PWD Divider == 1
|
|
SW16[1:2] = 01 => N == 8 as PWD == 0
|
|
|
|
Use the magical formula:
|
|
Fout (MHz) = 16 * M / N = 16 * 33 / 8 = 66 MHz
|
|
|
|
SW7[1:4] = 0101 = 5 => 5 x 66 = 330 CCB Sysclk
|
|
SW7[5:6] = 01 => 5:2 x 330 = 825 Core clock
|
|
|
|
In order to use PCI-X (only in the first PCI slot. The one with
|
|
the RIO connector), you need to set SW1[4] (config) to 1 (off).
|
|
Also, configure the board to run PCI at 66 MHz.
|
|
|
|
2. MEMORY MAP TO WORK WITH LINUX KERNEL
|
|
|
|
2.1. For the initial bringup, we adopted a consistent memory scheme
|
|
between u-boot and linux kernel, you can customize it based on your
|
|
system requirements:
|
|
|
|
0x0000_0000 0x7fff_ffff DDR 2G
|
|
0x8000_0000 0x9fff_ffff PCI MEM 512M
|
|
0xc000_0000 0xdfff_ffff Rapid IO 512M
|
|
0xe000_0000 0xe00f_ffff CCSR 1M
|
|
0xe200_0000 0xe2ff_ffff PCI IO 16M
|
|
0xf000_0000 0xf7ff_ffff SDRAM 128M
|
|
0xf800_0000 0xf80f_ffff BCSR 1M
|
|
0xff00_0000 0xffff_ffff FLASH (boot bank) 16M
|
|
|
|
2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You
|
|
can download them from linuxppc-2.4 public source. Please make sure the
|
|
kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two
|
|
default configuration files as your starting points to configure the
|
|
kernel:
|
|
arch/ppc/configs/mpc8540_ads_defconfig
|
|
arch/ppc/configs/mpc8560_ads_defconfig
|
|
|
|
3. DEFINITIONS AND COMPILATION
|
|
|
|
3.1 Explanation on NEW definitions in:
|
|
include/configs/MPC8540ADS.h
|
|
include/configs/MPC8560ADS.h
|
|
|
|
CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, AMCC 440, etc)
|
|
CONFIG_E500 BOOKE e500 family(Motorola)
|
|
CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives
|
|
CONFIG_MPC8540 MPC8540 specific
|
|
CONFIG_MPC8540ADS MPC8540ADS board specific
|
|
CONFIG_MPC8560ADS MPC8560ADS board specific
|
|
CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking
|
|
CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can
|
|
also manual config the DDR after undef this
|
|
definition.
|
|
CONFIG_DDR_ECC only for ECC DDR module
|
|
CONFIG_DDR_DLL DLL fix on some ADS boards needed for more
|
|
stability.
|
|
CONFIG_HAS_FEC If an FEC is on chip, set to 1, else 0.
|
|
|
|
Other than the above definitions, the rest in the config files are
|
|
straightforward.
|
|
|
|
|
|
3.2 Compilation
|
|
|
|
Assuming you're using BASH shell:
|
|
|
|
export CROSS_COMPILE=your-cross-compile-prefix
|
|
cd u-boot
|
|
make distclean
|
|
make MPC8560ADS_config (or make MPC8540ADS_config)
|
|
make
|
|
|
|
4. Notes:
|
|
|
|
4.1 When connecting with kermit, the following commands must be present.in
|
|
your .kermrc file. These are especially important when booting as
|
|
MPC8560, as the serial console will not work without them:
|
|
|
|
set speed 115200
|
|
set carrier-watch off
|
|
set handshake none
|
|
set flow-control none
|
|
robust
|
|
|
|
|
|
4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC
|
|
ethernet. If that happens, you can try the following steps to make
|
|
network work:
|
|
|
|
MPC8560ADS>tftp 1000000 pImage
|
|
(if it hangs, use Ctrl-C to quit)
|
|
MPC8560ADS>nm fdf24524
|
|
>0
|
|
>1
|
|
>. (to quit this memory operation)
|
|
MPC8560ADS>tftp 1000000 pImage
|
|
|
|
4.3 If you're one of the early developers using the Rev1 8540/8560 chips,
|
|
please use U-Boot 1.0.0, as the newer silicon will only support Rev2
|
|
and future revisions of 8540/8560.
|
|
|
|
|
|
4.4 Reflash U-boot Image using U-boot
|
|
|
|
tftp 10000 u-boot.bin
|
|
protect off fff80000 ffffffff
|
|
erase fff80000 ffffffff
|
|
cp.b 10000 fff80000 80000
|
|
|
|
|
|
4.5 Reflash U-Boot with a BDI-2000
|
|
|
|
BDI> erase 0xFFF80000 0x4000 0x20
|
|
BDI> prog 0xfff80000 u-boot.bin.8560ads
|
|
BDI> verify
|
|
|
|
|
|
5. Screen dump MPC8540ADS board
|
|
|
|
U-Boot 1.1.2(pq3-20040707-0) (Jul 6 2004 - 17:34:25)
|
|
|
|
Freescale PowerPC
|
|
Core: E500, Version: 2.0, (0x80200020)
|
|
System: 8540, Version: 2.0, (0x80300020)
|
|
Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC: 82 MHz
|
|
L1 D-cache 32KB, L1 I-cache 32KB enabled.
|
|
Board: ADS
|
|
PCI1: 32 bit, 66 MHz (compiled)
|
|
I2C: ready
|
|
DRAM: Initializing
|
|
SDRAM: 64 MB
|
|
DDR: 256 MB
|
|
FLASH: 16 MB
|
|
L2 cache enabled: 256KB
|
|
*** Warning - bad CRC, using default environment
|
|
|
|
In: serial
|
|
Out: serial
|
|
Err: serial
|
|
Net: MOTO ENET0: PHY is Marvell 88E1011S (1410c62)
|
|
MOTO ENET1: PHY is Marvell 88E1011S (1410c62)
|
|
MOTO ENET2: PHY is Davicom DM9161E (181b881)
|
|
MOTO ENET0, MOTO ENET1, MOTO ENET2
|
|
Hit any key to stop autoboot: 0
|
|
=>
|
|
=> fli
|
|
|
|
Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
|
|
Size: 16 MB in 64 Sectors
|
|
Sector Start Addresses:
|
|
FF000000 FF040000 FF080000 FF0C0000 FF100000
|
|
FF140000 FF180000 FF1C0000 FF200000 FF240000
|
|
FF280000 FF2C0000 FF300000 FF340000 FF380000
|
|
FF3C0000 FF400000 FF440000 FF480000 FF4C0000
|
|
FF500000 FF540000 FF580000 FF5C0000 FF600000
|
|
FF640000 FF680000 FF6C0000 FF700000 FF740000
|
|
FF780000 FF7C0000 FF800000 FF840000 FF880000
|
|
FF8C0000 FF900000 FF940000 FF980000 FF9C0000
|
|
FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000
|
|
FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000
|
|
FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000
|
|
FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000
|
|
FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO)
|
|
|
|
=> bdinfo
|
|
memstart = 0x00000000
|
|
memsize = 0x10000000
|
|
flashstart = 0xFF000000
|
|
flashsize = 0x01000000
|
|
flashoffset = 0x00000000
|
|
sramstart = 0x00000000
|
|
sramsize = 0x00000000
|
|
immr_base = 0xE0000000
|
|
bootflags = 0xE4013F80
|
|
intfreq = 825 MHz
|
|
busfreq = 330 MHz
|
|
ethaddr = 00:E0:0C:00:00:FD
|
|
eth1addr = 00:E0:0C:00:01:FD
|
|
eth2addr = 00:E0:0C:00:02:FD
|
|
IP addr = 192.168.1.253
|
|
baudrate = 115200 bps
|
|
|
|
|
|
=> printenv
|
|
bootcmd=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
|
|
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;bootm $loadaddr $ramdiskaddr
|
|
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
|
|
bootdelay=10
|
|
baudrate=115200
|
|
loads_echo=1
|
|
ethaddr=00:E0:0C:00:00:FD
|
|
eth1addr=00:E0:0C:00:01:FD
|
|
eth2addr=00:E0:0C:00:02:FD
|
|
ipaddr=192.168.1.253
|
|
serverip=192.168.1.1
|
|
rootpath=/nfsroot
|
|
gatewayip=192.168.1.1
|
|
netmask=255.255.255.0
|
|
hostname=unknown
|
|
bootfile=your.uImage
|
|
loadaddr=200000
|
|
netdev=eth0
|
|
consoledev=ttyS0
|
|
ramdiskaddr=400000
|
|
ramdiskfile=your.ramdisk.u-boot
|
|
stdin=serial
|
|
stdout=serial
|
|
stderr=serial
|
|
ethact=MOTO ENET0
|
|
|
|
Environment size: 1020/8188 bytes
|