mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-23 11:33:32 +00:00
a706029410
Most DM based SPI host controller drivers use SPI_XFER_BEGIN and SPI_XFER_END flags to enable/disable slave chip select. This patch extends MMC SPI driver to pass SPI_XFER_BEGIN flag when MMC command is send at start and pass SPI_XFER_END flag using a dummy transfer (of bitlen = 0) at the end of MMC command. Suggested-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Tested-by: Sagar Kadam <sagar.kadam@sifive.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
430 lines
10 KiB
C
430 lines
10 KiB
C
/*
|
|
* generic mmc spi driver
|
|
*
|
|
* Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
|
|
* Copyright 2019 Bhargav Shah <bhargavshah1988@gmail.com>
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
#include <common.h>
|
|
#include <errno.h>
|
|
#include <malloc.h>
|
|
#include <part.h>
|
|
#include <mmc.h>
|
|
#include <stdlib.h>
|
|
#include <u-boot/crc.h>
|
|
#include <linux/crc7.h>
|
|
#include <asm/byteorder.h>
|
|
#include <dm.h>
|
|
#include <spi.h>
|
|
|
|
/* MMC/SD in SPI mode reports R1 status always */
|
|
#define R1_SPI_IDLE BIT(0)
|
|
#define R1_SPI_ERASE_RESET BIT(1)
|
|
#define R1_SPI_ILLEGAL_COMMAND BIT(2)
|
|
#define R1_SPI_COM_CRC BIT(3)
|
|
#define R1_SPI_ERASE_SEQ BIT(4)
|
|
#define R1_SPI_ADDRESS BIT(5)
|
|
#define R1_SPI_PARAMETER BIT(6)
|
|
/* R1 bit 7 is always zero, reuse this bit for error */
|
|
#define R1_SPI_ERROR BIT(7)
|
|
|
|
/* Response tokens used to ack each block written: */
|
|
#define SPI_MMC_RESPONSE_CODE(x) ((x) & 0x1f)
|
|
#define SPI_RESPONSE_ACCEPTED ((2 << 1)|1)
|
|
#define SPI_RESPONSE_CRC_ERR ((5 << 1)|1)
|
|
#define SPI_RESPONSE_WRITE_ERR ((6 << 1)|1)
|
|
|
|
/* Read and write blocks start with these tokens and end with crc;
|
|
* on error, read tokens act like a subset of R2_SPI_* values.
|
|
*/
|
|
/* single block write multiblock read */
|
|
#define SPI_TOKEN_SINGLE 0xfe
|
|
/* multiblock write */
|
|
#define SPI_TOKEN_MULTI_WRITE 0xfc
|
|
/* terminate multiblock write */
|
|
#define SPI_TOKEN_STOP_TRAN 0xfd
|
|
|
|
/* MMC SPI commands start with a start bit "0" and a transmit bit "1" */
|
|
#define MMC_SPI_CMD(x) (0x40 | (x))
|
|
|
|
/* bus capability */
|
|
#define MMC_SPI_VOLTAGE (MMC_VDD_32_33 | MMC_VDD_33_34)
|
|
#define MMC_SPI_MIN_CLOCK 400000 /* 400KHz to meet MMC spec */
|
|
#define MMC_SPI_MAX_CLOCK 25000000 /* SD/MMC legacy speed */
|
|
|
|
/* timeout value */
|
|
#define CMD_TIMEOUT 8
|
|
#define READ_TIMEOUT 3000000 /* 1 sec */
|
|
#define WRITE_TIMEOUT 3000000 /* 1 sec */
|
|
|
|
struct mmc_spi_priv {
|
|
struct spi_slave *spi;
|
|
struct mmc_config cfg;
|
|
struct mmc mmc;
|
|
};
|
|
|
|
static int mmc_spi_sendcmd(struct udevice *dev,
|
|
ushort cmdidx, u32 cmdarg, u32 resp_type,
|
|
u8 *resp, u32 resp_size,
|
|
bool resp_match, u8 resp_match_value)
|
|
{
|
|
int i, rpos = 0, ret = 0;
|
|
u8 cmdo[7], r;
|
|
|
|
debug("%s: cmd%d cmdarg=0x%x resp_type=0x%x "
|
|
"resp_size=%d resp_match=%d resp_match_value=0x%x\n",
|
|
__func__, cmdidx, cmdarg, resp_type,
|
|
resp_size, resp_match, resp_match_value);
|
|
|
|
cmdo[0] = 0xff;
|
|
cmdo[1] = MMC_SPI_CMD(cmdidx);
|
|
cmdo[2] = cmdarg >> 24;
|
|
cmdo[3] = cmdarg >> 16;
|
|
cmdo[4] = cmdarg >> 8;
|
|
cmdo[5] = cmdarg;
|
|
cmdo[6] = (crc7(0, &cmdo[1], 5) << 1) | 0x01;
|
|
ret = dm_spi_xfer(dev, sizeof(cmdo) * 8, cmdo, NULL, SPI_XFER_BEGIN);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = dm_spi_xfer(dev, 1 * 8, NULL, &r, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (!resp || !resp_size)
|
|
return 0;
|
|
|
|
debug("%s: cmd%d", __func__, cmdidx);
|
|
|
|
if (resp_match) {
|
|
r = ~resp_match_value;
|
|
i = CMD_TIMEOUT;
|
|
while (i--) {
|
|
ret = dm_spi_xfer(dev, 1 * 8, NULL, &r, 0);
|
|
if (ret)
|
|
return ret;
|
|
debug(" resp%d=0x%x", rpos, r);
|
|
rpos++;
|
|
if (r == resp_match_value)
|
|
break;
|
|
}
|
|
if (!i && (r != resp_match_value))
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
for (i = 0; i < resp_size; i++) {
|
|
if (i == 0 && resp_match) {
|
|
resp[i] = resp_match_value;
|
|
continue;
|
|
}
|
|
ret = dm_spi_xfer(dev, 1 * 8, NULL, &r, 0);
|
|
if (ret)
|
|
return ret;
|
|
debug(" resp%d=0x%x", rpos, r);
|
|
rpos++;
|
|
resp[i] = r;
|
|
}
|
|
|
|
debug("\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mmc_spi_readdata(struct udevice *dev,
|
|
void *xbuf, u32 bcnt, u32 bsize)
|
|
{
|
|
u16 crc;
|
|
u8 *buf = xbuf, r1;
|
|
int i, ret = 0;
|
|
|
|
while (bcnt--) {
|
|
for (i = 0; i < READ_TIMEOUT; i++) {
|
|
ret = dm_spi_xfer(dev, 1 * 8, NULL, &r1, 0);
|
|
if (ret)
|
|
return ret;
|
|
if (r1 == SPI_TOKEN_SINGLE)
|
|
break;
|
|
}
|
|
debug("%s: data tok%d 0x%x\n", __func__, i, r1);
|
|
if (r1 == SPI_TOKEN_SINGLE) {
|
|
ret = dm_spi_xfer(dev, bsize * 8, NULL, buf, 0);
|
|
if (ret)
|
|
return ret;
|
|
ret = dm_spi_xfer(dev, 2 * 8, NULL, &crc, 0);
|
|
if (ret)
|
|
return ret;
|
|
#ifdef CONFIG_MMC_SPI_CRC_ON
|
|
if (be16_to_cpu(crc16_ccitt(0, buf, bsize)) != crc) {
|
|
debug("%s: data crc error\n", __func__);
|
|
r1 = R1_SPI_COM_CRC;
|
|
break;
|
|
}
|
|
#endif
|
|
r1 = 0;
|
|
} else {
|
|
r1 = R1_SPI_ERROR;
|
|
break;
|
|
}
|
|
buf += bsize;
|
|
}
|
|
|
|
if (r1 & R1_SPI_COM_CRC)
|
|
ret = -ECOMM;
|
|
else if (r1) /* other errors */
|
|
ret = -ETIMEDOUT;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int mmc_spi_writedata(struct udevice *dev, const void *xbuf,
|
|
u32 bcnt, u32 bsize, int multi)
|
|
{
|
|
const u8 *buf = xbuf;
|
|
u8 r1, tok[2];
|
|
u16 crc;
|
|
int i, ret = 0;
|
|
|
|
tok[0] = 0xff;
|
|
tok[1] = multi ? SPI_TOKEN_MULTI_WRITE : SPI_TOKEN_SINGLE;
|
|
|
|
while (bcnt--) {
|
|
#ifdef CONFIG_MMC_SPI_CRC_ON
|
|
crc = cpu_to_be16(crc16_ccitt(0, (u8 *)buf, bsize));
|
|
#endif
|
|
dm_spi_xfer(dev, 2 * 8, tok, NULL, 0);
|
|
dm_spi_xfer(dev, bsize * 8, buf, NULL, 0);
|
|
dm_spi_xfer(dev, 2 * 8, &crc, NULL, 0);
|
|
for (i = 0; i < CMD_TIMEOUT; i++) {
|
|
dm_spi_xfer(dev, 1 * 8, NULL, &r1, 0);
|
|
if ((r1 & 0x10) == 0) /* response token */
|
|
break;
|
|
}
|
|
debug("%s: data tok%d 0x%x\n", __func__, i, r1);
|
|
if (SPI_MMC_RESPONSE_CODE(r1) == SPI_RESPONSE_ACCEPTED) {
|
|
debug("%s: data accepted\n", __func__);
|
|
for (i = 0; i < WRITE_TIMEOUT; i++) { /* wait busy */
|
|
dm_spi_xfer(dev, 1 * 8, NULL, &r1, 0);
|
|
if (i && r1 == 0xff) {
|
|
r1 = 0;
|
|
break;
|
|
}
|
|
}
|
|
if (i == WRITE_TIMEOUT) {
|
|
debug("%s: data write timeout 0x%x\n",
|
|
__func__, r1);
|
|
r1 = R1_SPI_ERROR;
|
|
break;
|
|
}
|
|
} else {
|
|
debug("%s: data error 0x%x\n", __func__, r1);
|
|
r1 = R1_SPI_COM_CRC;
|
|
break;
|
|
}
|
|
buf += bsize;
|
|
}
|
|
if (multi && bcnt == -1) { /* stop multi write */
|
|
tok[1] = SPI_TOKEN_STOP_TRAN;
|
|
dm_spi_xfer(dev, 2 * 8, tok, NULL, 0);
|
|
for (i = 0; i < WRITE_TIMEOUT; i++) { /* wait busy */
|
|
dm_spi_xfer(dev, 1 * 8, NULL, &r1, 0);
|
|
if (i && r1 == 0xff) {
|
|
r1 = 0;
|
|
break;
|
|
}
|
|
}
|
|
if (i == WRITE_TIMEOUT) {
|
|
debug("%s: data write timeout 0x%x\n", __func__, r1);
|
|
r1 = R1_SPI_ERROR;
|
|
}
|
|
}
|
|
|
|
if (r1 & R1_SPI_COM_CRC)
|
|
ret = -ECOMM;
|
|
else if (r1) /* other errors */
|
|
ret = -ETIMEDOUT;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dm_mmc_spi_set_ios(struct udevice *dev)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int dm_mmc_spi_request(struct udevice *dev, struct mmc_cmd *cmd,
|
|
struct mmc_data *data)
|
|
{
|
|
int i, multi, ret = 0;
|
|
u8 *resp = NULL;
|
|
u32 resp_size = 0;
|
|
bool resp_match = false;
|
|
u8 resp8 = 0, resp40[5] = { 0 }, resp_match_value = 0;
|
|
|
|
dm_spi_claim_bus(dev);
|
|
|
|
for (i = 0; i < 4; i++)
|
|
cmd->response[i] = 0;
|
|
|
|
switch (cmd->cmdidx) {
|
|
case SD_CMD_APP_SEND_OP_COND:
|
|
case MMC_CMD_SEND_OP_COND:
|
|
resp = &resp8;
|
|
resp_size = sizeof(resp8);
|
|
cmd->cmdarg = 0x40000000;
|
|
break;
|
|
case SD_CMD_SEND_IF_COND:
|
|
resp = (u8 *)&resp40[0];
|
|
resp_size = sizeof(resp40);
|
|
resp_match = true;
|
|
resp_match_value = R1_SPI_IDLE;
|
|
break;
|
|
case MMC_CMD_SPI_READ_OCR:
|
|
resp = (u8 *)&resp40[0];
|
|
resp_size = sizeof(resp40);
|
|
break;
|
|
case MMC_CMD_SEND_STATUS:
|
|
case MMC_CMD_SET_BLOCKLEN:
|
|
case MMC_CMD_SPI_CRC_ON_OFF:
|
|
case MMC_CMD_STOP_TRANSMISSION:
|
|
resp = &resp8;
|
|
resp_size = sizeof(resp8);
|
|
resp_match = true;
|
|
resp_match_value = 0x0;
|
|
break;
|
|
case MMC_CMD_SEND_CSD:
|
|
case MMC_CMD_SEND_CID:
|
|
case MMC_CMD_READ_SINGLE_BLOCK:
|
|
case MMC_CMD_READ_MULTIPLE_BLOCK:
|
|
case MMC_CMD_WRITE_SINGLE_BLOCK:
|
|
case MMC_CMD_WRITE_MULTIPLE_BLOCK:
|
|
break;
|
|
default:
|
|
resp = &resp8;
|
|
resp_size = sizeof(resp8);
|
|
resp_match = true;
|
|
resp_match_value = R1_SPI_IDLE;
|
|
break;
|
|
};
|
|
|
|
ret = mmc_spi_sendcmd(dev, cmd->cmdidx, cmd->cmdarg, cmd->resp_type,
|
|
resp, resp_size, resp_match, resp_match_value);
|
|
if (ret)
|
|
goto done;
|
|
|
|
switch (cmd->cmdidx) {
|
|
case SD_CMD_APP_SEND_OP_COND:
|
|
case MMC_CMD_SEND_OP_COND:
|
|
cmd->response[0] = (resp8 & R1_SPI_IDLE) ? 0 : OCR_BUSY;
|
|
break;
|
|
case SD_CMD_SEND_IF_COND:
|
|
case MMC_CMD_SPI_READ_OCR:
|
|
cmd->response[0] = resp40[4];
|
|
cmd->response[0] |= (uint)resp40[3] << 8;
|
|
cmd->response[0] |= (uint)resp40[2] << 16;
|
|
cmd->response[0] |= (uint)resp40[1] << 24;
|
|
break;
|
|
case MMC_CMD_SEND_STATUS:
|
|
cmd->response[0] = (resp8 & 0xff) ?
|
|
MMC_STATUS_ERROR : MMC_STATUS_RDY_FOR_DATA;
|
|
break;
|
|
case MMC_CMD_SEND_CID:
|
|
case MMC_CMD_SEND_CSD:
|
|
ret = mmc_spi_readdata(dev, cmd->response, 1, 16);
|
|
if (ret)
|
|
return ret;
|
|
for (i = 0; i < 4; i++)
|
|
cmd->response[i] =
|
|
cpu_to_be32(cmd->response[i]);
|
|
break;
|
|
default:
|
|
cmd->response[0] = resp8;
|
|
break;
|
|
}
|
|
|
|
debug("%s: cmd%d resp0=0x%x resp1=0x%x resp2=0x%x resp3=0x%x\n",
|
|
__func__, cmd->cmdidx, cmd->response[0], cmd->response[1],
|
|
cmd->response[2], cmd->response[3]);
|
|
|
|
if (data) {
|
|
debug("%s: data flags=0x%x blocks=%d block_size=%d\n",
|
|
__func__, data->flags, data->blocks, data->blocksize);
|
|
multi = (cmd->cmdidx == MMC_CMD_WRITE_MULTIPLE_BLOCK);
|
|
if (data->flags == MMC_DATA_READ)
|
|
ret = mmc_spi_readdata(dev, data->dest,
|
|
data->blocks, data->blocksize);
|
|
else if (data->flags == MMC_DATA_WRITE)
|
|
ret = mmc_spi_writedata(dev, data->src,
|
|
data->blocks, data->blocksize,
|
|
multi);
|
|
}
|
|
|
|
done:
|
|
dm_spi_xfer(dev, 0, NULL, NULL, SPI_XFER_END);
|
|
|
|
dm_spi_release_bus(dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int mmc_spi_probe(struct udevice *dev)
|
|
{
|
|
struct mmc_spi_priv *priv = dev_get_priv(dev);
|
|
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
|
|
char *name;
|
|
|
|
priv->spi = dev_get_parent_priv(dev);
|
|
if (!priv->spi->max_hz)
|
|
priv->spi->max_hz = MMC_SPI_MAX_CLOCK;
|
|
priv->spi->speed = 0;
|
|
priv->spi->mode = SPI_MODE_0;
|
|
priv->spi->wordlen = 8;
|
|
|
|
name = malloc(strlen(dev->parent->name) + strlen(dev->name) + 4);
|
|
if (!name)
|
|
return -ENOMEM;
|
|
sprintf(name, "%s:%s", dev->parent->name, dev->name);
|
|
|
|
priv->cfg.name = name;
|
|
priv->cfg.host_caps = MMC_MODE_SPI;
|
|
priv->cfg.voltages = MMC_SPI_VOLTAGE;
|
|
priv->cfg.f_min = MMC_SPI_MIN_CLOCK;
|
|
priv->cfg.f_max = priv->spi->max_hz;
|
|
priv->cfg.part_type = PART_TYPE_DOS;
|
|
priv->cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
|
|
|
|
priv->mmc.cfg = &priv->cfg;
|
|
priv->mmc.priv = priv;
|
|
priv->mmc.dev = dev;
|
|
|
|
upriv->mmc = &priv->mmc;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mmc_spi_bind(struct udevice *dev)
|
|
{
|
|
struct mmc_spi_priv *priv = dev_get_priv(dev);
|
|
|
|
return mmc_bind(dev, &priv->mmc, &priv->cfg);
|
|
}
|
|
|
|
static const struct dm_mmc_ops mmc_spi_ops = {
|
|
.send_cmd = dm_mmc_spi_request,
|
|
.set_ios = dm_mmc_spi_set_ios,
|
|
};
|
|
|
|
static const struct udevice_id dm_mmc_spi_match[] = {
|
|
{ .compatible = "mmc-spi-slot" },
|
|
{ /* sentinel */ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(mmc_spi) = {
|
|
.name = "mmc_spi",
|
|
.id = UCLASS_MMC,
|
|
.of_match = dm_mmc_spi_match,
|
|
.ops = &mmc_spi_ops,
|
|
.probe = mmc_spi_probe,
|
|
.bind = mmc_spi_bind,
|
|
.priv_auto_alloc_size = sizeof(struct mmc_spi_priv),
|
|
};
|