mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-16 17:58:23 +00:00
ab68790798
The pins for async memory where parallel flash lives are not enabled by default, so make sure we mux them as needed. Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
164 lines
3.6 KiB
C
164 lines
3.6 KiB
C
/*
|
|
* U-boot - main board file
|
|
*
|
|
* Copyright (c) 2008-2009 Analog Devices Inc.
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <config.h>
|
|
#include <command.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <spi.h>
|
|
#include <asm/blackfin.h>
|
|
#include <asm/net.h>
|
|
#include <asm/mach-common/bits/otp.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int checkboard(void)
|
|
{
|
|
printf("Board: ADI BF518F EZ-Board board\n");
|
|
printf(" Support: http://blackfin.uclinux.org/\n");
|
|
return 0;
|
|
}
|
|
|
|
phys_size_t initdram(int board_type)
|
|
{
|
|
gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
|
|
gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
|
|
return gd->bd->bi_memsize;
|
|
}
|
|
|
|
#if defined(CONFIG_BFIN_MAC)
|
|
static void board_init_enetaddr(uchar *mac_addr)
|
|
{
|
|
bool valid_mac = false;
|
|
|
|
#if 0
|
|
/* the MAC is stored in OTP memory page 0xDF */
|
|
uint32_t ret;
|
|
uint64_t otp_mac;
|
|
|
|
ret = bfrom_OtpRead(0xDF, OTP_LOWER_HALF, &otp_mac);
|
|
if (!(ret & OTP_MASTER_ERROR)) {
|
|
uchar *otp_mac_p = (uchar *)&otp_mac;
|
|
|
|
for (ret = 0; ret < 6; ++ret)
|
|
mac_addr[ret] = otp_mac_p[5 - ret];
|
|
|
|
if (is_valid_ether_addr(mac_addr))
|
|
valid_mac = true;
|
|
}
|
|
#endif
|
|
|
|
if (!valid_mac) {
|
|
puts("Warning: Generating 'random' MAC address\n");
|
|
bfin_gen_rand_mac(mac_addr);
|
|
}
|
|
|
|
eth_setenv_enetaddr("ethaddr", mac_addr);
|
|
}
|
|
|
|
#define KSZ_MAX_HZ 5000000
|
|
|
|
#define KSZ_WRITE 0x02
|
|
#define KSZ_READ 0x03
|
|
|
|
#define KSZ_REG_STPID 0x01 /* Register 1: Chip ID1 / Start Switch */
|
|
#define KSZ_REG_GC9 0x0b /* Register 11: Global Control 9 */
|
|
#define KSZ_REG_P3C0 0x30 /* Register 48: Port 3 Control 0 */
|
|
|
|
static int ksz8893m_transfer(struct spi_slave *slave, uchar dir, uchar reg,
|
|
uchar data, uchar result[3])
|
|
{
|
|
unsigned char dout[3] = { dir, reg, data, };
|
|
return spi_xfer(slave, sizeof(dout) * 8, dout, result, SPI_XFER_BEGIN | SPI_XFER_END);
|
|
}
|
|
|
|
static int ksz8893m_reg_set(struct spi_slave *slave, uchar reg, uchar data)
|
|
{
|
|
unsigned char din[3];
|
|
return ksz8893m_transfer(slave, KSZ_WRITE, reg, data, din);
|
|
}
|
|
|
|
static int ksz8893m_reg_clear(struct spi_slave *slave, uchar reg, uchar mask)
|
|
{
|
|
int ret = 0;
|
|
unsigned char din[3];
|
|
|
|
ret |= ksz8893m_transfer(slave, KSZ_READ, reg, 0, din);
|
|
ret |= ksz8893m_reg_set(slave, reg, din[2] & mask);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ksz8893m_reset(struct spi_slave *slave)
|
|
{
|
|
int ret = 0;
|
|
|
|
/* Disable STPID mode */
|
|
ret |= ksz8893m_reg_clear(slave, KSZ_REG_GC9, 0x01);
|
|
|
|
/* Disable VLAN tag insert on Port3 */
|
|
ret |= ksz8893m_reg_clear(slave, KSZ_REG_P3C0, 0x04);
|
|
|
|
/* Start switch */
|
|
ret |= ksz8893m_reg_set(slave, KSZ_REG_STPID, 0x01);
|
|
|
|
return ret;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
static bool switch_is_alive = false;
|
|
int ret;
|
|
|
|
if (!switch_is_alive) {
|
|
struct spi_slave *slave = spi_setup_slave(0, 1, KSZ_MAX_HZ, SPI_MODE_3);
|
|
if (slave) {
|
|
if (!spi_claim_bus(slave)) {
|
|
ret = ksz8893m_reset(slave);
|
|
if (!ret)
|
|
switch_is_alive = true;
|
|
spi_release_bus(slave);
|
|
}
|
|
spi_free_slave(slave);
|
|
}
|
|
}
|
|
|
|
if (switch_is_alive)
|
|
return bfin_EMAC_initialize(bis);
|
|
else
|
|
return -1;
|
|
}
|
|
#endif
|
|
|
|
int misc_init_r(void)
|
|
{
|
|
#ifdef CONFIG_BFIN_MAC
|
|
uchar enetaddr[6];
|
|
if (!eth_getenv_enetaddr("ethaddr", enetaddr))
|
|
board_init_enetaddr(enetaddr);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
#if !defined(CONFIG_SYS_NO_FLASH)
|
|
/* setup BF518-EZBRD GPIO pin PG11 to AMS2. */
|
|
bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2);
|
|
bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG11);
|
|
|
|
# if !defined(CONFIG_BFIN_SPI)
|
|
/* setup BF518-EZBRD GPIO pin PG15 to AMS3. */
|
|
bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_7_MASK) | PORT_x_MUX_7_FUNC_3);
|
|
bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG15);
|
|
# endif
|
|
#endif
|
|
return 0;
|
|
}
|