u-boot/board/freescale/mx6qsabreauto/mx6qsabreauto.c

/*
 * Copyright (C) 2012 Freescale Semiconductor, Inc.
 *
 * Author: Fabio Estevam <fabio.estevam@freescale.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>

DECLARE_GLOBAL_DATA_PTR;

#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)

#define I2C_PAD_CTRL	(PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
	PAD_CTL_ODE | PAD_CTL_SRE_FAST)

#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)

int dram_init(void)
{
	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);

	return 0;
}

static iomux_v3_cfg_t const uart4_pads[] = {
	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};

static iomux_v3_cfg_t const enet_pads[] = {
	MX6_PAD_KEY_COL1__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_KEY_COL2__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
};

/* I2C2 PMIC, iPod, Tuner, Codec, Touch, HDMI EDID, MIPI CSI2 card */
static struct i2c_pads_info i2c_pad_info1 = {
	.scl = {
		.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
		.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
		.gp = IMX_GPIO_NR(2, 30)
	},
	.sda = {
		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
		.gp = IMX_GPIO_NR(4, 13)
	}
};

/*
 * I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor,
 * Compass Sensor, Accelerometer, Res Touch
 */
static struct i2c_pads_info i2c_pad_info2 = {
	.scl = {
		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC,
		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC,
		.gp = IMX_GPIO_NR(1, 3)
	},
	.sda = {
		.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
		.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
		.gp = IMX_GPIO_NR(3, 18)
	}
};

static iomux_v3_cfg_t const i2c3_pads[] = {
	MX6_PAD_EIM_A24__GPIO5_IO04		| MUX_PAD_CTRL(NO_PAD_CTRL),
};

static iomux_v3_cfg_t const port_exp[] = {
	MX6_PAD_SD2_DAT0__GPIO1_IO15		| MUX_PAD_CTRL(NO_PAD_CTRL),
};

static void setup_iomux_enet(void)
{
	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
}

static iomux_v3_cfg_t const usdhc3_pads[] = {
	MX6_PAD_SD3_CLK__SD3_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_CMD__SD3_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT0__SD3_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT1__SD3_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT2__SD3_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT3__SD3_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT4__SD3_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT5__SD3_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT6__SD3_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT7__SD3_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_GPIO_18__SD3_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_NANDF_CS2__GPIO6_IO15   | MUX_PAD_CTRL(NO_PAD_CTRL),
};

static void setup_iomux_uart(void)
{
	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}

#ifdef CONFIG_FSL_ESDHC
static struct fsl_esdhc_cfg usdhc_cfg[1] = {
	{USDHC3_BASE_ADDR},
};

int board_mmc_getcd(struct mmc *mmc)
{
	gpio_direction_input(IMX_GPIO_NR(6, 15));
	return !gpio_get_value(IMX_GPIO_NR(6, 15));
}

int board_mmc_init(bd_t *bis)
{
	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));

	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}
#endif

int mx6_rgmii_rework(struct phy_device *phydev)
{
	unsigned short val;

	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);

	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
	val &= 0xffe3;
	val |= 0x18;
	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);

	/* introduce tx clock delay */
	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
	val |= 0x0100;
	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);

	return 0;
}

int board_phy_config(struct phy_device *phydev)
{
	mx6_rgmii_rework(phydev);

	if (phydev->drv->config)
		phydev->drv->config(phydev);

	return 0;
}

int board_eth_init(bd_t *bis)
{
	setup_iomux_enet();

	return cpu_eth_init(bis);
}

#define BOARD_REV_B  0x200
#define BOARD_REV_A  0x100

static int mx6sabre_rev(void)
{
	/*
	 * Get Board ID information from OCOTP_GP1[15:8]
	 * i.MX6Q ARD RevA: 0x01
	 * i.MX6Q ARD RevB: 0x02
	 */
	struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
	struct fuse_bank *bank = &ocotp->bank[4];
	struct fuse_bank4_regs *fuse =
			(struct fuse_bank4_regs *)bank->fuse_regs;
	int reg = readl(&fuse->gp1);
	int ret;

	switch (reg >> 8 & 0x0F) {
	case 0x02:
		ret = BOARD_REV_B;
		break;
	case 0x01:
	default:
		ret = BOARD_REV_A;
		break;
	}

	return ret;
}

u32 get_board_rev(void)
{
	int rev = mx6sabre_rev();

	return (get_cpu_rev() & ~(0xF << 8)) | rev;
}

int board_early_init_f(void)
{
	setup_iomux_uart();

	return 0;
}

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	/* I2C 2 and 3 setup - I2C 3 hw mux with EIM */
	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
	/* I2C 3 Steer */
	gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
	imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads));
	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);

	gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
	imx_iomux_v3_setup_multiple_pads(port_exp, ARRAY_SIZE(port_exp));

	return 0;
}

#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
	/* 4 bit bus width */
	{"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
	{NULL,   0},
};
#endif

int board_late_init(void)
{
#ifdef CONFIG_CMD_BMODE
	add_board_boot_modes(board_boot_modes);
#endif

	return 0;
}

int checkboard(void)
{
	int rev = mx6sabre_rev();
	char *revname;

	switch (rev) {
	case BOARD_REV_B:
		revname = "B";
		break;
	case BOARD_REV_A:
	default:
		revname = "A";
		break;
	}

	printf("Board: MX6Q-Sabreauto rev%s\n", revname);

	return 0;
}