mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 09:30:10 +00:00
02778f2f1b
When dropping jump block support, the assumption was that all bootroms supported entry point redirection via the EVT1 register. Unfortunately, this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2 and older and BF561). No one really noticed earlier because these parts usually are booted by bypassing the bootrom entirely, and older BF533 parts are not supported at all (too many anomalies). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
113 lines
2.9 KiB
C
113 lines
2.9 KiB
C
/*
|
|
* U-boot - cpu.c CPU specific functions
|
|
*
|
|
* Copyright (c) 2005-2008 Analog Devices Inc.
|
|
*
|
|
* (C) Copyright 2000-2004
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <asm/blackfin.h>
|
|
#include <asm/cplb.h>
|
|
#include <asm/mach-common/bits/core.h>
|
|
#include <asm/mach-common/bits/ebiu.h>
|
|
#include <asm/mach-common/bits/trace.h>
|
|
|
|
#include "cpu.h"
|
|
#include "serial.h"
|
|
|
|
ulong bfin_poweron_retx;
|
|
|
|
__attribute__ ((__noreturn__))
|
|
void cpu_init_f(ulong bootflag, ulong loaded_from_ldr)
|
|
{
|
|
extern char _stext_l1;
|
|
#ifndef CONFIG_BFIN_BOOTROM_USES_EVT1
|
|
/* Build a NOP slide over the LDR jump block. Whee! */
|
|
char nops[0xC];
|
|
serial_early_puts("NOP Slide\n");
|
|
memset(nops, 0x00, sizeof(nops));
|
|
memcpy(&_stext_l1 - sizeof(nops), nops, sizeof(nops));
|
|
#endif
|
|
|
|
if (!loaded_from_ldr) {
|
|
/* Relocate sections into L1 if the LDR didn't do it -- don't
|
|
* check length because the linker script does the size
|
|
* checking at build time.
|
|
*/
|
|
serial_early_puts("L1 Relocate\n");
|
|
extern char _stext_l1, _etext_l1, _stext_l1_lma;
|
|
memcpy(&_stext_l1, &_stext_l1_lma, (&_etext_l1 - &_stext_l1));
|
|
extern char _sdata_l1, _edata_l1, _sdata_l1_lma;
|
|
memcpy(&_sdata_l1, &_sdata_l1_lma, (&_edata_l1 - &_sdata_l1));
|
|
}
|
|
#if defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__)
|
|
/* The BF537 bootrom will reset the EBIU_AMGCTL register on us
|
|
* after it has finished loading the LDR. So configure it again.
|
|
*/
|
|
else
|
|
bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL);
|
|
#endif
|
|
|
|
/* Save RETX so we can pass it while booting Linux */
|
|
bfin_poweron_retx = bootflag;
|
|
|
|
#ifdef CONFIG_DEBUG_DUMP
|
|
/* Turn on hardware trace buffer */
|
|
bfin_write_TBUFCTL(TBUFPWR | TBUFEN);
|
|
#endif
|
|
|
|
#ifndef CONFIG_PANIC_HANG
|
|
/* Reset upon a double exception rather than just hanging.
|
|
* Do not do bfin_read on SWRST as that will reset status bits.
|
|
*/
|
|
bfin_write_SWRST(DOUBLE_FAULT);
|
|
#endif
|
|
|
|
serial_early_puts("Board init flash\n");
|
|
board_init_f(bootflag);
|
|
}
|
|
|
|
int exception_init(void)
|
|
{
|
|
bfin_write_EVT3(trap);
|
|
return 0;
|
|
}
|
|
|
|
int irq_init(void)
|
|
{
|
|
#ifdef SIC_IMASK0
|
|
bfin_write_SIC_IMASK0(0);
|
|
bfin_write_SIC_IMASK1(0);
|
|
# ifdef SIC_IMASK2
|
|
bfin_write_SIC_IMASK2(0);
|
|
# endif
|
|
#elif defined(SICA_IMASK0)
|
|
bfin_write_SICA_IMASK0(0);
|
|
bfin_write_SICA_IMASK1(0);
|
|
#else
|
|
bfin_write_SIC_IMASK(0);
|
|
#endif
|
|
bfin_write_EVT2(evt_default); /* NMI */
|
|
bfin_write_EVT5(evt_default); /* hardware error */
|
|
bfin_write_EVT6(evt_default); /* core timer */
|
|
bfin_write_EVT7(evt_default);
|
|
bfin_write_EVT8(evt_default);
|
|
bfin_write_EVT9(evt_default);
|
|
bfin_write_EVT10(evt_default);
|
|
bfin_write_EVT11(evt_default);
|
|
bfin_write_EVT12(evt_default);
|
|
bfin_write_EVT13(evt_default);
|
|
bfin_write_EVT14(evt_default);
|
|
bfin_write_EVT15(evt_default);
|
|
bfin_write_ILAT(0);
|
|
CSYNC();
|
|
/* enable hardware error irq */
|
|
irq_flags = 0x3f;
|
|
local_irq_enable();
|
|
return 0;
|
|
}
|