u-boot/board/alliedtelesis/x530/x530.c
Rasmus Villemoes 1c5aedcd9a board: x530: switch to wdt_stop_all()
Since the gd->watchdog_dev member is going away, switch to using the
new wdt_stop_all() helper.

While here, clean up the preprocessor conditional: The ->watchdog_dev
member is actually guarded by CONFIG_WDT [disabling that in
x530_defconfig while keeping CONFIG_WATCHDOG breaks the build], and in
the new world order so is the existence of the wdt_stop_all()
function.

Actually, existence of wdt_stop_all() depends on CONFIG_${SPL_}WDT, so
really spell the condition using CONFIG_IS_ENABLED, and make it a C
rather than cpp if.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2021-08-31 12:04:03 +02:00

183 lines
4.5 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017 Allied Telesis Labs
*/
#include <common.h>
#include <command.h>
#include <dm.h>
#include <env.h>
#include <i2c.h>
#include <init.h>
#include <wdt.h>
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <linux/bitops.h>
#include <linux/mbus.h>
#include <linux/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include "../common/gpio_hog.h"
#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
#include <../serdes/a38x/high_speed_env_spec.h>
DECLARE_GLOBAL_DATA_PTR;
#define MVEBU_DEV_BUS_BASE (MVEBU_REGISTER(0x10400))
#define CONFIG_NVS_LOCATION 0xf4800000
#define CONFIG_NVS_SIZE (512 << 10)
static struct serdes_map board_serdes_map[] = {
{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
};
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
{
*serdes_map_array = board_serdes_map;
*count = ARRAY_SIZE(board_serdes_map);
return 0;
}
/*
* Define the DDR layout / topology here in the board file. This will
* be used by the DDR3 init code in the SPL U-Boot version to configure
* the DDR3 controller.
*/
static struct mv_ddr_topology_map board_topology_map = {
DEBUG_LEVEL_ERROR,
0x1, /* active interfaces */
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
{ { { {0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0} },
SPEED_BIN_DDR_1866M, /* speed_bin */
MV_DDR_DEV_WIDTH_16BIT, /* sdram device width */
MV_DDR_DIE_CAP_4GBIT, /* die capacity */
MV_DDR_FREQ_SAR, /* frequency */
0, 0, /* cas_l cas_wl */
MV_DDR_TEMP_LOW, /* temperature */
MV_DDR_TIM_2T} }, /* timing */
BUS_MASK_32BIT_ECC, /* subphys mask */
MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
NOT_COMBINED, /* ddr twin-die combined */
{ {0} }, /* raw spd data */
{0}, /* timing parameters */
{ {0} }, /* electrical configuration */
{0}, /* electrical parameters */
0, /* Clock enable mask */
160 /* Clock delay */
};
struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
{
/* Return the board topology as defined in the board code */
return &board_topology_map;
}
int board_early_init_f(void)
{
/* Configure MPP */
writel(0x00001111, MVEBU_MPP_BASE + 0x00);
writel(0x00000000, MVEBU_MPP_BASE + 0x04);
writel(0x55000000, MVEBU_MPP_BASE + 0x08);
writel(0x55550550, MVEBU_MPP_BASE + 0x0c);
writel(0x55555555, MVEBU_MPP_BASE + 0x10);
writel(0x00100565, MVEBU_MPP_BASE + 0x14);
writel(0x40000000, MVEBU_MPP_BASE + 0x18);
writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
return 0;
}
void spl_board_init(void)
{
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
/* window for NVS */
mbus_dt_setup_win(&mbus_state, CONFIG_NVS_LOCATION, CONFIG_NVS_SIZE,
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
/* DEV_READYn is not needed for NVS, ignore it when accessing CS1 */
writel(0x00004001, MVEBU_DEV_BUS_BASE + 0xc8);
spl_board_init();
return 0;
}
void arch_preboot_os(void)
{
if (CONFIG_IS_ENABLED(WDT))
wdt_stop_all();
}
static int led_7seg_init(unsigned int segments)
{
int node;
int ret;
int i;
struct gpio_desc desc[8];
node = fdt_node_offset_by_compatible(gd->fdt_blob, 0,
"atl,of-led-7seg");
if (node < 0)
return -ENODEV;
ret = gpio_request_list_by_name_nodev(offset_to_ofnode(node),
"segment-gpios", desc,
ARRAY_SIZE(desc), GPIOD_IS_OUT);
if (ret < 0)
return ret;
for (i = 0; i < ARRAY_SIZE(desc); i++) {
ret = dm_gpio_set_value(&desc[i], !(segments & BIT(i)));
if (ret)
return ret;
}
return 0;
}
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
static struct gpio_desc usb_en = {}, nand_wp = {}, phy_reset[2] = {},
led_en = {};
gpio_hog(&usb_en, "atl,usb-enable", "enable-gpio", 1);
gpio_hog(&nand_wp, "atl,nand-protect", "protect-gpio", 1);
gpio_hog_list(phy_reset, ARRAY_SIZE(phy_reset), "atl,phy-reset", "reset-gpio", 0);
gpio_hog(&led_en, "atl,led-enable", "enable-gpio", 1);
#ifdef MTDPARTS_MTDOOPS
env_set("mtdoops", MTDPARTS_MTDOOPS);
#endif
led_7seg_init(0xff);
return 0;
}
#endif
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
puts("Board: " CONFIG_SYS_BOARD "\n");
return 0;
}
#endif