u-boot/include/configs/goflexhome.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

90 lines
2.3 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2013 Suriyan Ramasami <suriyan.r@gmail.com>
*
* Based on dockstar.h originally written by
* Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
*
* Based on sheevaplug.h originally written by
* Prafulla Wadaskar <prafulla@marvell.com>
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
*/
#ifndef _CONFIG_GOFLEXHOME_H
#define _CONFIG_GOFLEXHOME_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
* Default GPIO configuration and LED status
*/
#define GOFLEXHOME_OE_LOW (~(0))
#define GOFLEXHOME_OE_HIGH (~(0))
#define GOFLEXHOME_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
#define GOFLEXHOME_OE_VAL_HIGH (1 << 17) /* LED pin high */
/* PHY related */
#define MV88E1116_LED_FCTRL_REG 10
#define MV88E1116_CPRSP_CR3_REG 21
#define MV88E1116_MAC_CTRL_REG 21
#define MV88E1116_PGADR_REG 22
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
/*
* Commands configuration
*/
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/*
* Environment variables configurations
*/
/*
* max 4k env size is enough, but in case of nand
* it has to be rounded to sector size
*/
/*
* Default environment variables
*/
#define CONFIG_BOOTCOMMAND \
"setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
"ubi part root; " \
"ubifsmount ubi:root; " \
"ubifsload 0x800000 ${kernel}; " \
"bootm 0x800000"
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=console=ttyS0,115200\0" \
"mtdids=nand0=orion_nand\0" \
"mtdparts="CONFIG_MTDPARTS_DEFAULT \
"kernel=/boot/uImage\0" \
"bootargs_root=ubi.mtd=root root=ubi0:root rootfstype=ubifs ro\0"
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 0
#endif /* CONFIG_CMD_NET */
/*
* * SATA Driver configuration
* */
#ifdef CONFIG_MVSATA_IDE
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#endif /*CONFIG_MVSATA_IDE*/
#endif /* _CONFIG_GOFLEXHOME_H */