u-boot/include/configs/poplar.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

62 lines
1.5 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2017 Linaro
*
* Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
*
* Configuration for Poplar 96boards CE. Parts were derived from other ARM
* configurations.
*/
#ifndef _POPLAR_H_
#define _POPLAR_H_
#include <linux/sizes.h>
/* DRAM banks */
/* SYS */
#define CONFIG_SYS_BOOTM_LEN SZ_64M
#define CONFIG_SYS_INIT_SP_ADDR 0x200000
#define CONFIG_SYS_LOAD_ADDR 0x800000
#define CONFIG_SYS_MALLOC_LEN SZ_32M
/* ATF bl33.bin load address (must match) */
/* USB configuration */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*****************************************************************************
* Initial environment variables
*****************************************************************************/
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 0) \
func(DHCP, dhcp, na)
#ifndef CONFIG_SPL_BUILD
#include <config_distro_bootcmd.h>
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"loader_mmc_blknum=0x0\0" \
"loader_mmc_nblks=0x780\0" \
"env_mmc_blknum=0xf80\0" \
"env_mmc_nblks=0x80\0" \
"kernel_addr_r=0x30000000\0" \
"pxefile_addr_r=0x32000000\0" \
"scriptaddr=0x32000000\0" \
"fdt_addr_r=0x32200000\0" \
"fdtfile=hisilicon/hi3798cv200-poplar.dtb\0" \
"ramdisk_addr_r=0x32400000\0" \
BOOTENV
/* Command line configuration */
#define CONFIG_SYS_MMC_ENV_DEV 0
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_MAXARGS 64
#endif /* _POPLAR_H_ */