u-boot/include/configs/db-88f6820-amc.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

79 lines
1.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*/
#ifndef _CONFIG_DB_88F6820_AMC_H
#define _CONFIG_DB_88F6820_AMC_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_SYS_TCLK 200000000 /* 200MHz */
/*
* Commands configuration
*/
/* USB/EHCI configuration */
#define CONFIG_EHCI_IS_TDI
/* Environment in SPI NOR flash */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI_SCAN_SHOW
#endif
/* NAND */
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* Keep device tree and initrd in lower memory so the kernel can access them */
#define CONFIG_EXTRA_ENV_SETTINGS \
"fdt_high=0x10000000\0" \
"initrd_high=0x10000000\0"
/* SPL */
/*
* Select the boot device here
*
* Currently supported are:
* SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
*
* MMC is not populated on this board.
* NAND support may be added in the future.
*/
#define SPL_BOOT_SPI_NOR_FLASH 1
#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH
/* Defines for SPL */
#define CONFIG_SPL_SIZE (140 << 10)
#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
/* SPL related SPI defines */
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
#endif
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
#undef CONFIG_SYS_MAXARGS
#define CONFIG_SYS_MAXARGS 96
#endif /* _CONFIG_DB_88F6820_AMC_H */