mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-27 13:33:40 +00:00
4bbd464268
The PHY LED mode register mask should be 0xc000 , not 0xc0000. Correct the mask to operate on the right bits. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
140 lines
2.9 KiB
C
140 lines
2.9 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* board/renesas/stout/stout.c
|
|
* This file is Stout board support.
|
|
*
|
|
* Copyright (C) 2015 Renesas Electronics Europe GmbH
|
|
* Copyright (C) 2015 Renesas Electronics Corporation
|
|
* Copyright (C) 2015 Cogent Embedded, Inc.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <netdev.h>
|
|
#include <dm.h>
|
|
#include <dm/platform_data/serial_sh.h>
|
|
#include <environment.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/io.h>
|
|
#include <linux/errno.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/arch/rmobile.h>
|
|
#include <asm/arch/rcar-mstp.h>
|
|
#include <asm/arch/mmc.h>
|
|
#include <asm/arch/sh_sdhi.h>
|
|
#include <miiphy.h>
|
|
#include <i2c.h>
|
|
#include <mmc.h>
|
|
#include "qos.h"
|
|
#include "cpld.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define CLK2MHZ(clk) (clk / 1000 / 1000)
|
|
void s_init(void)
|
|
{
|
|
struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
|
|
struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
|
|
|
|
/* Watchdog init */
|
|
writel(0xA5A5A500, &rwdt->rwtcsra);
|
|
writel(0xA5A5A500, &swdt->swtcsra);
|
|
|
|
/* CPU frequency setting. Set to 1.4GHz */
|
|
if (rmobile_get_cpu_rev_integer() >= R8A7790_CUT_ES2X) {
|
|
u32 stat = 0;
|
|
u32 stc = ((1400 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1)
|
|
<< PLL0_STC_BIT;
|
|
clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc);
|
|
|
|
do {
|
|
stat = readl(PLLECR) & PLL0ST;
|
|
} while (stat == 0x0);
|
|
}
|
|
|
|
/* QoS(Quality-of-Service) Init */
|
|
qos_init();
|
|
}
|
|
|
|
#define TMU0_MSTP125 BIT(25)
|
|
|
|
#define SD2CKCR 0xE6150078
|
|
#define SD2_97500KHZ 0x7
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* TMU0 */
|
|
mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
|
|
|
|
/*
|
|
* SD0 clock is set to 97.5MHz by default.
|
|
* Set SD2 to the 97.5MHz as well.
|
|
*/
|
|
writel(SD2_97500KHZ, SD2CKCR);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define ETHERNET_PHY_RESET 123 /* GPIO 3 31 */
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
cpld_init();
|
|
|
|
/* Force ethernet PHY out of reset */
|
|
gpio_request(ETHERNET_PHY_RESET, "phy_reset");
|
|
gpio_direction_output(ETHERNET_PHY_RESET, 0);
|
|
mdelay(20);
|
|
gpio_direction_output(ETHERNET_PHY_RESET, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
if (fdtdec_setup_mem_size_base() != 0)
|
|
return -EINVAL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init_banksize(void)
|
|
{
|
|
fdtdec_setup_memory_banksize();
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Stout has KSZ8041NL/RNL */
|
|
#define PHY_CONTROL1 0x1E
|
|
#define PHY_LED_MODE 0xC000
|
|
#define PHY_LED_MODE_ACK 0x4000
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
|
|
ret &= ~PHY_LED_MODE;
|
|
ret |= PHY_LED_MODE_ACK;
|
|
ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
|
|
|
|
return 0;
|
|
}
|
|
|
|
enum env_location env_get_location(enum env_operation op, int prio)
|
|
{
|
|
const u32 load_magic = 0xb33fc0de;
|
|
|
|
/* Block environment access if loaded using JTAG */
|
|
if ((readl(CONFIG_SPL_TEXT_BASE + 0x24) == load_magic) &&
|
|
(op != ENVOP_INIT))
|
|
return ENVL_UNKNOWN;
|
|
|
|
if (prio)
|
|
return ENVL_UNKNOWN;
|
|
|
|
return ENVL_SPI_FLASH;
|
|
}
|