u-boot/board/freescale/common/vid.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

839 lines
21 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2014 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <command.h>
#include <i2c.h>
#include <asm/io.h>
#ifdef CONFIG_FSL_LSCH2
#include <asm/arch/immap_lsch2.h>
#elif defined(CONFIG_FSL_LSCH3)
#include <asm/arch/immap_lsch3.h>
#else
#include <asm/immap_85xx.h>
#endif
#include "vid.h"
int __weak i2c_multiplexer_select_vid_channel(u8 channel)
{
return 0;
}
/*
* Compensate for a board specific voltage drop between regulator and SoC
* return a value in mV
*/
int __weak board_vdd_drop_compensation(void)
{
return 0;
}
/*
* Board specific settings for specific voltage value
*/
int __weak board_adjust_vdd(int vdd)
{
return 0;
}
#if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \
defined(CONFIG_VOL_MONITOR_IR36021_READ)
/*
* Get the i2c address configuration for the IR regulator chip
*
* There are some variance in the RDB HW regarding the I2C address configuration
* for the IR regulator chip, which is likely a problem of external resistor
* accuracy. So we just check each address in a hopefully non-intrusive mode
* and use the first one that seems to work
*
* The IR chip can show up under the following addresses:
* 0x08 (Verified on T1040RDB-PA,T4240RDB-PB,X-T4240RDB-16GPA)
* 0x09 (Verified on T1040RDB-PA)
* 0x38 (Verified on T2080QDS, T2081QDS, T4240RDB)
*/
static int find_ir_chip_on_i2c(void)
{
int i2caddress;
int ret;
u8 byte;
int i;
const int ir_i2c_addr[] = {0x38, 0x08, 0x09};
/* Check all the address */
for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) {
i2caddress = ir_i2c_addr[i];
ret = i2c_read(i2caddress,
IR36021_MFR_ID_OFFSET, 1, (void *)&byte,
sizeof(byte));
if ((ret >= 0) && (byte == IR36021_MFR_ID))
return i2caddress;
}
return -1;
}
#endif
/* Maximum loop count waiting for new voltage to take effect */
#define MAX_LOOP_WAIT_NEW_VOL 100
/* Maximum loop count waiting for the voltage to be stable */
#define MAX_LOOP_WAIT_VOL_STABLE 100
/*
* read_voltage from sensor on I2C bus
* We use average of 4 readings, waiting for WAIT_FOR_ADC before
* another reading
*/
#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */
/* If an INA220 chip is available, we can use it to read back the voltage
* as it may have a higher accuracy than the IR chip for the same purpose
*/
#ifdef CONFIG_VOL_MONITOR_INA220
#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */
#define ADC_MIN_ACCURACY 4
#else
#define WAIT_FOR_ADC 138 /* wait for 138 microseconds for ADC */
#define ADC_MIN_ACCURACY 4
#endif
#ifdef CONFIG_VOL_MONITOR_INA220
static int read_voltage_from_INA220(int i2caddress)
{
int i, ret, voltage_read = 0;
u16 vol_mon;
u8 buf[2];
for (i = 0; i < NUM_READINGS; i++) {
ret = i2c_read(I2C_VOL_MONITOR_ADDR,
I2C_VOL_MONITOR_BUS_V_OFFSET, 1,
(void *)&buf, 2);
if (ret) {
printf("VID: failed to read core voltage\n");
return ret;
}
vol_mon = (buf[0] << 8) | buf[1];
if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) {
printf("VID: Core voltage sensor error\n");
return -1;
}
debug("VID: bus voltage reads 0x%04x\n", vol_mon);
/* LSB = 4mv */
voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4;
udelay(WAIT_FOR_ADC);
}
/* calculate the average */
voltage_read /= NUM_READINGS;
return voltage_read;
}
#endif
/* read voltage from IR */
#ifdef CONFIG_VOL_MONITOR_IR36021_READ
static int read_voltage_from_IR(int i2caddress)
{
int i, ret, voltage_read = 0;
u16 vol_mon;
u8 buf;
for (i = 0; i < NUM_READINGS; i++) {
ret = i2c_read(i2caddress,
IR36021_LOOP1_VOUT_OFFSET,
1, (void *)&buf, 1);
if (ret) {
printf("VID: failed to read vcpu\n");
return ret;
}
vol_mon = buf;
if (!vol_mon) {
printf("VID: Core voltage sensor error\n");
return -1;
}
debug("VID: bus voltage reads 0x%02x\n", vol_mon);
/* Resolution is 1/128V. We scale up here to get 1/128mV
* and divide at the end
*/
voltage_read += vol_mon * 1000;
udelay(WAIT_FOR_ADC);
}
/* Scale down to the real mV as IR resolution is 1/128V, rounding up */
voltage_read = DIV_ROUND_UP(voltage_read, 128);
/* calculate the average */
voltage_read /= NUM_READINGS;
/* Compensate for a board specific voltage drop between regulator and
* SoC before converting into an IR VID value
*/
voltage_read -= board_vdd_drop_compensation();
return voltage_read;
}
#endif
#ifdef CONFIG_VOL_MONITOR_LTC3882_READ
/* read the current value of the LTC Regulator Voltage */
static int read_voltage_from_LTC(int i2caddress)
{
int ret, vcode = 0;
u8 chan = PWM_CHANNEL0;
/* select the PAGE 0 using PMBus commands PAGE for VDD*/
ret = i2c_write(I2C_VOL_MONITOR_ADDR,
PMBUS_CMD_PAGE, 1, &chan, 1);
if (ret) {
printf("VID: failed to select VDD Page 0\n");
return ret;
}
/*read the output voltage using PMBus command READ_VOUT*/
ret = i2c_read(I2C_VOL_MONITOR_ADDR,
PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2);
if (ret) {
printf("VID: failed to read the volatge\n");
return ret;
}
/* Scale down to the real mV as LTC resolution is 1/4096V,rounding up */
vcode = DIV_ROUND_UP(vcode * 1000, 4096);
return vcode;
}
#endif
static int read_voltage(int i2caddress)
{
int voltage_read;
#ifdef CONFIG_VOL_MONITOR_INA220
voltage_read = read_voltage_from_INA220(i2caddress);
#elif defined CONFIG_VOL_MONITOR_IR36021_READ
voltage_read = read_voltage_from_IR(i2caddress);
#elif defined CONFIG_VOL_MONITOR_LTC3882_READ
voltage_read = read_voltage_from_LTC(i2caddress);
#else
return -1;
#endif
return voltage_read;
}
#ifdef CONFIG_VOL_MONITOR_IR36021_SET
/*
* We need to calculate how long before the voltage stops to drop
* or increase. It returns with the loop count. Each loop takes
* several readings (WAIT_FOR_ADC)
*/
static int wait_for_new_voltage(int vdd, int i2caddress)
{
int timeout, vdd_current;
vdd_current = read_voltage(i2caddress);
/* wait until voltage starts to reach the target. Voltage slew
* rates by typical regulators will always lead to stable readings
* within each fairly long ADC interval in comparison to the
* intended voltage delta change until the target voltage is
* reached. The fairly small voltage delta change to any target
* VID voltage also means that this function will always complete
* within few iterations. If the timeout was ever reached, it would
* point to a serious failure in the regulator system.
*/
for (timeout = 0;
abs(vdd - vdd_current) > (IR_VDD_STEP_UP + IR_VDD_STEP_DOWN) &&
timeout < MAX_LOOP_WAIT_NEW_VOL; timeout++) {
vdd_current = read_voltage(i2caddress);
}
if (timeout >= MAX_LOOP_WAIT_NEW_VOL) {
printf("VID: Voltage adjustment timeout\n");
return -1;
}
return timeout;
}
/*
* this function keeps reading the voltage until it is stable or until the
* timeout expires
*/
static int wait_for_voltage_stable(int i2caddress)
{
int timeout, vdd_current, vdd;
vdd = read_voltage(i2caddress);
udelay(NUM_READINGS * WAIT_FOR_ADC);
/* wait until voltage is stable */
vdd_current = read_voltage(i2caddress);
/* The maximum timeout is
* MAX_LOOP_WAIT_VOL_STABLE * NUM_READINGS * WAIT_FOR_ADC
*/
for (timeout = MAX_LOOP_WAIT_VOL_STABLE;
abs(vdd - vdd_current) > ADC_MIN_ACCURACY &&
timeout > 0; timeout--) {
vdd = vdd_current;
udelay(NUM_READINGS * WAIT_FOR_ADC);
vdd_current = read_voltage(i2caddress);
}
if (timeout == 0)
return -1;
return vdd_current;
}
/* Set the voltage to the IR chip */
static int set_voltage_to_IR(int i2caddress, int vdd)
{
int wait, vdd_last;
int ret;
u8 vid;
/* Compensate for a board specific voltage drop between regulator and
* SoC before converting into an IR VID value
*/
vdd += board_vdd_drop_compensation();
#ifdef CONFIG_FSL_LSCH2
vid = DIV_ROUND_UP(vdd - 265, 5);
#else
vid = DIV_ROUND_UP(vdd - 245, 5);
#endif
ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET,
1, (void *)&vid, sizeof(vid));
if (ret) {
printf("VID: failed to write VID\n");
return -1;
}
wait = wait_for_new_voltage(vdd, i2caddress);
if (wait < 0)
return -1;
debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC);
vdd_last = wait_for_voltage_stable(i2caddress);
if (vdd_last < 0)
return -1;
debug("VID: Current voltage is %d mV\n", vdd_last);
return vdd_last;
}
#endif
#ifdef CONFIG_VOL_MONITOR_LTC3882_SET
/* this function sets the VDD and returns the value set */
static int set_voltage_to_LTC(int i2caddress, int vdd)
{
int ret, vdd_last, vdd_target = vdd;
/* Scale up to the LTC resolution is 1/4096V */
vdd = (vdd * 4096) / 1000;
/* 5-byte buffer which needs to be sent following the
* PMBus command PAGE_PLUS_WRITE.
*/
u8 buff[5] = {0x04, PWM_CHANNEL0, PMBUS_CMD_VOUT_COMMAND,
vdd & 0xFF, (vdd & 0xFF00) >> 8};
/* Write the desired voltage code to the regulator */
ret = i2c_write(I2C_VOL_MONITOR_ADDR,
PMBUS_CMD_PAGE_PLUS_WRITE, 1, (void *)&buff, 5);
if (ret) {
printf("VID: I2C failed to write to the volatge regulator\n");
return -1;
}
/* Wait for the volatge to get to the desired value */
do {
vdd_last = read_voltage_from_LTC(i2caddress);
if (vdd_last < 0) {
printf("VID: Couldn't read sensor abort VID adjust\n");
return -1;
}
} while (vdd_last != vdd_target);
return vdd_last;
}
#endif
static int set_voltage(int i2caddress, int vdd)
{
int vdd_last = -1;
#ifdef CONFIG_VOL_MONITOR_IR36021_SET
vdd_last = set_voltage_to_IR(i2caddress, vdd);
#elif defined CONFIG_VOL_MONITOR_LTC3882_SET
vdd_last = set_voltage_to_LTC(i2caddress, vdd);
#else
#error Specific voltage monitor must be defined
#endif
return vdd_last;
}
#ifdef CONFIG_FSL_LSCH3
int adjust_vdd(ulong vdd_override)
{
int re_enable = disable_interrupts();
struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
u32 fusesr;
#if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \
defined(CONFIG_VOL_MONITOR_IR36021_READ)
u8 vid, buf;
#else
u8 vid;
#endif
int vdd_target, vdd_current, vdd_last;
int ret, i2caddress;
unsigned long vdd_string_override;
char *vdd_string;
#ifdef CONFIG_ARCH_LS1088A
static const uint16_t vdd[32] = {
10250,
9875,
9750,
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
9000,
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
10000, /* 1.0000V */
10125,
10250,
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
};
#else
static const uint16_t vdd[32] = {
10500,
0, /* reserved */
9750,
0, /* reserved */
9500,
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
10000, /* 1.0000V */
0, /* reserved */
10250,
0, /* reserved */
10500,
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
0, /* reserved */
};
#endif
struct vdd_drive {
u8 vid;
unsigned voltage;
};
ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR);
if (ret) {
debug("VID: I2C failed to switch channel\n");
ret = -1;
goto exit;
}
#if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \
defined(CONFIG_VOL_MONITOR_IR36021_READ)
ret = find_ir_chip_on_i2c();
if (ret < 0) {
printf("VID: Could not find voltage regulator on I2C.\n");
ret = -1;
goto exit;
} else {
i2caddress = ret;
debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
}
/* check IR chip work on Intel mode*/
ret = i2c_read(i2caddress,
IR36021_INTEL_MODE_OOFSET,
1, (void *)&buf, 1);
if (ret) {
printf("VID: failed to read IR chip mode.\n");
ret = -1;
goto exit;
}
if ((buf & IR36021_MODE_MASK) != IR36021_INTEL_MODE) {
printf("VID: IR Chip is not used in Intel mode.\n");
ret = -1;
goto exit;
}
#endif
/* get the voltage ID from fuse status register */
fusesr = in_le32(&gur->dcfg_fusesr);
vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) &
FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK;
if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) {
vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) &
FSL_CHASSIS3_DCFG_FUSESR_VID_MASK;
}
vdd_target = vdd[vid];
/* check override variable for overriding VDD */
vdd_string = env_get(CONFIG_VID_FLS_ENV);
if (vdd_override == 0 && vdd_string &&
!strict_strtoul(vdd_string, 10, &vdd_string_override))
vdd_override = vdd_string_override;
if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) {
vdd_target = vdd_override * 10; /* convert to 1/10 mV */
debug("VDD override is %lu\n", vdd_override);
} else if (vdd_override != 0) {
printf("Invalid value.\n");
}
/* divide and round up by 10 to get a value in mV */
vdd_target = DIV_ROUND_UP(vdd_target, 10);
if (vdd_target == 0) {
debug("VID: VID not used\n");
ret = 0;
goto exit;
} else if (vdd_target < VDD_MV_MIN || vdd_target > VDD_MV_MAX) {
/* Check vdd_target is in valid range */
printf("VID: Target VID %d mV is not in range.\n",
vdd_target);
ret = -1;
goto exit;
} else {
debug("VID: vid = %d mV\n", vdd_target);
}
/*
* Read voltage monitor to check real voltage.
*/
vdd_last = read_voltage(i2caddress);
if (vdd_last < 0) {
printf("VID: Couldn't read sensor abort VID adjustment\n");
ret = -1;
goto exit;
}
vdd_current = vdd_last;
debug("VID: Core voltage is currently at %d mV\n", vdd_last);
#ifdef CONFIG_VOL_MONITOR_LTC3882_SET
/* Set the target voltage */
vdd_last = vdd_current = set_voltage(i2caddress, vdd_target);
#else
/*
* Adjust voltage to at or one step above target.
* As measurements are less precise than setting the values
* we may run through dummy steps that cancel each other
* when stepping up and then down.
*/
while (vdd_last > 0 &&
vdd_last < vdd_target) {
vdd_current += IR_VDD_STEP_UP;
vdd_last = set_voltage(i2caddress, vdd_current);
}
while (vdd_last > 0 &&
vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) {
vdd_current -= IR_VDD_STEP_DOWN;
vdd_last = set_voltage(i2caddress, vdd_current);
}
#endif
if (board_adjust_vdd(vdd_target) < 0) {
ret = -1;
goto exit;
}
if (vdd_last > 0)
printf("VID: Core voltage after adjustment is at %d mV\n",
vdd_last);
else
ret = -1;
exit:
if (re_enable)
enable_interrupts();
i2c_multiplexer_select_vid_channel(I2C_MUX_CH_DEFAULT);
return ret;
}
#else /* !CONFIG_FSL_LSCH3 */
int adjust_vdd(ulong vdd_override)
{
int re_enable = disable_interrupts();
#if defined(CONFIG_FSL_LSCH2)
struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
#else
ccsr_gur_t __iomem *gur =
(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
#endif
u32 fusesr;
u8 vid, buf;
int vdd_target, vdd_current, vdd_last;
int ret, i2caddress;
unsigned long vdd_string_override;
char *vdd_string;
static const uint16_t vdd[32] = {
0, /* unused */
9875, /* 0.9875V */
9750,
9625,
9500,
9375,
9250,
9125,
9000,
8875,
8750,
8625,
8500,
8375,
8250,
8125,
10000, /* 1.0000V */
10125,
10250,
10375,
10500,
10625,
10750,
10875,
11000,
0, /* reserved */
};
struct vdd_drive {
u8 vid;
unsigned voltage;
};
ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR);
if (ret) {
debug("VID: I2C failed to switch channel\n");
ret = -1;
goto exit;
}
#if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \
defined(CONFIG_VOL_MONITOR_IR36021_READ)
ret = find_ir_chip_on_i2c();
if (ret < 0) {
printf("VID: Could not find voltage regulator on I2C.\n");
ret = -1;
goto exit;
} else {
i2caddress = ret;
debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
}
/* check IR chip work on Intel mode*/
ret = i2c_read(i2caddress,
IR36021_INTEL_MODE_OOFSET,
1, (void *)&buf, 1);
if (ret) {
printf("VID: failed to read IR chip mode.\n");
ret = -1;
goto exit;
}
if ((buf & IR36021_MODE_MASK) != IR36021_INTEL_MODE) {
printf("VID: IR Chip is not used in Intel mode.\n");
ret = -1;
goto exit;
}
#endif
/* get the voltage ID from fuse status register */
fusesr = in_be32(&gur->dcfg_fusesr);
/*
* VID is used according to the table below
* ---------------------------------------
* | DA_V |
* |-------------------------------------|
* | 5b00000 | 5b00001-5b11110 | 5b11111 |
* ---------------+---------+-----------------+---------|
* | D | 5b00000 | NO VID | VID = DA_V | NO VID |
* | A |----------+---------+-----------------+---------|
* | _ | 5b00001 |VID = | VID = |VID = |
* | V | ~ | DA_V_ALT| DA_V_ALT | DA_A_VLT|
* | _ | 5b11110 | | | |
* | A |----------+---------+-----------------+---------|
* | L | 5b11111 | No VID | VID = DA_V | NO VID |
* | T | | | | |
* ------------------------------------------------------
*/
#ifdef CONFIG_FSL_LSCH2
vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_ALTVID_SHIFT) &
FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK;
if ((vid == 0) || (vid == FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK)) {
vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) &
FSL_CHASSIS2_DCFG_FUSESR_VID_MASK;
}
#else
vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
if ((vid == 0) || (vid == FSL_CORENET_DCFG_FUSESR_ALTVID_MASK)) {
vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) &
FSL_CORENET_DCFG_FUSESR_VID_MASK;
}
#endif
vdd_target = vdd[vid];
/* check override variable for overriding VDD */
vdd_string = env_get(CONFIG_VID_FLS_ENV);
if (vdd_override == 0 && vdd_string &&
!strict_strtoul(vdd_string, 10, &vdd_string_override))
vdd_override = vdd_string_override;
if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) {
vdd_target = vdd_override * 10; /* convert to 1/10 mV */
debug("VDD override is %lu\n", vdd_override);
} else if (vdd_override != 0) {
printf("Invalid value.\n");
}
if (vdd_target == 0) {
debug("VID: VID not used\n");
ret = 0;
goto exit;
} else {
/* divide and round up by 10 to get a value in mV */
vdd_target = DIV_ROUND_UP(vdd_target, 10);
debug("VID: vid = %d mV\n", vdd_target);
}
/*
* Read voltage monitor to check real voltage.
*/
vdd_last = read_voltage(i2caddress);
if (vdd_last < 0) {
printf("VID: Couldn't read sensor abort VID adjustment\n");
ret = -1;
goto exit;
}
vdd_current = vdd_last;
debug("VID: Core voltage is currently at %d mV\n", vdd_last);
/*
* Adjust voltage to at or one step above target.
* As measurements are less precise than setting the values
* we may run through dummy steps that cancel each other
* when stepping up and then down.
*/
while (vdd_last > 0 &&
vdd_last < vdd_target) {
vdd_current += IR_VDD_STEP_UP;
vdd_last = set_voltage(i2caddress, vdd_current);
}
while (vdd_last > 0 &&
vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) {
vdd_current -= IR_VDD_STEP_DOWN;
vdd_last = set_voltage(i2caddress, vdd_current);
}
if (vdd_last > 0)
printf("VID: Core voltage after adjustment is at %d mV\n",
vdd_last);
else
ret = -1;
exit:
if (re_enable)
enable_interrupts();
i2c_multiplexer_select_vid_channel(I2C_MUX_CH_DEFAULT);
return ret;
}
#endif
static int print_vdd(void)
{
int vdd_last, ret, i2caddress;
ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR);
if (ret) {
debug("VID : I2c failed to switch channel\n");
return -1;
}
#if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \
defined(CONFIG_VOL_MONITOR_IR36021_READ)
ret = find_ir_chip_on_i2c();
if (ret < 0) {
printf("VID: Could not find voltage regulator on I2C.\n");
goto exit;
} else {
i2caddress = ret;
debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
}
#endif
/*
* Read voltage monitor to check real voltage.
*/
vdd_last = read_voltage(i2caddress);
if (vdd_last < 0) {
printf("VID: Couldn't read sensor abort VID adjustment\n");
goto exit;
}
printf("VID: Core voltage is at %d mV\n", vdd_last);
exit:
i2c_multiplexer_select_vid_channel(I2C_MUX_CH_DEFAULT);
return ret < 0 ? -1 : 0;
}
static int do_vdd_override(cmd_tbl_t *cmdtp,
int flag, int argc,
char * const argv[])
{
ulong override;
if (argc < 2)
return CMD_RET_USAGE;
if (!strict_strtoul(argv[1], 10, &override))
adjust_vdd(override); /* the value is checked by callee */
else
return CMD_RET_USAGE;
return 0;
}
static int do_vdd_read(cmd_tbl_t *cmdtp,
int flag, int argc,
char * const argv[])
{
if (argc < 1)
return CMD_RET_USAGE;
print_vdd();
return 0;
}
U_BOOT_CMD(
vdd_override, 2, 0, do_vdd_override,
"override VDD",
" - override with the voltage specified in mV, eg. 1050"
);
U_BOOT_CMD(
vdd_read, 1, 0, do_vdd_read,
"read VDD",
" - Read the voltage specified in mV"
)