mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-19 03:08:31 +00:00
8fe280f330
On mx6 sabreauto board, there are two USB ports: 0: OTG 1: HOST The EHCI driver is enabled for this board, but the IOMUX and VBUS power control is not implemented, which cause both USB port failed to work. This patch fix the problem by adding the board support codes. Since the power control uses the GPIO pin from port expander MAX7310, the PCA953X driver is enabled for accessing the MAX7310. The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting its daisy chain. Add a new function "imx_iomux_set_gpr_register" to handle GPR register setting. Signed-off-by: Ye.Li <B37916@freescale.com>
94 lines
2.3 KiB
C
94 lines
2.3 KiB
C
/*
|
|
* Based on the iomux-v3.c from Linux kernel:
|
|
* Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
|
|
* Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
|
|
* <armlinux@phytec.de>
|
|
*
|
|
* Copyright (C) 2004-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#if !defined(CONFIG_MX25) && !defined(CONFIG_VF610)
|
|
#include <asm/arch/sys_proto.h>
|
|
#endif
|
|
#include <asm/imx-common/iomux-v3.h>
|
|
|
|
static void *base = (void *)IOMUXC_BASE_ADDR;
|
|
|
|
/*
|
|
* configures a single pad in the iomuxer
|
|
*/
|
|
void imx_iomux_v3_setup_pad(iomux_v3_cfg_t pad)
|
|
{
|
|
u32 mux_ctrl_ofs = (pad & MUX_CTRL_OFS_MASK) >> MUX_CTRL_OFS_SHIFT;
|
|
u32 mux_mode = (pad & MUX_MODE_MASK) >> MUX_MODE_SHIFT;
|
|
u32 sel_input_ofs =
|
|
(pad & MUX_SEL_INPUT_OFS_MASK) >> MUX_SEL_INPUT_OFS_SHIFT;
|
|
u32 sel_input =
|
|
(pad & MUX_SEL_INPUT_MASK) >> MUX_SEL_INPUT_SHIFT;
|
|
u32 pad_ctrl_ofs =
|
|
(pad & MUX_PAD_CTRL_OFS_MASK) >> MUX_PAD_CTRL_OFS_SHIFT;
|
|
u32 pad_ctrl = (pad & MUX_PAD_CTRL_MASK) >> MUX_PAD_CTRL_SHIFT;
|
|
|
|
#if defined CONFIG_MX6SL
|
|
/* Check whether LVE bit needs to be set */
|
|
if (pad_ctrl & PAD_CTL_LVE) {
|
|
pad_ctrl &= ~PAD_CTL_LVE;
|
|
pad_ctrl |= PAD_CTL_LVE_BIT;
|
|
}
|
|
#endif
|
|
|
|
if (mux_ctrl_ofs)
|
|
__raw_writel(mux_mode, base + mux_ctrl_ofs);
|
|
|
|
if (sel_input_ofs)
|
|
__raw_writel(sel_input, base + sel_input_ofs);
|
|
|
|
#ifdef CONFIG_IOMUX_SHARE_CONF_REG
|
|
if (!(pad_ctrl & NO_PAD_CTRL))
|
|
__raw_writel((mux_mode << PAD_MUX_MODE_SHIFT) | pad_ctrl,
|
|
base + pad_ctrl_ofs);
|
|
#else
|
|
if (!(pad_ctrl & NO_PAD_CTRL) && pad_ctrl_ofs)
|
|
__raw_writel(pad_ctrl, base + pad_ctrl_ofs);
|
|
#endif
|
|
}
|
|
|
|
/* configures a list of pads within declared with IOMUX_PADS macro */
|
|
void imx_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t const *pad_list,
|
|
unsigned count)
|
|
{
|
|
iomux_v3_cfg_t const *p = pad_list;
|
|
int stride;
|
|
int i;
|
|
|
|
#if defined(CONFIG_MX6QDL)
|
|
stride = 2;
|
|
if (!is_cpu_type(MXC_CPU_MX6Q) && !is_cpu_type(MXC_CPU_MX6D))
|
|
p += 1;
|
|
#else
|
|
stride = 1;
|
|
#endif
|
|
for (i = 0; i < count; i++) {
|
|
imx_iomux_v3_setup_pad(*p);
|
|
p += stride;
|
|
}
|
|
}
|
|
|
|
void imx_iomux_set_gpr_register(int group, int start_bit,
|
|
int num_bits, int value)
|
|
{
|
|
int i = 0;
|
|
u32 reg;
|
|
reg = readl(base + group * 4);
|
|
while (num_bits) {
|
|
reg &= ~(1<<(start_bit + i));
|
|
i++;
|
|
num_bits--;
|
|
}
|
|
reg |= (value << start_bit);
|
|
writel(reg, base + group * 4);
|
|
}
|