mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-09-30 11:22:09 +00:00
0204d1b56b
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
44 lines
1.1 KiB
Text
44 lines
1.1 KiB
Text
if ARCH_SNAPDRAGON
|
|
|
|
config SYS_SOC
|
|
default "snapdragon"
|
|
|
|
config SYS_MALLOC_F_LEN
|
|
default 0x2000
|
|
|
|
config SPL_SYS_MALLOC_F_LEN
|
|
default 0x2000
|
|
|
|
choice
|
|
prompt "Snapdragon board select"
|
|
|
|
config TARGET_DRAGONBOARD410C
|
|
bool "96Boards Dragonboard 410C"
|
|
select BOARD_LATE_INIT
|
|
select ENABLE_ARM_SOC_BOOT0_HOOK
|
|
help
|
|
Support for 96Boards Dragonboard 410C. This board complies with
|
|
96Board Open Platform Specifications. Features:
|
|
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
|
|
- 1GiB RAM
|
|
- 8GiB eMMC, uSD slot
|
|
- WiFi, Bluetooth and GPS module
|
|
- 2x Host, 1x Device USB port
|
|
- HDMI
|
|
- 20-pin low speed and 40-pin high speed expanders, 4 LED, 3 buttons
|
|
|
|
config TARGET_DRAGONBOARD820C
|
|
bool "96Boards Dragonboard 820C"
|
|
help
|
|
Support for 96Boards Dragonboard 820C. This board complies with
|
|
96Board Open Platform Specifications. Features:
|
|
- Qualcomm Snapdragon 820C SoC - APQ8096 (4xKyro CPU)
|
|
- 3GiB RAM
|
|
- 32GiB UFS drive
|
|
|
|
endchoice
|
|
|
|
source "board/qualcomm/dragonboard410c/Kconfig"
|
|
source "board/qualcomm/dragonboard820c/Kconfig"
|
|
|
|
endif
|