u-boot/board/Marvell/mvebu_db-88f3720/board.c
Stefan Roese 01e62c7f11 arm64: mvebu: Add Armada 3700 db-88f3720 development board support
This patch adds basic support for the Marvell Armada 3700 DB-88F3720
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- Ethernet

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00

134 lines
3 KiB
C

/*
* Copyright (C) 2016 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
DECLARE_GLOBAL_DATA_PTR;
/* IO expander I2C device */
#define I2C_IO_EXP_ADDR 0x22
#define I2C_IO_CFG_REG_0 0x6
#define I2C_IO_DATA_OUT_REG_0 0x2
#define I2C_IO_REG_0_SATA_OFF 2
#define I2C_IO_REG_0_USB_H_OFF 1
int board_early_init_f(void)
{
/* Nothing to do (yet), perhaps later some pin-muxing etc */
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
return 0;
}
/* Board specific AHCI / SATA enable code */
int board_ahci_enable(void)
{
struct udevice *dev;
int ret;
u8 buf[8];
/* Configure IO exander PCA9555: 7bit address 0x22 */
ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
if (ret) {
printf("Cannot find PCA9555: %d\n", ret);
return 0;
}
ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to read IO expander value via I2C\n");
return -EIO;
}
/*
* Enable SATA power via IO expander connected via I2C by setting
* the corresponding bit to output mode to enable power for SATA
*/
buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF);
ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
return 0;
}
/* Board specific xHCI enable code */
int board_xhci_enable(void)
{
struct udevice *dev;
int ret;
u8 buf[8];
/* Configure IO exander PCA9555: 7bit address 0x22 */
ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
if (ret) {
printf("Cannot find PCA9555: %d\n", ret);
return 0;
}
printf("Enable USB VBUS\n");
/*
* Read configuration (direction) and set VBUS pin as output
* (reset pin = output)
*/
ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to read IO expander value via I2C\n");
return -EIO;
}
buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
/* Read VBUS output value and disable it */
ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
if (ret) {
printf("Failed to read IO expander value via I2C\n");
return -EIO;
}
buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
/*
* Required delay for configuration to settle - must wait for
* power on port is disabled in case VBUS signal was high,
* required 3 seconds delay to let VBUS signal fully settle down
*/
mdelay(3000);
/* Enable VBUS power: Set output value of VBUS pin as enabled */
buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF);
ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
mdelay(500); /* required delay to let output value settle */
return 0;
}