Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-17 10:18:38 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/freescale/mpc837xemds/mpc837xemds.c
Claudiu Manoil 93f26f130e net: Merge asm/fsl_enet.h into fsl_mdio.h 
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.

To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2014-09-08 10:30:33 -07:00

344 lines
8.5 KiB
C
Raw Blame History

/*
* Copyright (C) 2007,2010 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <hwconfig.h>
#include <i2c.h>
#include <asm/io.h>
#include <asm/fsl_mpc83xx_serdes.h>
#include <spd_sdram.h>
#include <tsec.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <fsl_esdhc.h>
#include <fsl_mdio.h>
#include <phy.h>
#include "pci.h"
#include "../common/pq-mds-pib.h"
int board_early_init_f(void)
{
u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
/* Enable flash write */
bcsr[0x9] &= ~0x04;
/* Clear all of the interrupt of BCSR */
bcsr[0xe] = 0xff;
#ifdef CONFIG_FSL_SERDES
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
u32 spridr = in_be32(&immr->sysconf.spridr);
/* we check only part num, and don't look for CPU revisions */
switch (PARTID_NO_E(spridr)) {
case SPR_8377:
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
break;
case SPR_8378:
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
break;
case SPR_8379:
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_SATA,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
break;
default:
printf("serdes not configured: unknown CPU part number: "
"%04x\n", spridr >> 16);
break;
}
#endif /* CONFIG_FSL_SERDES */
return 0;
}
#ifdef CONFIG_FSL_ESDHC
int board_mmc_init(bd_t *bd)
{
struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
if (!hwconfig("esdhc"))
return 0;
/* Set SPI_SD, SER_SD, and IRQ4_WP so that SD signals go through */
bcsr[0xc] |= 0x4c;
/* Set proper bits in SICR to allow SD signals through */
clrsetbits_be32(&im->sysconf.sicrl, SICRL_USB_B, SICRL_USB_B_SD);
clrsetbits_be32(&im->sysconf.sicrh, SICRH_GPIO2_E | SICRH_SPI,
SICRH_GPIO2_E_SD | SICRH_SPI_SD);
return fsl_esdhc_mmc_init(bd);
}
#endif
#if defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2)
int board_eth_init(bd_t *bd)
{
struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[2];
struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
u32 rcwh = in_be32(&im->reset.rcwh);
u32 tsec_mode;
int num = 0;
/* New line after Net: */
printf("\n");
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
printf(CONFIG_TSEC1_NAME ": ");
tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
if (tsec_mode == HRCWH_TSEC1M_IN_RGMII) {
printf("RGMII\n");
/* this is default, no need to fixup */
} else if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) {
printf("SGMII\n");
tsec_info[num].phyaddr = TSEC1_PHY_ADDR_SGMII;
tsec_info[num].flags = TSEC_GIGABIT;
} else {
printf("unsupported PHY type\n");
}
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
printf(CONFIG_TSEC2_NAME ": ");
tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
if (tsec_mode == HRCWH_TSEC2M_IN_RGMII) {
printf("RGMII\n");
/* this is default, no need to fixup */
} else if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) {
printf("SGMII\n");
tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII;
tsec_info[num].flags = TSEC_GIGABIT;
} else {
printf("unsupported PHY type\n");
}
num++;
#endif
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
mdio_info.name = DEFAULT_MII_NAME;
fsl_pq_mdio_init(bd, &mdio_info);
return tsec_eth_init(bd, tsec_info, num);
}
static void __ft_tsec_fixup(void *blob, bd_t *bd, const char *alias,
int phy_addr)
{
const u32 *ph;
int off;
int err;
off = fdt_path_offset(blob, alias);
if (off < 0) {
printf("WARNING: could not find %s alias: %s.\n", alias,
fdt_strerror(off));
return;
}
err = fdt_fixup_phy_connection(blob, off, PHY_INTERFACE_MODE_SGMII);
if (err) {
printf("WARNING: could not set phy-connection-type for %s: "
"%s.\n", alias, fdt_strerror(err));
return;
}
ph = (u32 *)fdt_getprop(blob, off, "phy-handle", 0);
if (!ph) {
printf("WARNING: could not get phy-handle for %s.\n",
alias);
return;
}
off = fdt_node_offset_by_phandle(blob, *ph);
if (off < 0) {
printf("WARNING: could not get phy node for %s: %s\n", alias,
fdt_strerror(off));
return;
}
phy_addr = cpu_to_fdt32(phy_addr);
err = fdt_setprop(blob, off, "reg", &phy_addr, sizeof(phy_addr));
if (err < 0) {
printf("WARNING: could not set phy node's reg for %s: "
"%s.\n", alias, fdt_strerror(err));
return;
}
}
static void ft_tsec_fixup(void *blob, bd_t *bd)
{
struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
u32 rcwh = in_be32(&im->reset.rcwh);
u32 tsec_mode;
#ifdef CONFIG_TSEC1
tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
if (tsec_mode == HRCWH_TSEC1M_IN_SGMII)
__ft_tsec_fixup(blob, bd, "ethernet0", TSEC1_PHY_ADDR_SGMII);
#endif
#ifdef CONFIG_TSEC2
tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
if (tsec_mode == HRCWH_TSEC2M_IN_SGMII)
__ft_tsec_fixup(blob, bd, "ethernet1", TSEC2_PHY_ADDR_SGMII);
#endif
}
#else
static inline void ft_tsec_fixup(void *blob, bd_t *bd) {}
#endif /* defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) */
int board_early_init_r(void)
{
#ifdef CONFIG_PQ_MDS_PIB
pib_init();
#endif
return 0;
}
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
int fixed_sdram(void);
phys_size_t initdram(int board_type)
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
u32 msize = 0;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
return -1;
#if defined(CONFIG_SPD_EEPROM)
msize = spd_sdram();
#else
msize = fixed_sdram();
#endif
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/* Initialize DDR ECC byte */
ddr_enable_ecc(msize * 1024 * 1024);
#endif
/* return total bus DDR size(bytes) */
return (msize * 1024 * 1024);
}
#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
************************************************************************/
int fixed_sdram(void)
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
u32 msize_log2 = __ilog2(msize);
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
#if (CONFIG_SYS_DDR_SIZE != 512)
#warning Currenly any ddr size other than 512 is not supported
#endif
im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
udelay(50000);
im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
udelay(1000);
im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
udelay(1000);
im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
__asm__ __volatile__("sync");
udelay(1000);
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
udelay(2000);
return CONFIG_SYS_DDR_SIZE;
}
#endif /*!CONFIG_SYS_SPD_EEPROM */
int checkboard(void)
{
puts("Board: Freescale MPC837xEMDS\n");
return 0;
}
#ifdef CONFIG_PCI
int board_pci_host_broken(void)
{
struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
const u32 rcw_mask = HRCWH_PCI1_ARBITER_ENABLE | HRCWH_PCI_HOST;
/* It's always OK in case of external arbiter. */
if (hwconfig_subarg_cmp("pci", "arbiter", "external"))
return 0;
if ((in_be32(&im->reset.rcwh) & rcw_mask) != rcw_mask)
return 1;
return 0;
}
static void ft_pci_fixup(void *blob, bd_t *bd)
{
const char *status = "broken (no arbiter)";
int off;
int err;
off = fdt_path_offset(blob, "pci0");
if (off < 0) {
printf("WARNING: could not find pci0 alias: %s.\n",
fdt_strerror(off));
return;
}
err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
if (err) {
printf("WARNING: could not set status for pci0: %s.\n",
fdt_strerror(err));
return;
}
}
#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
ft_tsec_fixup(blob, bd);
fdt_fixup_dr_usb(blob, bd);
fdt_fixup_esdhc(blob, bd);
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
if (board_pci_host_broken())
ft_pci_fixup(blob, bd);
ft_pcie_fixup(blob, bd);
#endif
}
#endif /* CONFIG_OF_BOARD_SETUP */
Reference in a new issue View git blame Copy permalink