u-boot/drivers/mmc/sunxi_mmc.c
Jagan Teki e8f37f4203 mmc: sunxi: Fix mmc clocks for DM_MMC
Existing clock configure code has been followed based on the
legacy MMC dt node definitions and it cannot work with recent
dts(i) sync from Linux.

So, add clock configure code for Allwinner platforms which support
DM_MMC and eventually this will drop once CLK support is in Mainline.

Fixes: 3c92cca3cd ("ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> # Gemei G9 A10 Tablet
Tested-by: Marek Kraus <gamelasterv2@gmail.com> # A10-OLinuXino-Lime
2019-01-10 14:45:15 +05:30

709 lines
17 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2011
* Allwinner Technology Co., Ltd. <www.allwinnertech.com>
* Aaron <leafy.myeh@allwinnertech.com>
*
* MMC driver for allwinner sunxi platform.
*/
#include <common.h>
#include <dm.h>
#include <errno.h>
#include <malloc.h>
#include <mmc.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/cpu.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm-generic/gpio.h>
#ifdef CONFIG_DM_MMC
struct sunxi_mmc_variant {
u16 gate_offset;
u16 mclk_offset;
};
#endif
struct sunxi_mmc_plat {
struct mmc_config cfg;
struct mmc mmc;
};
struct sunxi_mmc_priv {
unsigned mmc_no;
uint32_t *mclkreg;
unsigned fatal_err;
struct gpio_desc cd_gpio; /* Change Detect GPIO */
int cd_inverted; /* Inverted Card Detect */
struct sunxi_mmc *reg;
struct mmc_config cfg;
#ifdef CONFIG_DM_MMC
const struct sunxi_mmc_variant *variant;
#endif
};
#if !CONFIG_IS_ENABLED(DM_MMC)
/* support 4 mmc hosts */
struct sunxi_mmc_priv mmc_host[4];
static int sunxi_mmc_getcd_gpio(int sdc_no)
{
switch (sdc_no) {
case 0: return sunxi_name_to_gpio(CONFIG_MMC0_CD_PIN);
case 1: return sunxi_name_to_gpio(CONFIG_MMC1_CD_PIN);
case 2: return sunxi_name_to_gpio(CONFIG_MMC2_CD_PIN);
case 3: return sunxi_name_to_gpio(CONFIG_MMC3_CD_PIN);
}
return -EINVAL;
}
static int mmc_resource_init(int sdc_no)
{
struct sunxi_mmc_priv *priv = &mmc_host[sdc_no];
struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
int cd_pin, ret = 0;
debug("init mmc %d resource\n", sdc_no);
switch (sdc_no) {
case 0:
priv->reg = (struct sunxi_mmc *)SUNXI_MMC0_BASE;
priv->mclkreg = &ccm->sd0_clk_cfg;
break;
case 1:
priv->reg = (struct sunxi_mmc *)SUNXI_MMC1_BASE;
priv->mclkreg = &ccm->sd1_clk_cfg;
break;
case 2:
priv->reg = (struct sunxi_mmc *)SUNXI_MMC2_BASE;
priv->mclkreg = &ccm->sd2_clk_cfg;
break;
#ifdef SUNXI_MMC3_BASE
case 3:
priv->reg = (struct sunxi_mmc *)SUNXI_MMC3_BASE;
priv->mclkreg = &ccm->sd3_clk_cfg;
break;
#endif
default:
printf("Wrong mmc number %d\n", sdc_no);
return -1;
}
priv->mmc_no = sdc_no;
cd_pin = sunxi_mmc_getcd_gpio(sdc_no);
if (cd_pin >= 0) {
ret = gpio_request(cd_pin, "mmc_cd");
if (!ret) {
sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP);
ret = gpio_direction_input(cd_pin);
}
}
return ret;
}
#endif
static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
{
unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly;
bool new_mode = true;
bool calibrate = false;
u32 val = 0;
if (!IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE))
new_mode = false;
/* A83T support new mode only on eMMC */
if (IS_ENABLED(CONFIG_MACH_SUN8I_A83T) && priv->mmc_no != 2)
new_mode = false;
#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
calibrate = true;
#endif
if (hz <= 24000000) {
pll = CCM_MMC_CTRL_OSCM24;
pll_hz = 24000000;
} else {
#ifdef CONFIG_MACH_SUN9I
pll = CCM_MMC_CTRL_PLL_PERIPH0;
pll_hz = clock_get_pll4_periph0();
#elif defined(CONFIG_MACH_SUN50I_H6)
pll = CCM_MMC_CTRL_PLL6X2;
pll_hz = clock_get_pll6() * 2;
#else
pll = CCM_MMC_CTRL_PLL6;
pll_hz = clock_get_pll6();
#endif
}
div = pll_hz / hz;
if (pll_hz % hz)
div++;
n = 0;
while (div > 16) {
n++;
div = (div + 1) / 2;
}
if (n > 3) {
printf("mmc %u error cannot set clock to %u\n", priv->mmc_no,
hz);
return -1;
}
/* determine delays */
if (hz <= 400000) {
oclk_dly = 0;
sclk_dly = 0;
} else if (hz <= 25000000) {
oclk_dly = 0;
sclk_dly = 5;
#ifdef CONFIG_MACH_SUN9I
} else if (hz <= 52000000) {
oclk_dly = 5;
sclk_dly = 4;
} else {
/* hz > 52000000 */
oclk_dly = 2;
sclk_dly = 4;
#else
} else if (hz <= 52000000) {
oclk_dly = 3;
sclk_dly = 4;
} else {
/* hz > 52000000 */
oclk_dly = 1;
sclk_dly = 4;
#endif
}
if (new_mode) {
#ifdef CONFIG_MMC_SUNXI_HAS_NEW_MODE
#ifdef CONFIG_MMC_SUNXI_HAS_MODE_SWITCH
val = CCM_MMC_CTRL_MODE_SEL_NEW;
#endif
setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW);
#endif
} else if (!calibrate) {
/*
* Use hardcoded delay values if controller doesn't support
* calibration
*/
val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) |
CCM_MMC_CTRL_SCLK_DLY(sclk_dly);
}
writel(CCM_MMC_CTRL_ENABLE| pll | CCM_MMC_CTRL_N(n) |
CCM_MMC_CTRL_M(div) | val, priv->mclkreg);
debug("mmc %u set mod-clk req %u parent %u n %u m %u rate %u\n",
priv->mmc_no, hz, pll_hz, 1u << n, div, pll_hz / (1u << n) / div);
return 0;
}
static int mmc_update_clk(struct sunxi_mmc_priv *priv)
{
unsigned int cmd;
unsigned timeout_msecs = 2000;
unsigned long start = get_timer(0);
cmd = SUNXI_MMC_CMD_START |
SUNXI_MMC_CMD_UPCLK_ONLY |
SUNXI_MMC_CMD_WAIT_PRE_OVER;
writel(cmd, &priv->reg->cmd);
while (readl(&priv->reg->cmd) & SUNXI_MMC_CMD_START) {
if (get_timer(start) > timeout_msecs)
return -1;
}
/* clock update sets various irq status bits, clear these */
writel(readl(&priv->reg->rint), &priv->reg->rint);
return 0;
}
static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc)
{
unsigned rval = readl(&priv->reg->clkcr);
/* Disable Clock */
rval &= ~SUNXI_MMC_CLK_ENABLE;
writel(rval, &priv->reg->clkcr);
if (mmc_update_clk(priv))
return -1;
/* Set mod_clk to new rate */
if (mmc_set_mod_clk(priv, mmc->clock))
return -1;
/* Clear internal divider */
rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK;
writel(rval, &priv->reg->clkcr);
#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
/* A64 supports calibration of delays on MMC controller and we
* have to set delay of zero before starting calibration.
* Allwinner BSP driver sets a delay only in the case of
* using HS400 which is not supported by mainline U-Boot or
* Linux at the moment
*/
writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
#endif
/* Re-enable Clock */
rval |= SUNXI_MMC_CLK_ENABLE;
writel(rval, &priv->reg->clkcr);
if (mmc_update_clk(priv))
return -1;
return 0;
}
static int sunxi_mmc_set_ios_common(struct sunxi_mmc_priv *priv,
struct mmc *mmc)
{
debug("set ios: bus_width: %x, clock: %d\n",
mmc->bus_width, mmc->clock);
/* Change clock first */
if (mmc->clock && mmc_config_clock(priv, mmc) != 0) {
priv->fatal_err = 1;
return -EINVAL;
}
/* Change bus width */
if (mmc->bus_width == 8)
writel(0x2, &priv->reg->width);
else if (mmc->bus_width == 4)
writel(0x1, &priv->reg->width);
else
writel(0x0, &priv->reg->width);
return 0;
}
#if !CONFIG_IS_ENABLED(DM_MMC)
static int sunxi_mmc_core_init(struct mmc *mmc)
{
struct sunxi_mmc_priv *priv = mmc->priv;
/* Reset controller */
writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl);
udelay(1000);
return 0;
}
#endif
static int mmc_trans_data_by_cpu(struct sunxi_mmc_priv *priv, struct mmc *mmc,
struct mmc_data *data)
{
const int reading = !!(data->flags & MMC_DATA_READ);
const uint32_t status_bit = reading ? SUNXI_MMC_STATUS_FIFO_EMPTY :
SUNXI_MMC_STATUS_FIFO_FULL;
unsigned i;
unsigned *buff = (unsigned int *)(reading ? data->dest : data->src);
unsigned byte_cnt = data->blocksize * data->blocks;
unsigned timeout_msecs = byte_cnt >> 8;
unsigned long start;
if (timeout_msecs < 2000)
timeout_msecs = 2000;
/* Always read / write data through the CPU */
setbits_le32(&priv->reg->gctrl, SUNXI_MMC_GCTRL_ACCESS_BY_AHB);
start = get_timer(0);
for (i = 0; i < (byte_cnt >> 2); i++) {
while (readl(&priv->reg->status) & status_bit) {
if (get_timer(start) > timeout_msecs)
return -1;
}
if (reading)
buff[i] = readl(&priv->reg->fifo);
else
writel(buff[i], &priv->reg->fifo);
}
return 0;
}
static int mmc_rint_wait(struct sunxi_mmc_priv *priv, struct mmc *mmc,
uint timeout_msecs, uint done_bit, const char *what)
{
unsigned int status;
unsigned long start = get_timer(0);
do {
status = readl(&priv->reg->rint);
if ((get_timer(start) > timeout_msecs) ||
(status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT)) {
debug("%s timeout %x\n", what,
status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT);
return -ETIMEDOUT;
}
} while (!(status & done_bit));
return 0;
}
static int sunxi_mmc_send_cmd_common(struct sunxi_mmc_priv *priv,
struct mmc *mmc, struct mmc_cmd *cmd,
struct mmc_data *data)
{
unsigned int cmdval = SUNXI_MMC_CMD_START;
unsigned int timeout_msecs;
int error = 0;
unsigned int status = 0;
unsigned int bytecnt = 0;
if (priv->fatal_err)
return -1;
if (cmd->resp_type & MMC_RSP_BUSY)
debug("mmc cmd %d check rsp busy\n", cmd->cmdidx);
if (cmd->cmdidx == 12)
return 0;
if (!cmd->cmdidx)
cmdval |= SUNXI_MMC_CMD_SEND_INIT_SEQ;
if (cmd->resp_type & MMC_RSP_PRESENT)
cmdval |= SUNXI_MMC_CMD_RESP_EXPIRE;
if (cmd->resp_type & MMC_RSP_136)
cmdval |= SUNXI_MMC_CMD_LONG_RESPONSE;
if (cmd->resp_type & MMC_RSP_CRC)
cmdval |= SUNXI_MMC_CMD_CHK_RESPONSE_CRC;
if (data) {
if ((u32)(long)data->dest & 0x3) {
error = -1;
goto out;
}
cmdval |= SUNXI_MMC_CMD_DATA_EXPIRE|SUNXI_MMC_CMD_WAIT_PRE_OVER;
if (data->flags & MMC_DATA_WRITE)
cmdval |= SUNXI_MMC_CMD_WRITE;
if (data->blocks > 1)
cmdval |= SUNXI_MMC_CMD_AUTO_STOP;
writel(data->blocksize, &priv->reg->blksz);
writel(data->blocks * data->blocksize, &priv->reg->bytecnt);
}
debug("mmc %d, cmd %d(0x%08x), arg 0x%08x\n", priv->mmc_no,
cmd->cmdidx, cmdval | cmd->cmdidx, cmd->cmdarg);
writel(cmd->cmdarg, &priv->reg->arg);
if (!data)
writel(cmdval | cmd->cmdidx, &priv->reg->cmd);
/*
* transfer data and check status
* STATREG[2] : FIFO empty
* STATREG[3] : FIFO full
*/
if (data) {
int ret = 0;
bytecnt = data->blocksize * data->blocks;
debug("trans data %d bytes\n", bytecnt);
writel(cmdval | cmd->cmdidx, &priv->reg->cmd);
ret = mmc_trans_data_by_cpu(priv, mmc, data);
if (ret) {
error = readl(&priv->reg->rint) &
SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT;
error = -ETIMEDOUT;
goto out;
}
}
error = mmc_rint_wait(priv, mmc, 1000, SUNXI_MMC_RINT_COMMAND_DONE,
"cmd");
if (error)
goto out;
if (data) {
timeout_msecs = 120;
debug("cacl timeout %x msec\n", timeout_msecs);
error = mmc_rint_wait(priv, mmc, timeout_msecs,
data->blocks > 1 ?
SUNXI_MMC_RINT_AUTO_COMMAND_DONE :
SUNXI_MMC_RINT_DATA_OVER,
"data");
if (error)
goto out;
}
if (cmd->resp_type & MMC_RSP_BUSY) {
unsigned long start = get_timer(0);
timeout_msecs = 2000;
do {
status = readl(&priv->reg->status);
if (get_timer(start) > timeout_msecs) {
debug("busy timeout\n");
error = -ETIMEDOUT;
goto out;
}
} while (status & SUNXI_MMC_STATUS_CARD_DATA_BUSY);
}
if (cmd->resp_type & MMC_RSP_136) {
cmd->response[0] = readl(&priv->reg->resp3);
cmd->response[1] = readl(&priv->reg->resp2);
cmd->response[2] = readl(&priv->reg->resp1);
cmd->response[3] = readl(&priv->reg->resp0);
debug("mmc resp 0x%08x 0x%08x 0x%08x 0x%08x\n",
cmd->response[3], cmd->response[2],
cmd->response[1], cmd->response[0]);
} else {
cmd->response[0] = readl(&priv->reg->resp0);
debug("mmc resp 0x%08x\n", cmd->response[0]);
}
out:
if (error < 0) {
writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl);
mmc_update_clk(priv);
}
writel(0xffffffff, &priv->reg->rint);
writel(readl(&priv->reg->gctrl) | SUNXI_MMC_GCTRL_FIFO_RESET,
&priv->reg->gctrl);
return error;
}
#if !CONFIG_IS_ENABLED(DM_MMC)
static int sunxi_mmc_set_ios_legacy(struct mmc *mmc)
{
struct sunxi_mmc_priv *priv = mmc->priv;
return sunxi_mmc_set_ios_common(priv, mmc);
}
static int sunxi_mmc_send_cmd_legacy(struct mmc *mmc, struct mmc_cmd *cmd,
struct mmc_data *data)
{
struct sunxi_mmc_priv *priv = mmc->priv;
return sunxi_mmc_send_cmd_common(priv, mmc, cmd, data);
}
static int sunxi_mmc_getcd_legacy(struct mmc *mmc)
{
struct sunxi_mmc_priv *priv = mmc->priv;
int cd_pin;
cd_pin = sunxi_mmc_getcd_gpio(priv->mmc_no);
if (cd_pin < 0)
return 1;
return !gpio_get_value(cd_pin);
}
static const struct mmc_ops sunxi_mmc_ops = {
.send_cmd = sunxi_mmc_send_cmd_legacy,
.set_ios = sunxi_mmc_set_ios_legacy,
.init = sunxi_mmc_core_init,
.getcd = sunxi_mmc_getcd_legacy,
};
struct mmc *sunxi_mmc_init(int sdc_no)
{
struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
struct sunxi_mmc_priv *priv = &mmc_host[sdc_no];
struct mmc_config *cfg = &priv->cfg;
int ret;
memset(priv, '\0', sizeof(struct sunxi_mmc_priv));
cfg->name = "SUNXI SD/MMC";
cfg->ops = &sunxi_mmc_ops;
cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
cfg->host_caps = MMC_MODE_4BIT;
#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN8I) || defined(CONFIG_MACH_SUN50I_H6)
if (sdc_no == 2)
cfg->host_caps = MMC_MODE_8BIT;
#endif
cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
cfg->f_min = 400000;
cfg->f_max = 52000000;
if (mmc_resource_init(sdc_no) != 0)
return NULL;
/* config ahb clock */
debug("init mmc %d clock and io\n", sdc_no);
#if !defined(CONFIG_MACH_SUN50I_H6)
setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MMC(sdc_no));
#ifdef CONFIG_SUNXI_GEN_SUN6I
/* unassert reset */
setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MMC(sdc_no));
#endif
#if defined(CONFIG_MACH_SUN9I)
/* sun9i has a mmc-common module, also set the gate and reset there */
writel(SUNXI_MMC_COMMON_CLK_GATE | SUNXI_MMC_COMMON_RESET,
SUNXI_MMC_COMMON_BASE + 4 * sdc_no);
#endif
#else /* CONFIG_MACH_SUN50I_H6 */
setbits_le32(&ccm->sd_gate_reset, 1 << sdc_no);
/* unassert reset */
setbits_le32(&ccm->sd_gate_reset, 1 << (RESET_SHIFT + sdc_no));
#endif
ret = mmc_set_mod_clk(priv, 24000000);
if (ret)
return NULL;
return mmc_create(cfg, priv);
}
#else
static int sunxi_mmc_set_ios(struct udevice *dev)
{
struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
struct sunxi_mmc_priv *priv = dev_get_priv(dev);
return sunxi_mmc_set_ios_common(priv, &plat->mmc);
}
static int sunxi_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
struct mmc_data *data)
{
struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
struct sunxi_mmc_priv *priv = dev_get_priv(dev);
return sunxi_mmc_send_cmd_common(priv, &plat->mmc, cmd, data);
}
static int sunxi_mmc_getcd(struct udevice *dev)
{
struct sunxi_mmc_priv *priv = dev_get_priv(dev);
if (dm_gpio_is_valid(&priv->cd_gpio)) {
int cd_state = dm_gpio_get_value(&priv->cd_gpio);
return cd_state ^ priv->cd_inverted;
}
return 1;
}
static const struct dm_mmc_ops sunxi_mmc_ops = {
.send_cmd = sunxi_mmc_send_cmd,
.set_ios = sunxi_mmc_set_ios,
.get_cd = sunxi_mmc_getcd,
};
static int sunxi_mmc_probe(struct udevice *dev)
{
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
struct sunxi_mmc_priv *priv = dev_get_priv(dev);
struct mmc_config *cfg = &plat->cfg;
struct ofnode_phandle_args args;
u32 *gate_reg, *ccu_reg;
int bus_width, ret;
cfg->name = dev->name;
bus_width = dev_read_u32_default(dev, "bus-width", 1);
cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
cfg->host_caps = 0;
if (bus_width == 8)
cfg->host_caps |= MMC_MODE_8BIT;
if (bus_width >= 4)
cfg->host_caps |= MMC_MODE_4BIT;
cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
cfg->f_min = 400000;
cfg->f_max = 52000000;
priv->reg = (void *)dev_read_addr(dev);
priv->variant =
(const struct sunxi_mmc_variant *)dev_get_driver_data(dev);
/* We don't have a sunxi clock driver so find the clock address here */
ret = dev_read_phandle_with_args(dev, "clocks", "#clock-cells", 0,
1, &args);
if (ret)
return ret;
ccu_reg = (u32 *)ofnode_get_addr(args.node);
priv->mmc_no = ((uintptr_t)priv->reg - SUNXI_MMC0_BASE) / 0x1000;
priv->mclkreg = (void *)ccu_reg +
(priv->variant->mclk_offset + (priv->mmc_no * 4));
gate_reg = (void *)ccu_reg + priv->variant->gate_offset;
setbits_le32(gate_reg, BIT(AHB_GATE_OFFSET_MMC(priv->mmc_no)));
ret = mmc_set_mod_clk(priv, 24000000);
if (ret)
return ret;
/* This GPIO is optional */
if (!gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
GPIOD_IS_IN)) {
int cd_pin = gpio_get_number(&priv->cd_gpio);
sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP);
}
/* Check if card detect is inverted */
priv->cd_inverted = dev_read_bool(dev, "cd-inverted");
upriv->mmc = &plat->mmc;
/* Reset controller */
writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl);
udelay(1000);
return 0;
}
static int sunxi_mmc_bind(struct udevice *dev)
{
struct sunxi_mmc_plat *plat = dev_get_platdata(dev);
return mmc_bind(dev, &plat->mmc, &plat->cfg);
}
static const struct sunxi_mmc_variant sun4i_a10_variant = {
.gate_offset = 0x60,
.mclk_offset = 0x88,
};
static const struct udevice_id sunxi_mmc_ids[] = {
{
.compatible = "allwinner,sun4i-a10-mmc",
.data = (ulong)&sun4i_a10_variant,
},
{
.compatible = "allwinner,sun5i-a13-mmc",
.data = (ulong)&sun4i_a10_variant,
},
{
.compatible = "allwinner,sun7i-a20-mmc",
.data = (ulong)&sun4i_a10_variant,
},
{ /* sentinel */ }
};
U_BOOT_DRIVER(sunxi_mmc_drv) = {
.name = "sunxi_mmc",
.id = UCLASS_MMC,
.of_match = sunxi_mmc_ids,
.bind = sunxi_mmc_bind,
.probe = sunxi_mmc_probe,
.ops = &sunxi_mmc_ops,
.platdata_auto_alloc_size = sizeof(struct sunxi_mmc_plat),
.priv_auto_alloc_size = sizeof(struct sunxi_mmc_priv),
};
#endif