mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
192 lines
4.9 KiB
C
192 lines
4.9 KiB
C
/*
|
|
* (C) Copyright 2005-2007
|
|
* Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <command.h>
|
|
#include <malloc.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
extern void lxt971_no_sleep(void);
|
|
|
|
int board_early_init_f (void)
|
|
{
|
|
/*
|
|
* IRQ 0-15 405GP internally generated; active high; level sensitive
|
|
* IRQ 16 405GP internally generated; active low; level sensitive
|
|
* IRQ 17-24 RESERVED
|
|
* IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
|
|
* IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
|
|
* IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
|
|
* IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
|
|
* IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
|
|
* IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
|
|
* IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
|
|
*/
|
|
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
mtdcr(UIC0ER, 0x00000000); /* disable all ints */
|
|
mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
|
|
mtdcr(UIC0PR, 0xFFFFFF80); /* set int polarities */
|
|
mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
|
|
mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
|
|
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
|
|
/*
|
|
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
|
|
*/
|
|
mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
|
|
|
|
/*
|
|
* Reset CPLD via GPIO12 (CS3) pin
|
|
*/
|
|
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_PLD_RESET);
|
|
udelay(1000); /* wait 1ms */
|
|
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CONFIG_SYS_PLD_RESET);
|
|
udelay(1000); /* wait 1ms */
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r (void)
|
|
{
|
|
/* adjust flash start and offset */
|
|
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
|
|
gd->bd->bi_flashoffset = 0;
|
|
|
|
/*
|
|
* Setup and enable EEPROM write protection
|
|
*/
|
|
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
|
|
|
|
return (0);
|
|
}
|
|
|
|
|
|
/*
|
|
* Check Board Identity:
|
|
*/
|
|
#define LED_REG (CONFIG_SYS_PLD_BASE + 0x1000)
|
|
int checkboard (void)
|
|
{
|
|
char str[64];
|
|
int flashcnt;
|
|
int delay;
|
|
|
|
puts ("Board: ");
|
|
|
|
if (getenv_f("serial#", str, sizeof(str)) == -1) {
|
|
puts ("### No HW ID - assuming CMS700");
|
|
} else {
|
|
puts(str);
|
|
}
|
|
|
|
printf(" (PLD-Version=%02d)\n",
|
|
in_8((void *)(CONFIG_SYS_PLD_BASE + 0x1001)));
|
|
|
|
/*
|
|
* Flash LEDs
|
|
*/
|
|
for (flashcnt = 0; flashcnt < 3; flashcnt++) {
|
|
out_8((void *)LED_REG, 0x00); /* LEDs off */
|
|
for (delay = 0; delay < 100; delay++)
|
|
udelay(1000);
|
|
out_8((void *)LED_REG, 0x0f); /* LEDs on */
|
|
for (delay = 0; delay < 50; delay++)
|
|
udelay(1000);
|
|
}
|
|
out_8((void *)LED_REG, 0x70);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
#if defined(CONFIG_SYS_EEPROM_WREN)
|
|
/* Input: <dev_addr> I2C address of EEPROM device to enable.
|
|
* <state> -1: deliver current state
|
|
* 0: disable write
|
|
* 1: enable write
|
|
* Returns: -1: wrong device address
|
|
* 0: dis-/en- able done
|
|
* 0/1: current state if <state> was -1.
|
|
*/
|
|
int eeprom_write_enable (unsigned dev_addr, int state)
|
|
{
|
|
if (CONFIG_SYS_I2C_EEPROM_ADDR != dev_addr) {
|
|
return -1;
|
|
} else {
|
|
switch (state) {
|
|
case 1:
|
|
/* Enable write access, clear bit GPIO_SINT2. */
|
|
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP);
|
|
state = 0;
|
|
break;
|
|
case 0:
|
|
/* Disable write access, set bit GPIO_SINT2. */
|
|
out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
|
|
state = 0;
|
|
break;
|
|
default:
|
|
/* Read current status back. */
|
|
state = (0 == (in_be32((void *)GPIO0_OR) & CONFIG_SYS_EEPROM_WP));
|
|
break;
|
|
}
|
|
}
|
|
return state;
|
|
}
|
|
|
|
int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
|
|
{
|
|
int query = argc == 1;
|
|
int state = 0;
|
|
|
|
if (query) {
|
|
/* Query write access state. */
|
|
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, -1);
|
|
if (state < 0) {
|
|
puts ("Query of write access state failed.\n");
|
|
} else {
|
|
printf ("Write access for device 0x%0x is %sabled.\n",
|
|
CONFIG_SYS_I2C_EEPROM_ADDR, state ? "en" : "dis");
|
|
state = 0;
|
|
}
|
|
} else {
|
|
if ('0' == argv[1][0]) {
|
|
/* Disable write access. */
|
|
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 0);
|
|
} else {
|
|
/* Enable write access. */
|
|
state = eeprom_write_enable (CONFIG_SYS_I2C_EEPROM_ADDR, 1);
|
|
}
|
|
if (state < 0) {
|
|
puts ("Setup of write access state failed.\n");
|
|
}
|
|
}
|
|
|
|
return state;
|
|
}
|
|
|
|
U_BOOT_CMD(eepwren, 2, 0, do_eep_wren,
|
|
"Enable / disable / query EEPROM write access",
|
|
""
|
|
);
|
|
#endif /* #if defined(CONFIG_SYS_EEPROM_WREN) */
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
void reset_phy(void)
|
|
{
|
|
#ifdef CONFIG_LXT971_NO_SLEEP
|
|
|
|
/*
|
|
* Disable sleep mode in LXT971
|
|
*/
|
|
lxt971_no_sleep();
|
|
#endif
|
|
}
|