mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
c346e466e0
This prevents some warnings when building with clang. cc:: andreas.devel@googlemail.com Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
281 lines
7.5 KiB
C
281 lines
7.5 KiB
C
/*
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/at91sam9261.h>
|
|
#include <asm/arch/at91sam9261_matrix.h>
|
|
#include <asm/arch/at91sam9_smc.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/at91_pmc.h>
|
|
#include <asm/arch/at91_rstc.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <lcd.h>
|
|
#include <atmel_lcdc.h>
|
|
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#endif
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
/*
|
|
* Miscelaneous platform dependent initialisations
|
|
*/
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
static void at91sam9261ek_nand_hw_init(void)
|
|
{
|
|
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
|
|
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
|
|
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
|
|
unsigned long csa;
|
|
|
|
/* Enable CS3 */
|
|
csa = readl(&matrix->ebicsa);
|
|
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
|
|
|
|
writel(csa, &matrix->ebicsa);
|
|
|
|
/* Configure SMC CS3 for NAND/SmartMedia */
|
|
#ifdef CONFIG_AT91SAM9G10EK
|
|
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) |
|
|
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7),
|
|
&smc->cs[3].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
|
|
&smc->cs[3].cycle);
|
|
#else
|
|
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
|
|
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
|
|
&smc->cs[3].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
|
|
&smc->cs[3].cycle);
|
|
#endif
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
#ifdef CONFIG_SYS_NAND_DBW_16
|
|
AT91_SMC_MODE_DBW_16 |
|
|
#else /* CONFIG_SYS_NAND_DBW_8 */
|
|
AT91_SMC_MODE_DBW_8 |
|
|
#endif
|
|
AT91_SMC_MODE_TDF_CYCLE(2),
|
|
&smc->cs[3].mode);
|
|
|
|
writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
|
|
|
|
/* Configure RDY/BSY */
|
|
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
|
|
|
|
/* Enable NandFlash */
|
|
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
|
|
|
|
at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */
|
|
at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
static void at91sam9261ek_dm9000_hw_init(void)
|
|
{
|
|
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
|
|
|
|
/* Configure SMC CS2 for DM9000 */
|
|
#ifdef CONFIG_AT91SAM9G10EK
|
|
writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[2].setup);
|
|
writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) |
|
|
AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8),
|
|
&smc->cs[2].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
|
|
&smc->cs[2].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
|
|
AT91_SMC_MODE_TDF_CYCLE(1),
|
|
&smc->cs[2].mode);
|
|
#else
|
|
writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[2].setup);
|
|
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
|
|
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
|
|
&smc->cs[2].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
|
|
&smc->cs[2].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
|
|
AT91_SMC_MODE_TDF_CYCLE(1),
|
|
&smc->cs[2].mode);
|
|
#endif
|
|
|
|
/* Configure Reset signal as output */
|
|
at91_set_gpio_output(AT91_PIN_PC10, 0);
|
|
|
|
/* Configure Interrupt pin as input, no pull-up */
|
|
at91_set_gpio_input(AT91_PIN_PC11, 0);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_LCD
|
|
vidinfo_t panel_info = {
|
|
.vl_col = 240,
|
|
.vl_row = 320,
|
|
.vl_clk = 4965000,
|
|
.vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
|
|
ATMEL_LCDC_INVFRAME_INVERTED,
|
|
.vl_bpix = 3,
|
|
.vl_tft = 1,
|
|
.vl_hsync_len = 5,
|
|
.vl_left_margin = 1,
|
|
.vl_right_margin = 33,
|
|
.vl_vsync_len = 1,
|
|
.vl_upper_margin = 1,
|
|
.vl_lower_margin = 0,
|
|
.mmio = ATMEL_BASE_LCDC,
|
|
};
|
|
|
|
void lcd_enable(void)
|
|
{
|
|
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
|
|
}
|
|
|
|
void lcd_disable(void)
|
|
{
|
|
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
|
|
}
|
|
|
|
static void at91sam9261ek_lcd_hw_init(void)
|
|
{
|
|
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
|
|
|
|
at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */
|
|
at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */
|
|
at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */
|
|
at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */
|
|
at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */
|
|
at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */
|
|
at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */
|
|
at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */
|
|
at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */
|
|
at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */
|
|
at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */
|
|
at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */
|
|
at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */
|
|
at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */
|
|
at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */
|
|
at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */
|
|
at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */
|
|
at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */
|
|
at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */
|
|
at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */
|
|
at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */
|
|
at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */
|
|
|
|
writel(AT91_PMC_HCK1, &pmc->scer);
|
|
|
|
/* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */
|
|
#ifdef CONFIG_AT91SAM9261EK
|
|
gd->fb_base = ATMEL_BASE_SRAM;
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_LCD_INFO
|
|
#include <nand.h>
|
|
#include <version.h>
|
|
|
|
void lcd_show_board_info(void)
|
|
{
|
|
ulong dram_size, nand_size;
|
|
int i;
|
|
char temp[32];
|
|
|
|
lcd_printf ("%s\n", U_BOOT_VERSION);
|
|
lcd_printf ("(C) 2008 ATMEL Corp\n");
|
|
lcd_printf ("at91support@atmel.com\n");
|
|
lcd_printf ("%s CPU at %s MHz\n",
|
|
ATMEL_CPU_NAME,
|
|
strmhz(temp, get_cpu_clk_rate()));
|
|
|
|
dram_size = 0;
|
|
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
|
|
dram_size += gd->bd->bi_dram[i].size;
|
|
nand_size = 0;
|
|
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
|
|
nand_size += nand_info[i].size;
|
|
lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
|
|
dram_size >> 20,
|
|
nand_size >> 20 );
|
|
}
|
|
#endif /* CONFIG_LCD_INFO */
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
#ifdef CONFIG_AT91SAM9G10EK
|
|
/* arch number of AT91SAM9G10EK-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
|
|
#else
|
|
/* arch number of AT91SAM9261EK-Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
|
|
#endif
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
at91_seriald_hw_init();
|
|
#ifdef CONFIG_CMD_NAND
|
|
at91sam9261ek_nand_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_HAS_DATAFLASH
|
|
at91_spi0_hw_init(1 << 0);
|
|
#endif
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
at91sam9261ek_dm9000_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_LCD
|
|
at91sam9261ek_lcd_hw_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
return dm9000_initialize(bis);
|
|
}
|
|
#endif
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
|
|
CONFIG_SYS_SDRAM_SIZE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
void reset_phy(void)
|
|
{
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
/*
|
|
* Initialize ethernet HW addr prior to starting Linux,
|
|
* needed for nfsroot
|
|
*/
|
|
eth_init(gd->bd);
|
|
#endif
|
|
}
|
|
#endif
|